APEX DATA, INC. =============== V.32BIS DATA/FAX MODEM Card Type Fax, Modem (synchronous/asynchronous), Voice Chip Set Unidentified I/O Options Speakerphone, Voice-mail Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus Unidentified Fax Class Class I & II Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.32, V.32bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression 53109 +-------------------------------+ | MISCELLANEOUS TECHNICAL NOTES | |-------------------------------| | Diagram not available | +-------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, 'Comma', A/ | |------------------------------------------------------------| | A, B, C, E, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &G, &J, &K, &L, &M, &O, &P, &Q, &R, &S, &T, &V, | | &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \F, \G, \J, \K, \L, \N, \Q, \V, \X | |------------------------------------------------------------| | %C, %D, %E, %L, %Q | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | *H, -J, -K, -Q, )M, #CID | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S25, S26, S32, S33 | |------------------------------------------------------------| | S36, S37, S38, S46, S48, S86, S91, S92, S95 | |------------------------------------------------------------| | Note: See MHI Help file for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | ACTIVE CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \S [cmds] | |--------------+---------------------------------------------| | Description: | Displays the current configuration in long | | | form | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | i &E1 | Auto-retrain and auto-fallback enabled | |--------------+---------------------------------------------| | &E2 | Auto-fallback/fall-forward enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC ADDRESS CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Defines the BSC sync character or the HDLC | | | address | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S19 | |------------------------------------------------------------| | Format: | AT [cmds] S19=n [cmds] | |-----------------+------------------------------------------| | Default: | 16 | |-----------------+------------------------------------------| | Range: | 0-30 | |-----------------+------------------------------------------| | Description: | Controls Hayes AutoSync functions | |------------------------------------------------------------| | Bit | Value | Function | |---------+----------+---------------------------------------| | 0 | i 0 | Not used | |------------------------------------------------------------| | 1 | i 0 | BSC enabled | | | | | | | 1 | SDLC enabled | |-------------+---------+------------------------------------| | 2 | i 0 | SDLC address disabled | | | | | | | 1 | SDLC address enabled | |-------------+---------+------------------------------------| | 3 | i 0 | NRZI enabled | | | | | | | 1 | NZI enabled | |-------------+---------+------------------------------------| | 4 | 0 | SDLC idle on Mark enabled | | | | | | | i 1 | SDLC idle on FLAG enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls pulse dialing and MNP10 link | | | negotiation. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 2 - | i 000 | Not used | | 0 | | | |------+-------+---------------------------------------------| | 4, 3 | i 00 | 39ms make/61ms break at 10pps | | | | | | | 01 | 33ms make/67ms break at 10pps | | | | | | | 10 | 39ms make/61ms break at 20pps | | | | | | | 11 | 33ms make/67ms break at 20pps | |------+-------+---------------------------------------------| | 5 | i 0 | Not used | |------+-------+---------------------------------------------| | 7, 6 | i 00 | Link will be negotiated at highest possible | | | | speed | | | 01 | | | | | Link will be negotiated at 1200bps | | | 10 | | | | | Link will be negotiated at 4800bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | 202 | |----------------+-------------------------------------------| | Range: | 0-255 | |----------------+-------------------------------------------| | Description: | Select automode, extended result code | | | format, caller ID functions. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | i 0 | Not used | |----------+-------+-----------------------------------------| | 1 | 0 | Auto-mode detection disabled | | | | | | | i 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted | | | | with the following protocols in order - | | | | V.FC, V.32bis, V.32, V.22bis, V.22 or | | | | Bell 212, V.21, and Bell 103 | |----------+-------+-----------------------------------------| | 3, 2 | 00 | Enables CONNECT result codes to report | | | | DTE speed | | | 01 | | | | | Full reporting of CONNECT result codes | | | i 10 | | | | | Enables CONNECT result codes to report | | | | DCE speed | |----------+-------+-----------------------------------------| | 5, 4 | i 00 | Caller ID disabled | | | | | | | 01 | Caller ID displays formatted data | | | | | | | 10 | Caller ID displays raw hexadecimal data | |----------+-------+-----------------------------------------| | 7, 6 | i 11 | Not used | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S40 | |------------------------------------------------------------| | Format | AT [cmds] S40=n [cmds] | |--------------+---------------------------------------------| | Default: | 233 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls power level and break handling; | | | selects MNP10 extended services, and block | | | size. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1, 0 | 00 | MNP10 extended services disabled | | | | | | | i 01 | MNP10 extended services enabled | | | | | | | 10 | MNP10 extended services enabled without | | | | indicating MNP on the answer detection | | | | phase. | |------+-------+---------------------------------------------| | 2 | i 0 | Power level adjustment disabled | | | | | | | 1 | Power level adjustment enabled | |------+-------+---------------------------------------------| | 5, | 000 | \K0 | | 4, 3 | | | | | 001 | \K1 | | | | | | | 010 | \K2 | | | | | | | 011 | \K3 | | | | | | | 100 | \K4 | | | | | | | i 101 | \K5 | |------+-------+---------------------------------------------| | 7, 6 | 00 | MNP block size is 64 characters | | | | | | | 01 | MNP block size is 128 characters | | | | | | | 10 | MNP block size is 192 characters | | | | | | | i 11 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | 135 | |--------------+---------------------------------------------| | Range: | 0-191 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects compression, auto-retrain, flow | | | control, MNP mode, lock serial port, | | | auto-fallback/fall-forward, and MNP10 - | | | fallback. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1 - | 00 | Data compression disabled | | 0 | | | | | 01 | MNP5 enabled | | | | | | | 10 | V.42bis enabled | | | | | | | i 11 | MNP5 and V.42bis enabled | |------+-------+---------------------------------------------| | 2 | 0 | Auto-retrain disabled | | | | | | | i 1 | Auto-retrain enabled | |------+-------+---------------------------------------------| | 3 | i 0 | Flow control disabled | | | | | | | 1 | Flow control enabled | |------+-------+---------------------------------------------| | 4 | i 0 | Stream mode for MNP | | | | | | | 1 | Block mode for MNP | |------+-------+---------------------------------------------| | 5 | i 0 | Serial speed locked | | | | | | | 1 | Serial speed follows connect speed | |------+-------+---------------------------------------------| | 6 | i 0 | Enable auto-fallback/fall-forward | |------+-------+---------------------------------------------| | 7 | 0 | MNP10 to fall back to speeds slower than | | | | 4800bps disabled | | | i 1 | | | | | MNP10 to fall back to speeds slower than | | | | 4800bps enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CHANGE PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *C [cmds] | |--------------+---------------------------------------------| | Description: | Change remote configuration password | |--------------+---------------------------------------------| | Note: | Must be 6-12 characters long. Default = | | | QWERTY | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &U0 | Data compression disabled | |--------------+---------------------------------------------| | i &U1 | Data compression enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | i %C1 | Data compression enabled | |--------------+---------------------------------------------| | %C2 | V.42bis enabled | |--------------+---------------------------------------------| | %C3 | MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COUNTRY CODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *NCn [cmds] | |--------------+---------------------------------------------| | Description: | Select country code | |--------------+---------------------------------------------| | Note: | Not available on U.S. versions | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the highest speed possible | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | %B300 | Set to 300bps | |----------------+-------------------------------------------| | %B1200 | Set to 1200bps | |----------------+-------------------------------------------| | %B2400 | Set to 2400bps | |----------------+-------------------------------------------| | %B4800 | Set to 4800bps | |----------------+-------------------------------------------| | %B9600 | Set to 9600bps | |----------------+-------------------------------------------| | %B7200 | Set to 7200bps | |----------------+-------------------------------------------| | %B12000 | Set to 12Kbps | |----------------+-------------------------------------------| | %B14400 | Set to14.4Kbps with V.32bis options | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE SPEED CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Gn [cmds] | |--------------+---------------------------------------------| | Description: | Controls how the modem responses to AT%B | | | command | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i %G0 | AT%B command disabled, DCE speed highest | | | possible or set according to ATF, ATS37 or | | | ATN | |---------------+--------------------------------------------| | %G1 | AT%B command enabled by way of AT%G1 or | | | AT%Bn, AT%B command set to current DTE | | | speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Modifier | Function | |--------------+---------------------------------------------| | L | Re-dial last number | |--------------+---------------------------------------------| | P | Pulse dialing enabled | |--------------+---------------------------------------------| | R | Answer mode enabled, originate mode | | | disabled following handshake initiation | |--------------+---------------------------------------------| | S=n | Dial stored telephone number n | |--------------+---------------------------------------------| | T | Tone dialing enabled | |--------------+---------------------------------------------| | W | Dialing resumed following dial tone | | | detection for amount of time specified in | | | S6 register | |--------------+---------------------------------------------| | , | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | ! | Modem commanded to go off-hook for amount | | | of time specified in S29 register before | | | returning on-hook | |--------------+---------------------------------------------| | @ | Wait for quiet answer, 5 second delay | |--------------+---------------------------------------------| | ; | Modem returned to command state after | | | dialing | |--------------+---------------------------------------------| | ^ | Toggle calling tone enabled/disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CALLBACK NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *L [cmds] | |--------------+---------------------------------------------| | Description: | Displays callback numbers in directories | | | 0-19 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY FIRMWARE VERSION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %V [cmds] | |--------------+---------------------------------------------| | Description: | Displays firmware version | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY S-REGISTERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %R [cmds] | |--------------+---------------------------------------------| | Description: | Displays all S-registers | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXIT REMOTE CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *X [cmds] | |--------------+---------------------------------------------| | Description: | Exit remote configuration | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | &F0 | V.42 factory defaults | |---------------+--------------------------------------------| | &F1 | MNP factory defaults | |---------------+--------------------------------------------| | &F2 | Basic asynchronous operation defaults | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S39? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the current flow control | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Flow control disabled | |--------------+---------------------------------------------| | 3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | 4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | 6 | Both RTS/CTS and XON/XOFF flow control | | | enabled | |--------------+---------------------------------------------| | 7 | XON/XOFF passthrough enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S30=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating hang-up | | | process. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Bn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &B0 | Serial speed follows connect speed | |--------------+---------------------------------------------| | i &B1 | Serial speed locked | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Fn [cmds] | |--------------+---------------------------------------------| | Description: | Controls line modulation unless automode is | | | selected | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | F0 | Automode enabled | |----------------+-------------------------------------------| | F1 | Force V.21 or Bell103 (according to ATB | | | command) at 300bps | |----------------+-------------------------------------------| | F2 | 'OK' returned | |----------------+-------------------------------------------| | F3 | Force V.23 75TX/1200RX originate or | | | 1200TX/75RX answer FSK | |----------------+-------------------------------------------| | F4 | Force V.22 or Bell212A (according to ATB | | | command) at 1200bps | |----------------+-------------------------------------------| | F5 | Force V.22bis or Bell2400 (according to | | | ATB command) | |----------------+-------------------------------------------| | F6 | Force V.32 at 4800bps | |----------------+-------------------------------------------| | F7 | Force V.32 at 7200bps | |----------------+-------------------------------------------| | F8 | Force V.32 at 9600bps | |----------------+-------------------------------------------| | F9 | Force V.32bis at 12000bps | |----------------+-------------------------------------------| | F10 | Force V.32bis at 14400bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - CLASS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Cn [cmds] | |--------------+---------------------------------------------| | Description: | Select the type of class for MNP10 | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | i -C0 | Enable MNP10, CLASS 10 selection, | | | synchronous | |----------------+-------------------------------------------| | -C1 | Enable MNP10, CLASS 10 selection, | | | asynchronous | |----------------+-------------------------------------------| | -C2 | Enable MNP10, CLASS 3 selection | |----------------+-------------------------------------------| | -C3 | Enable MNP10, CLASS 2 selection | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 FALLBACK | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] -B [cmds] | |--------------+---------------------------------------------| | Description: | During MNP10 link fallback to the next | | | lower speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 FALL-FORWARD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] -U [cmds] | |--------------+---------------------------------------------| | Description: | During MNP10 link fall-forward to the next | | | higher speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | NUMERIC RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects which type of result codes are | | | displayed | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | &N0 | Hayes format, normal numeric result codes | |---------------+--------------------------------------------| | i &N1 | Micrcom QX/4232hs-compatible numeric | | | result codes | |---------------+--------------------------------------------| | &N2 | Rockwell numeric result codes, allows | | | forced messages enabled in S95 | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD - LOGON /CALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Pn=xxx=yyy [cmds] | |--------------+---------------------------------------------| | Description: | Set password for callback and logon | |--------------+---------------------------------------------| | Note: | n=0-19 xxx=password yyy=callback number. If | | | there are no callback numbers in the | | | directory logon access only. If security is | | | active and there's no callback numbers, the | | | modem will not accept any passwords and | | | hang-up. | +------------------------------------------------------------+ +------------------------------------------------------------+ | READ-ONLY REGISTERS | |------------------------------------------------------------| | Register | Default | |-------------------------------+----------------------------| | S14 | 138 | |-------------------------------+----------------------------| | S21 | 0 | |-------------------------------+----------------------------| | S22 | 52 | |-------------------------------+----------------------------| | S23 | 59 | |-------------------------------+----------------------------| | S27 | 73 | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION - ENTER/EXIT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *En [cmds] | |--------------+---------------------------------------------| | Description: | Enter/exit remote configuration, RCM not | | | stored, configure with each use | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | *E0 | Exit remote configuration | |---------------+--------------------------------------------| | *E1 | Enter remote configuration access, '****' | | | from remote allows entry | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION - MNP ONLY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *R [cmds] | |--------------+---------------------------------------------| | Description: | Enter remote configuration during MNP mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem model and speed | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests ROM checksum, and reports 'OK' or | | | 'ERROR' | |--------------+---------------------------------------------| | I3 | Reports firmware revision | |--------------+---------------------------------------------| | I4 | Reports manufacturer's testing string | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports data pump type | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Sn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the security feature for logon and | | | callback | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | i -S0 | Security disabled | |-----------------+------------------------------------------| | -S1 | Security enabled | |-----------------+------------------------------------------| | -S2 | Current security configuration saved in | | | NVRAM | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S24=n [cmds] | |--------------+---------------------------------------------| | Default: | 5 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 seconds | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating low-power sleep | | | mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - CELLULAR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @Mn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in cellular mode, MNP10 | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | @M0 | Initial transmit level fixed | |--------------+---------------------------------------------| | @M1 | Initial transmit level last used |