JPN CORPORATION
===============

   CA8301E, CA8302E

   Data bus:           16-bit, ISA                                
   Size:               Half-length, full-height card              
   Hard drive          Two IDE (AT) Interface drives              
   supported:          
   Floppy drives       Two 360KB, 720KB, 1.2MB, or 1.44MB drives  
   supported:          
   Maximum heads/cyl.: 8 heads and 1024 cylinders                 
   Special Features    Two serial, one game, and one parallel     
                       port                                       
                       (Only one serial port on the CA80301E)     

<gopher://bitreich.org/I/th99/c/I-L/20258-1.png>
   

   +------------------------------------------------------------+
   |                        CONNECTIONS                         |
   |------------------------------------------------------------|
   |                    Function                     | Location |
   |-------------------------------------------------+----------|
   | 40-pin IDE (AT) Interface control cable         |   CN1    |
   | connector                                       |          |
   |-------------------------------------------------+----------|
   | 34-pin control cable connector-hard drive       |   CN2    |
   |-------------------------------------------------+----------|
   | 9-pin serial port (COM2/4)-internal             |   CN3    |
   |-------------------------------------------------+----------|
   | 9-pin serial port (COM1/3)-internal             |   CN4    |
   |-------------------------------------------------+----------|
   | 15-pin game port - external                     |   CN5    |
   |-------------------------------------------------+----------|
   | 25-pin parallel port (LPT1/2) - external        |   CN6    |
   |-------------------------------------------------+----------|
   | 4-pin connector-drive active LED                |   CN7    |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |                 USER CONFIGURABLE SETTINGS                 |
   |------------------------------------------------------------|
   |            Function            |   Location   |  Setting   |
   |--------------------------------+--------------+------------|
   |>> | Serial port 1 is set for   | JP6/jumper1  | pins 1 & 2 |
   |   | COM1                       |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Serial port 1 is set for   | JP6/jumper1  | pins 2 & 3 |
   |   | COM3                       |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Serial port 1 enabled      | JP6/jumper 2 | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Serial port 1 disabled     | JP6/jumper 2 | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Serial port 2 is set for   | JP6/jumper 3 | pins 1 & 2 |
   |   | COM2                       |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Serial port 2 is set for   | JP6/jumper 3 | pins 2 & 3 |
   |   | COM4                       |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Serial port 2 enabled      | JP6/jumper 4 | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Serial port 2 disabled     | JP6/jumper 4 | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Parallel port is set for   | JP6/jumper 5 | pins 1 & 2 |
   |   | LPT1 (I/O address 378h)    |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Parallel port is set for   | JP6/jumper 5 | pins 2 & 3 |
   |   | LPT2 (I/O address 278h)    |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Parallel port enabled      | JP6/jumper 6 | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Parallel port disabled     | JP6/jumper 6 | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Game port enabled          | JP6/jumper 7 | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Game port disabled         | JP6/jumper 7 | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Floppy drive enabled       | JP6/jumper 8 | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Floppy drive disabled      | JP6/jumper 8 | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Hard drive enabled         |     JP7      | pins 1 & 2 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Hard drive disabled        |     JP7      | pins 2 & 3 |
   |   |                            |              |   closed   |
   |---+----------------------------+--------------+------------|
   |>> | Parallel port is set for   |     JP8      | pins 2 & 3 |
   |   | IRQ7                       |              |   closed   |
   |---+----------------------------+--------------+------------|
   |   | Parallel port is set for   |     JP8      | pins 1 & 2 |
   |   | IRQ5                       |              |   closed   |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |               SERIAL PORT IRQ JUMPERS - JP9                |
   |------------------------------------------------------------|
   |  IRQ   |  Jumper 1  |  Jumper 2  |  Jumper 3  |  Jumper 4  |
   |        |            |            |            |            |
   |        | 1-2-COM1/3 | 1-2-COM1/3 | 1-2-COM1/3 | 1-2-COM1/3 |
   |        |            |            |            |            |
   |        | 2-3-COM2/4 | 2-3-COM2/4 | 2-3-COM2/4 | 2-3-COM2/4 |
   |--------+------------+------------+------------+------------|
   |>> | 5  |   closed   |    open    |    open    |    open    |
   |---+----+------------+------------+------------+------------|
   |   | 4  |    open    |   closed   |    open    |    open    |
   |---+----+------------+------------+------------+------------|
   |   | 3  |    open    |    open    |   closed   |    open    |
   |---+----+------------+------------+------------+------------|
   |   | 2  |    open    |    open    |    open    |   closed   |
   +------------------------------------------------------------+

   +------------------------------------------------------------+
   |               MISCELLANEOUS TECHNICAL NOTES                |
   |------------------------------------------------------------|
   |   JP9/jumpers 1 to 4 select Interrupt request for serial   |
   | port 1 & 2. Pins 1 - 2 apply to serial port 1 (COM1/3) and |
   |  pins 2 & 3 apply to serial port 2 (COM2/4). The factory   |
   | defaults are JP9/jumper 2/pins 1-2 "closed" (COM1/3-IRQ4)  |
   |      & JP9/jumper 3 pins 2-3 "closed" (COM2/4-IRQ3).       |
   +------------------------------------------------------------+