CONTROLWARE COMMUNICATIONS SYSTEMS, INC. ======================================== CITAM Card Type ISDN TA Chipset Unidentified ISDN Transfer Rate 56Kbps x 2/64Kbps x 2 ISDN Protocol V.110, X.75 Switch Type 1TR6, 5ESS, DMS100, DSS1, NI-1 Data Bus Serial +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------+--------+-----------------------+--------| | SELECT button | BT1 | ISDN S/T interface | CN1 | |------------------+--------+-----------------------+--------| | ENTER button | BT2 | LED display | LED | |------------------+--------+-----------------------+--------| | RESET button | BT3 | Header to interface | W1A | | | | board W1B | | |------------------------------------------------------------| | Note: Either CN1 or the ISDN interface on the | | installed interface board may be used, but not both. | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Configuration may be changed via | S1/1 | Off | | interface or front panel | | | |-----------------------------------------+-------+----------| | Configuration may be changed via front | S1/1 | On | | panel supervisor only | | | |-----------------------------------------+-------+----------| | i ISDN connects with standard dialing | S1/2 | Off | |-----------------------------------------+-------+----------| | ISDN connects with S0FV (leased-line) | S1/2 | On | |-----------------------------------------+-------+----------| | i 1TR6 Service Indicator set for data | S1/3 | Off | | transmission | | | |-----------------------------------------+-------+----------| | 1TR6 Service Indicator set for X.21 | S1/3 | On | | services | | | |-----------------------------------------+-------+----------| | i TA operates in synchronous mode | S1/4 | Off | |-----------------------------------------+-------+----------| | TA operates in asynchronous mode | S1/4 | On | |-----------------------------------------+-------+----------| | i Factory configured - do not alter | S1/5 | N/A | | (synchronous mode) | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS (CON'T) | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i AT command set enabled (asynchronous | S1/8 | On | | mode) | | | |-----------------------------------------+-------+----------| | V.25bis command set enabled | S1/8 | Off | | (asynchronous mode) | | | |-----------------------------------------+-------+----------| | i X.21 command set enabled (synchronous | S1/8 | On | | mode) | | | |-----------------------------------------+-------+----------| | V.25bis command set enabled | S1/8 | Off | | (synchronous mode) | | | |-----------------------------------------+-------+----------| | i Factory configured - do not alter | S2/1 | On | |-----------------------------------------+-------+----------| | i CD signal forced high | S2/6 | Off | |-----------------------------------------+-------+----------| | CD signal high when connection is | S2/6 | On | | synchronized | | | |-----------------------------------------+-------+----------| | i DSR signal forced high | S2/7 | Off | |-----------------------------------------+-------+----------| | DSR signal high when connection is | S2/7 | On | | synchronized | | | |-----------------------------------------+-------+----------| | i Unit is a table-top version | S2/8 | Off | |-----------------------------------------+-------+----------| | Unit is a rack mount version | s2/8 | On | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA FORMAT SELECTION (ASYNCHRONOUS MODE) | |------------------------------------------------------------| | Setting | S1/5 | S1/6 | S1/7 | |---------------------------------------+------+------+------| | 7 data bits, no parity, 1 stop bit | Off | On | On | |---------------------------------------+------+------+------| | 7 data bits, even parity, 1 stop bit | On | On | On | |---------------------------------------+------+------+------| | 8 data bits, no parity, 1 stop bit | On | On | Off | |---------------------------------------+------+------+------| | 8 data bits, even parity, 1 stop bit | Off | Off | On | |---------------------------------------+------+------+------| | 8 data bits, odd parity, 1 stop bit | On | Off | On | |---------------------------------------+------+------+------| | i 8 data bits, no parity, 2 stop bits | Off | Off | Off | |---------------------------------------+------+------+------| | 8 data bits, even parity, 2 stop bits | On | Off | Off | |---------------------------------------+------+------+------| | 8 data bits, odd parity, 2 stop bits | Off | On | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA FORMAT SELECTION (SYNCHRONOUS MODE) | |------------------------------------------------------------| | Setting | S1/6 | S1/7 | |---------------------------------------+----------+---------| | ASCII character set, BSC encoding | On | On | |---------------------------------------+----------+---------| | ASCII character set, HDLC encoding | Off | On | |---------------------------------------+----------+---------| | EBCDIC character set, BSC encoding | On | Off | |---------------------------------------+----------+---------| | i EBCDIC character set, HDLC encoding | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED | |------------------------------------------------------------| | Setting | S2/2 | S2/3 | S2/4 | S2/5 | |-----------------+----------+----------+----------+---------| | 300bps | Off | On | Off | On | |-----------------+----------+----------+----------+---------| | 600bps | On | Off | Off | On | |-----------------+----------+----------+----------+---------| | 1200bps | Off | Off | Off | On | |-----------------+----------+----------+----------+---------| | 2400bps | On | On | On | Off | |-----------------+----------+----------+----------+---------| | 4800bps | Off | On | On | Off | |-----------------+----------+----------+----------+---------| | 9600bps | On | Off | On | Off | |-----------------+----------+----------+----------+---------| | 19.2Kbps | Off | Off | On | Off | |-----------------+----------+----------+----------+---------| | 38.4Kbps | On | On | Off | Off | |-----------------+----------+----------+----------+---------| | 48Kbps | Off | On | Off | Off | |-----------------+----------+----------+----------+---------| | 56Kbps | On | Off | Off | Off | |-----------------+----------+----------+----------+---------| | i 64Kbps | Off | Off | Off | Off | |------------------------------------------------------------| | Note: Asynchronous speeds may range from 300bps to | | 38.4Kbps, while synchronous speeds may range from | | 1200bps to 64Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS SELECTION | |------------------------------------------------------------| | Setting | S3 | |--------------------------------------+---------------------| | EAZ 1 | Position 1 | |--------------------------------------+---------------------| | EAZ 2 | Position 2 | |--------------------------------------+---------------------| | EAZ 3 | Position 3 | |--------------------------------------+---------------------| | EAZ 4 | Position 4 | |--------------------------------------+---------------------| | EAZ 5 | Position 5 | |--------------------------------------+---------------------| | EAZ 6 | Position 6 | |--------------------------------------+---------------------| | EAZ 7 | Position 7 | |--------------------------------------+---------------------| | EAZ 8 | Position 8 | |--------------------------------------+---------------------| | TA is part of hunt group | Position 0 | |------------------------------------------------------------| | Note: When adapter is set for leased-line mode, the | | EAZ must be set to 2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |-----+--------+----------+----------------------------------| | S0 | Yellow | On | ISDN connection is active | |-----+--------+----------+----------------------------------| | S0 | Yellow | Blinking | ISDN connection has been made | | | | | but is not active | |-----+--------+----------+----------------------------------| | S0 | Yellow | Off | ISDN is not connected | |-----+--------+----------+----------------------------------| | P1 | Green | On | Port 1 is connected to ISDN | |-----+--------+----------+----------------------------------| | P1 | Green | Blinking | Port 1 has received an ISDN call | | | | | but has not connected | |-----+--------+----------+----------------------------------| | P1 | Green | Off | Port 1 is not connected to ISDN | |-----+--------+----------+----------------------------------| | P2 | Green | On | Port 2 is connected to ISDN | |-----+--------+----------+----------------------------------| | P2 | Green | Blinking | Port 2 has received an ISDN call | | | | | but has not connected | |-----+--------+----------+----------------------------------| | P2 | Green | Off | Port 2 is not connected to ISDN | |------------------------------------------------------------| | Note: P2 will have no function on models with only | | one port. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |--------------------+-------+-----------------------+-------| | Supervisor port | CN1 | DC power in | CN4 | |--------------------+-------+-----------------------+-------| | ISDN S/T interface | CN2 | Header to main board | W1B | | | | W1A | | |--------------------+-------+-----------------------+-------| | X.21 serial port | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P31 | Open | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P31 | Closed | | ground | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P28 | R3 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |--------------------+-------+-----------------------+-------| | Supervisor port | CN1 | X.21 serial port 2 | CN4 | |--------------------+-------+-----------------------+-------| | ISDN S/T interface | CN2 | DC power in | CN5 | |--------------------+-------+-----------------------+-------| | X.21 serial port 1 | CN3 | Header to main board | W1B | | | | W1A | | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P31 | Open | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P31 | Closed | | ground | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | PORT 1 RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P16 | R4 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | PORT 2 RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P17 | R5 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |--------------------+-------+-----------------------+-------| | Supervisor port | CN1 | DC power in | CN4 | |--------------------+-------+-----------------------+-------| | ISDN S/T interface | CN2 | Header to main board | W1B | | | | W1A | | |--------------------+-------+-----------------------+-------| | V.24 serial port | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P32 | Open | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P32 | Closed | | ground | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P1 | R4 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |-----------------------+-------+--------------------+-------| | Supervisor port | CN1 | V.24 serial port 1 | CN4 | | | | via DB-26 port | | |-----------------------+-------+--------------------+-------| | ISDN S/T interface | CN2 | DC power in | CN5 | |-----------------------+-------+--------------------+-------| | V.24 serial port 2 | CN3 | Header to main | W1B | | via DB-26 port | | board W1A | | |------------------------------------------------------------| | Note: Standard V.24 serial ports are provided on | | included adapter cables. | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P33 | Open | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P33 | Closed | | ground | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | PORT 1 RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P1 | R3 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | PORT 2 RECEIVER OPEN CIRCUIT FAILSAFE | |------------------------------------------------------------| | Setting | P2 | R4 | |------------------+--------------------+--------------------| | i Enabled | Not installed | Installed | |------------------+--------------------+--------------------| | Disabled | Installed | Not installed | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |--------------------+-------+-----------------------+-------| | Supervisor port | CN1 | DC power in | CN4 | |--------------------+-------+-----------------------+-------| | ISDN S/T interface | CN2 | Header to main board | W1B | | | | W1A | | |--------------------+-------+-----------------------+-------| | V.35 serial port | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P32 | Open | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P32 | Closed | | ground | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |-----------------------+-------+--------------------+-------| | Supervisor port | CN1 | V.35 serial port 1 | CN4 | | | | via DB-26 port | | |-----------------------+-------+--------------------+-------| | ISDN S/T interface | CN2 | DC power in | CN5 | |-----------------------+-------+--------------------+-------| | V.35 serial port 2 | CN3 | Header to main | W1B | | via DB-26 port | | board W1A | | |------------------------------------------------------------| | Note: Standard V.35 serial ports are provided on | | included adapter cables. | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-----------------------------------------+-------+----------| | i Signal ground not connected to | P32 | Closed | | chassis ground | | | |-----------------------------------------+-------+----------| | Signal ground connected to chassis | P32 | Open | | ground | | | +------------------------------------------------------------+ +--------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |--------------------------------------------------------| | Basic AT Commands | |--------------------------------------------------------| | +++, A/ | |--------------------------------------------------------| | A, E, H, O, Q, V, X, Z | |--------------------------------------------------------| | &D, &F, &V, &W, &Z | | | | %I | |--------------------------------------------------------| | S-Registers | |--------------------------------------------------------| | S0, S1, S2, S3, S4, S5 | |--------------------------------------------------------| | V.25bis Commands | |--------------------------------------------------------| | CIC, CRI, CRS, DIC, PRN | |--------------------------------------------------------| | Note: See MHI help file for complete information. | +--------------------------------------------------------+ +------------------------------------------------------------+ | UNIDENTIFIED COMMANDS | |------------------------------------------------------------| | Command | Default | |------------------------------+-----------------------------| | %L | 0 | |------------------------------+-----------------------------| | %M | 0 | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | ACCESS TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Kn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the type of access for this ISDN | | | line. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %K1 | Line is intermittent dial-up. | |--------------+---------------------------------------------| | %K2 | Line is semi-permanent dial-up. | |--------------+---------------------------------------------| | %K3 | Line is time-link dial-up. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ASYNC/SYNC MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the adapter is operating in | | | asynchronous or synchronous mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode selected. | |--------------+---------------------------------------------| | &M1 | Asynchronous command mode, synchronous data | | | mode at 600bps. | |--------------+---------------------------------------------| | &M2 | Asynchronous command mode, synchronous data | | | mode at 1200bps. | |--------------+---------------------------------------------| | &M3 | Asynchronous command mode, synchronous data | | | mode at 2400bps. | |--------------+---------------------------------------------| | &M4 | Asynchronous command mode, synchronous data | | | mode at 4800bps. | |--------------+---------------------------------------------| | &M5 | Asynchronous command mode, synchronous data | | | mode at 9600bps. | |--------------+---------------------------------------------| | &M6 | Asynchronous command mode, synchronous data | | | mode at 19.2Kbps. | |--------------+---------------------------------------------| | &M7 | Asynchronous command mode, synchronous data | | | mode at 38.4Kbps. | |--------------+---------------------------------------------| | &M8 | Asynchronous command mode, synchronous data | | | mode at 48Kbps. | |--------------+---------------------------------------------| | &M9 | Asynchronous command mode, synchronous data | | | mode at 56Kbps. | |--------------+---------------------------------------------| | &M10 | Asynchronous command mode, synchronous data | | | mode at 64Kbps. | |--------------+---------------------------------------------| | &M11 | Synchronous data mode at 64Kbps with byte | | | timing. | |--------------+---------------------------------------------| | &M13 | Synchronous data mode at 128Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK DELAY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %H=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the amount of time that the adapter | | | will wait after a call disconnects before | | | initiating a callback sequence. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects when the adapter will call back an | | | incoming call. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %G0 | Neither initiate nor allow callback | | | requests. | |--------------+---------------------------------------------| | %G1 | Do not initiate callbacks but allow | | | requests. | |--------------+---------------------------------------------| | %G2 | Initiate callbacks but do not allow | | | requests. | |--------------+---------------------------------------------| | %G3 | Initiate callbacks and allow requests. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALL BUNDLING SOURCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Jn [cmds] | |--------------+---------------------------------------------| | Description: | Selects which stored number the modem will | | | dial for the B2 channel when attempting | | | call bundling. Executing %J0 will use the | | | same number as was dialed for the B1 | | | channel. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &R0 | CTS follows RTS. | |--------------+---------------------------------------------| | &R1 | CTS forced high. | |--------------+---------------------------------------------| | &R2 | CTS controlled by remote; high when | | | connection is made at 48Kbps or less. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA FORMAT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the format of the data from the | | | serial port. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %N0 | 7 data bits, no parity, 1 stop bit. | |--------------+---------------------------------------------| | %N1 | 7 data bits, even parity, 1 stop bit. | |--------------+---------------------------------------------| | %N2 | 8 data bits, odd parity, 1 stop bit. | |--------------+---------------------------------------------| | %N3 | 8 data bits, even parity, 1 stop bit. | |--------------+---------------------------------------------| | i %N4 | 8 data bits, no parity, 1 stop bit. | |--------------+---------------------------------------------| | %N5 | 8 data bits, odd parity, 2 stop bits. | |--------------+---------------------------------------------| | %N6 | 8 data bits, even parity, 2 stop bits. | |--------------+---------------------------------------------| | %N7 | 8 data bits, no parity, 2 stop bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &C0 | DCD high when call is synchronized. | |--------------+---------------------------------------------| | &C1 | DCD forced high. | |--------------+---------------------------------------------| | &C2 | DCD controlled by remote; high when | | | connection is made at more than 48Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | adapter. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I | Displays complete identification. | |--------------+---------------------------------------------| | I0 | Displays information about the control | | | firmware. | |--------------+---------------------------------------------| | I1 | Displays information about the ISDN | | | firmware. | |--------------+---------------------------------------------| | I2 | Displays the version of the hardware. | |--------------+---------------------------------------------| | I3 | Displays information about the interface | | | board. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STATUS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Sn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the status of the indicated part | | | of the adapter. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %S | Display all information. | |--------------+---------------------------------------------| | %S0 | Display port status. | |--------------+---------------------------------------------| | %S1 | Display S0 status. | |--------------+---------------------------------------------| | %S2 | Display last ISDN error code in hex. | |--------------+---------------------------------------------| | %S3 | Display SPID 1. | |--------------+---------------------------------------------| | %S4 | Display SPID 2. | |------------------------------------------------------------| | DSR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &S0 | DSR high when connection is successful. | |--------------+---------------------------------------------| | &S1 | DSR forced high. | |--------------+---------------------------------------------| | &S2 | DSR controlled by remote; high when | | | connection is made at more than 48Kbps. | |--------------+---------------------------------------------| | &S3 | DSR high when connection is synchronized. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ISDN B-CHANNEL MAPPING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects how the adapter will map the | | | B-channel subaddresses. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %Q0 | B-channel mapping disabled. | |--------------+---------------------------------------------| | %Q1 | B-channel mapping enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects what speed the local serial port is | | | operating at in asynchronous mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %R0 | Set speed to 300bps. | |--------------+---------------------------------------------| | %R1 | Set speed to 600bps. | |--------------+---------------------------------------------| | %R2 | Set speed to 1200bps. | |--------------+---------------------------------------------| | %R3 | Set speed to 2400bps. | |--------------+---------------------------------------------| | %R4 | Set speed to 4800bps. | |--------------+---------------------------------------------| | i %R5 | Set speed to 9600bps. | |--------------+---------------------------------------------| | %R6 | Set speed to 19.2Kbps. | |--------------+---------------------------------------------| | %R7 | Set speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MATCH IN-BAND SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %An [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the adapter may switch to | | | match the in-band speed of the connection. | |--------------+---------------------------------------------| | Note: | This command has no effect in asynchronous | | | mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %A0 | Adapter may switch to lower speed. | |--------------+---------------------------------------------| | i %A1 | Adapter may not switch speed. | |--------------+---------------------------------------------| | %A2 | Adapter may switch to higher speed. | |--------------+---------------------------------------------| | %A3 | Adapter may switch to any speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MATCH BEARER SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the adapter may switch to | | | match the bearer speed of the connection. | |--------------+---------------------------------------------| | Note: | This command has no effect in asynchronous | | | mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %B0 | Adapter may switch to lower speed. | |--------------+---------------------------------------------| | i %B1 | Bearer speed matching disabled. | |--------------+---------------------------------------------| | %B2 | Adapter may switch to higher speed. | |--------------+---------------------------------------------| | %B3 | Adapter may switch to any speed. | |--------------+---------------------------------------------| | %B4 | Bearer speed matching enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD CHECKING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects when the adapter will require a | | | password for configuration changes. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %D0 | Require password for remote configuration | | | changes only. | |--------------+---------------------------------------------| | %D1 | Require password for all configuration | | | changes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT %C=xxxx | |--------------+---------------------------------------------| | Description: | Sets the password to a case-sensitive | | | string of up to ten characters. If no | | | string is entered the password is returned | | | to its default. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S8=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the bit rate adaptation protocol | | | the adapter will use. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S8=0 | Adapter will use X.30. | |--------------+---------------------------------------------| | S8=1 | Adapter will use V.110. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERVICE INDICATOR | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S6=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the 1TR6 Service Indicator. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S6=3 | 1TR6 Service Indicator set for data | | | transmission. | |--------------+---------------------------------------------| | S6=7 | 1TR6 Service Indicator set for X.21 | | | services. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S7=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the subaddress to a value from 1 to 8. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS COPYING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the adapter will copy the | | | subaddress to the call number. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %E0 | Subaddress copying disabled. | |--------------+---------------------------------------------| | %E1 | Subaddress copying enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS - SETUP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects which subaddress the adapter sends | | | during call setup. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %P0 | Adapter sends remote port subaddress. | |--------------+---------------------------------------------| | %P1 | Adapter sends local port subaddress. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS SOURCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %On [cmds] | |--------------+---------------------------------------------| | Description: | Selects the source of the subaddress sent | | | to the remote system. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %O0 | Taken from call number string. | |--------------+---------------------------------------------| | %O1 | Global call sent in-band. | |--------------+---------------------------------------------| | %O2 | Stored port subaddress sent in-band. | |--------------+---------------------------------------------| | %O3 | Stored port subaddress sent in-band and | | | during call setup. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCH TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the switch type the adapter is | | | connected to. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %F0 | Adapter is connected to National NI-1 | | | switch. | |--------------+---------------------------------------------| | %F1 | Adapter is connected to AT&T 5E6 switch. | |--------------+---------------------------------------------| | %F2 | Adapter is connected to AT&T 5E8 switch. | |--------------+---------------------------------------------| | %F3 | Adapter is connected to Northern Telecom | | | DMS-100 switch. | +------------------------------------------------------------+ Proprietary V.25bis Command Set +------------------------------------------------------------+ | CALL REQUESTED NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | CRN<#> | |--------------+---------------------------------------------| | Description: | Dials the number given; it will ignore | | | spaces and hyphens in the string; if the | | | string is more than fifty characters long, | | | a result of INV will be returned. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | CRN<#>*n | Dials the number indicated and requests | | | subaddress n. | |--------------+---------------------------------------------| | CRN<#>/n | Dials the number indicated and requests | | | subaddress n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO4;n | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i PRO4;0 | CTS follows RTS. | |--------------+---------------------------------------------| | PRO4;1 | CTS forced high. | |--------------+---------------------------------------------| | PRO4;2 | CTS controlled by remote; high when | | | connection is made at 48Kbps or less. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO6;n | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i PRO6;0 | DCD high when call is synchronized. | |--------------+---------------------------------------------| | PRO6;1 | DCD forced high. | |--------------+---------------------------------------------| | PRO6;2 | DCD controlled by remote; high when | | | connection is made at more than 48Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY COMMAND SETTING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLO n | |--------------+---------------------------------------------| | Description: | Displays the setting of the indicated | | | option set with PROn; the adapter will | | | respond with LSOn;a where a is the setting. | | | Two values may be displayed that may not be | | | set with PROn. They are listed below. If no | | | value is given all options are listed. | |------------------------------------------------------------| | Command | Value | Meaning | |-----------------+----------+-------------------------------| | RLO 8 | 0 | Terminal is in asynchronous | | | | mode. | |-----------------+----------+-------------------------------| | | 1 | Terminal is in synchronous | | | | mode. | |-----------------+----------+-------------------------------| | RLO 9 | 3 | 1TR6 Service Indicator set | | | | for data transmission. | |-----------------+----------+-------------------------------| | | 7 | 1TR6 Service Indicator set | | | | for X.21 services. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY STORED NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | RLN n | |--------------+---------------------------------------------| | Description: | Displays the telephone number stored in | | | memory location n. If no location is | | | specified, all stored numbers are listed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO5;n | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i PRO5;0 | DSR high when connection is successful. | |--------------+---------------------------------------------| | PRO5;1 | DSR forced high. | |--------------+---------------------------------------------| | PRO5;2 | DSR controlled by remote; high when | | | connection is made at more than 48Kbps. | |--------------+---------------------------------------------| | PRO5;3 | DSR high when connection is synchronized. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ECHO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO2;n | |--------------+---------------------------------------------| | Description: | Selects whether the modem will echo data | | | received from the DTE back. | |--------------+---------------------------------------------| | Note: | This command has no effect in synchronous | | | mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | PRO2;0 | Echo disabled. | |--------------+---------------------------------------------| | i PRO2;1 | Echo enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INCOMING CALL INFORMATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO7;n | |--------------+---------------------------------------------| | Description: | Selects whether the INC message is V.25bis | | | standard or displays extra information. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | PRO7;0 | INC message is V.25bis standard. | |--------------+---------------------------------------------| | PRO7;1 | INC message displays extra information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | PRO3;n | |--------------+---------------------------------------------| | Description: | Selects the bit rate adaptation protocol | | | the adapter will use. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | PRO3;0 | Adapter will use X.30. | |--------------+---------------------------------------------| | PRO3;1 | Adapter will use V.110. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TO SWITCH DEFAULTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | PRO0;0 | |--------------+---------------------------------------------| | Description: | Resets the configuration of the adapter to | | | the settings of S1, S2, and S3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUBADDRESS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PRO1;n | |--------------+---------------------------------------------| | Description: | Sets the subaddress to a value from 1 to 8. | +------------------------------------------------------------+