CARDINAL TECHNOLOGIES, INC ========================== 9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1) Card Type Modem (asynchronous) Chip Set Unidentified Maximum Data Rate 9600bps Maximum Fax Rate Unidentified Data Bus 8-bit ISA Fax Class Class I & II Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.32 Fax Modulation Protocol Unidentified Error Correction/Compression MNP5, V.42, V.42bis +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out/in | CN1 | Line in/out | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | |--------------------+-------------------+-------------------| | COM1 (3F8h) | Off | Off | |--------------------+-------------------+-------------------| | COM2 (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3 (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4 (2E8h) | On | On | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting | SW1/3 | SW1/4 | |--------------------+-------------------+-------------------| | 2 | On | On | |--------------------+-------------------+-------------------| | 3 | Off | On | |--------------------+-------------------+-------------------| | 4 | Off | Off | |--------------------+-------------------+-------------------| | 5 | On | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, 'Comma', A/ | |------------------------------------------------------------| | A, B, C, E, F, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, | | &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \O, \U, \V, \X, \Y, \Z | |------------------------------------------------------------| | %A, %E, %G | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S25 | |------------------------------------------------------------| | S26, S27, S30, S37, S95, S108, S109, S110 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | "H, "O, -C, -J, -V | |------------------------------------------------------------| | Note: Please see MHI Help file for full command | | documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |--------------+---------------------------------------------| | Default: | 15 | |--------------+---------------------------------------------| | Range: | 0-191 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Remote digital loopback denied | | | | | | | i 1 | Remote digital loopback allowed | |------+-------+---------------------------------------------| | 3 - | 000 | Sets serial port speed to 0-300bps | | 1 | | | | | 001 | Sets serial port speed to 1200bps | | | | | | | 010 | Sets serial port speed to 2400bps | | | | | | | 011 | Sets serial port speed to 4800bps | | | | | | | 100 | Sets serial port speed to 7200bps | | | | | | | 101 | Sets serial port speed to 9600bps or | | | | 14400bps | | | 110 | | | | | Sets serial port speed to 19200bps | | | i 111 | | | | | Sets serial port speed to 38400bps or | | | | 57600bps | |------+-------+---------------------------------------------| | 5, 4 | i 00 | Parity even | | | | | | | 01 | Space or No parity | | | | | | | 10 | Parity odd | | | | | | | 11 | Mark Parity | |------+-------+---------------------------------------------| | 7, 6 | i 00 | Guard tone disabled | | | | | | | 01 | Guard tone 550Hz enabled | | | | | | | 10 | Guard tone 1800Hz enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| |Type: |Configuration | |-----------------+------------------------------------------| |Format: |AT [cmds] \Kn [cmds] | |-----------------+------------------------------------------| |Description: |Configures action of break signal | |------------------------------------------------------------| | Command |Break from | Modem | Break from | Break | | | DTE in |receives \B | DTE in | received | | |RELIABLE or| during |DIRECT mode |from remote| | |NORMAL mode| command | | modem | | | | state | | | |----------+-----------+------------+------------+-----------| | \K0 |Online |Break sent |Online |Buffers | | |command |to remote |command mode|cleared, | | |mode |modem and |enabled, |break sent | | |enabled, |buffers |send break |to DTE | | |send no |cleared |to remote | | | |break to | |modem | | | |remote | | | | | |modem | | | | |----------+-----------+------------+------------+-----------| | \K1 |Break sent |Break sent |Send break |Buffers | | |to remote |to remote |to remote |cleared, | | |modem and |modem and |modem |break sent | | |buffers |buffers |immediately |to DTE | | |cleared |cleared | | | |----------+-----------+------------+------------+-----------| | \K2 |Online |Send break |Online |Break sent | | |command |to remote |command mode|immediately| | |mode |modem |enabled, |to DTE | | |enabled, |immediately |send break | | | |send no | |to remote | | | |break to | |modem | | | |remote | | | | | |modem | | | | |----------+-----------+------------+------------+-----------| | \K3 |Send break |Send break |Send break |Break sent | | |to remote |to remote |to remote |immediately| | |modem |modem |modem |to DTE | | |immediately|immediately |immediately | | |----------+-----------+------------+------------+-----------| | \K4 |Online |Send break |Online |Break sent | | |command |with |command mode|with | | |mode |transmitted |enabled, |received | | |enabled, |data |send break |data to the| | |send no | |to remote |DTE | | |break to | |modem | | | |remote | | | | | |modem | | | | |----------+-----------+------------+------------+-----------| | i \K5 |Send break |Send break |Send break |Break sent | | |with |with |to remote |with | | |transmitted|transmitted |modem |received | | |data |data |immediately |data to the| | | | | |DTE | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | MNP5 disabled | |--------------+---------------------------------------------| | i %C1 | MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP reliable mode enabled | |--------------+---------------------------------------------| | i \N3 | V.42 auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | LAPM/Normal mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Modifier | Function | |--------------+---------------------------------------------| | P | Pulse dialing enabled | |--------------+---------------------------------------------| | R | Answer mode enabled, originate mode | | | disabled following handshake initiation | |--------------+---------------------------------------------| | S=n | Dial stored telephone number n=0-3 | |--------------+---------------------------------------------| | T | Tone dialing enabled | |--------------+---------------------------------------------| | W | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | , | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | ! | Modem commanded to go off-hook for | | | specified time before returning on-hook | |--------------+---------------------------------------------| | @ | Wait for quiet answer | |--------------+---------------------------------------------| | ; | Modem returned to command state after | | | dialing | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTE CONNECT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S112=n [cmds] | |--------------+---------------------------------------------| | Description: | Select the DTE speed during data transfer | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i S112=0 | Last AT speed | |-----------------------+------------------------------------| | S112=1 | Not used | |-----------------------+------------------------------------| | S112=2 | Sets DTE speed to 300bps | |-----------------------+------------------------------------| | S112=3 | Sets DTE speed to 1200bps | |-----------------------+------------------------------------| | S112=4 | Sets DTE speed to 2400bps | |-----------------------+------------------------------------| | S112=5 | Sets DTE speed to 4800bps | |-----------------------+------------------------------------| | S112=6 | Sets DTE speed to 7200bps | |-----------------------+------------------------------------| | S112=7 | Sets DTE speed to 9600bps | |-----------------------+------------------------------------| | S112=8 | Sets DTE speed to 12000bps | |-----------------------+------------------------------------| | S112=9 | Sets DTE speed to 14400bps | |-----------------------+------------------------------------| | S112=10 | Sets DTE speed to 16800bps | |-----------------------+------------------------------------| | S112=11 | Sets DTE speed to 19200bps | |-----------------------+------------------------------------| | S112=12 | Sets DTE speed to 38400bps | |-----------------------+------------------------------------| | S112=13 | Sets DTE speed to 57600bps | |-----------------------+------------------------------------| | S112=14 | Sets DTE speed to 600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bi-directional XON/XOFF flow control | | | enabled | |--------------+---------------------------------------------| | \Q2 | Unidirectional hardware flow control | | | enabled | |--------------+---------------------------------------------| | i \Q3 | Bi-directional hardware flow control | | | enabled (RTS/CTS) | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports ROM components | |--------------+---------------------------------------------| | I4 | Reports modem capabilities | +------------------------------------------------------------+