CARDINAL TECHNOLOGIES, INC. =========================== MVP34ISP Card Type Modem/Fax card Chip Set Unidentified I/O Options Line in, line out, microphone jack, speaker jack Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V34, V.32bis, V.32, V.22bis, V.22, V.21 Fax Modulation ITU-T V.17, V.27ter, V.29, V.21 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 16-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | RJ-11 line in | CN1 | Microphone jack | CN3 | |-------------------------+---------+-----------------+------| | RJ-11 line out | CN2 | Speaker jack | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting |JP1/A |JP1/B |JP1/C |JP1/D |JP1/E |JP1/F | |------------------+------+------+------+------+------+------| | COM1 (3F8h) |Closed| Open | Open | Open | Open | Open | |------------------+------+------+------+------+------+------| | COM2 (2F8h) | Open |Closed| Open | Open | Open | Open | |------------------+------+------+------+------+------+------| | COM3 (3E8h) | Open | Open |Closed| Open | Open | Open | |------------------+------+------+------+------+------+------| | COM4 (2E8h) | Open | Open | Open |Closed| Open | Open | |------------------+------+------+------+------+------+------| | i Plug & Play | Open | Open | Open | Open |Closed|Closed| | enabled | | | | | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | Setting |JP2/A |JP2/B |JP2/C |JP2/D |JP2/E |JP2/F | |------------------+------+------+------+------+------+------| | IRQ3 | Open | Open | Open | Open | Open |Closed| |------------------+------+------+------+------+------+------| | IRQ4 | Open | Open | Open | Open |Closed| Open | |------------------+------+------+------+------+------+------| | IRQ5 | Open | Open | Open |Closed| Open | Open | |------------------+------+------+------+------+------+------| | IRQ7 | Open | Open |Closed| Open | Open | Open | |------------------+------+------+------+------+------+------| | IRQ10 | Open |Closed| Open | Open | Open | Open | |------------------+------+------+------+------+------+------| | IRQ11 |Closed| Open | Open | Open | Open | Open | |------------------+------+------+------+------+------+------| | i Plug & Play | Open | Open | Open | Open | Open | Open | | enabled | | | | | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, +++, A/ | |------------------------------------------------------------| | A, B, E, H, M, O, P, Q, T, V, W, Y, Z | |------------------------------------------------------------| | &C, &G, &P, &S, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \G, \K, \N, | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | +MS | |------------------------------------------------------------| | #CID | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, | |------------------------------------------------------------| | S23, S24, S25, S26, S27, S29, S30, S31, S32, S33, S38, | | S39, S40, S41, S95 | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled; handshake | | | begins at line speed designated by the S37 | | | register. | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | i &D2 | Normal DTR operations | |--------------+---------------------------------------------| | &D3 | Resets on receipt of DTR | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D"WXY" | Optional method of denoting telephone | | | numbers. Letters enclosed in quotes are | | | interpreted as numbers according to the | | | system found on a telephone keypad. | |--------------+---------------------------------------------| | D* | The star digit (touch tone only) | |--------------+---------------------------------------------| | D# | The gate digit (touch tone only) | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D/ | Delays 125 ms. Before proceeding with dial | | | string | |--------------+---------------------------------------------| | D^ | Calling tone enable/disable for current | | | call only | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | |--------------+---------------------------------------------| | D& | Waiting for AT&T "bong" tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables flow control | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | Hardware, RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | Software, XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent software, XON/XOFF flow control | | | enabled | |--------------+---------------------------------------------| | &K6 | Software & hardware flow control enabled | |------------------------------------------------------------| | Note: Default setting for fax operations is &K6 | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports four digit product code | |--------------+---------------------------------------------| | I1 | Reports firmware checksum | |--------------+---------------------------------------------| | I2 | Verify checksum | |--------------+---------------------------------------------| | I3 | Reports firmware revision | |--------------+---------------------------------------------| | I4 | Reports identifier string | |--------------+---------------------------------------------| | I5 | Reports country code | |--------------+---------------------------------------------| | I6 | Reports data pump modem and revision | +------------------------------------------------------------+ +------------------------------------------------------------+ | SELECT CALL PROGRESS RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Xn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of tone detection and | | | associated result code format options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | X0 | Busy and dial tone detection disabled; | | | extended result codes diabled. | |--------------+---------------------------------------------| | X1 | Busy and dial tone detection disabled; | | | extended result codes enabled. | |--------------+---------------------------------------------| | X2 | Busy tone detection disabled, dial tone | | | detection enabled; extended result codes | | | enabled. | |--------------+---------------------------------------------| | X3 | Busy tone detection enabled, dial tone | | | detection disabled; extended result codes | | | enabled. | |--------------+---------------------------------------------| | X4 | Busy and dial tone detection enabled; | | | extended result codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | i L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ AT VOICE COMMAND SET +------------------------------------------------------------+ | AUDIO MODULATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SQS=x,y [cmds] | |--------------+---------------------------------------------| | Description: | Selects data speed with audio modulation; | | | enable/disable automode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i x=0 | V.61 modulation enabled (4800bps) | |--------------+---------------------------------------------| | x=1 | V61+ modulation enabled (4800bps - 9600bps) | |--------------+---------------------------------------------| | x=2 | V34Q modulation enabled (4800bps - | | | 14.4Kbps) | |--------------+---------------------------------------------| | y=0 | Automode disabled | |--------------+---------------------------------------------| | i y=1 | Automode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUDIOSPAN MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SMS=x,y,z [cmds] | |--------------+---------------------------------------------| | Description: | Selects audiospan modem; selects voice and | | | data speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i x=0 | Audiospan disabled/data only | |--------------+---------------------------------------------| | x=1 | Reserved | |--------------+---------------------------------------------| | x=2 | Audiospan enabled | |--------------+---------------------------------------------| | y=4800 | Minimum voice+data speed set to 4800bps | |--------------+---------------------------------------------| | y=7200 | Minimum voice+data speed set to 7200bps | |--------------+---------------------------------------------| | y=9600 | Minimum voice+data speed set to 9600bps | |--------------+---------------------------------------------| | y=12000 | Minimum voice+data speed set to 12.0Kbps | |--------------+---------------------------------------------| | y=14400 | Minimum voice+data speed set to 14.4Kbps | |--------------+---------------------------------------------| | z=4800 | Maximum voice+data speed set to 4800bps | |--------------+---------------------------------------------| | z=7200 | Maximum voice+data speed set to 7200bps | |--------------+---------------------------------------------| | z=9600 | Maximum voice+data speed set to 9600bps | |--------------+---------------------------------------------| | z=12000 | Maximum voice+data speed set to 12.0Kbps | |--------------+---------------------------------------------| | z=14400 | Maximum voice+data speed set to 14.4Kbps | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA BURST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SMCn [cmds] | |--------------+---------------------------------------------| | Description: | Data burst enable/disable. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | SMC0 | Data burst disabled; audio channel open at | | | all times during connection | |--------------+---------------------------------------------| | i SMC1 | Data burst enabled; audio channel open only | | | when data is detected on network | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |-----------------+------------------------------------------| | Default: | Unidentified | |-----------------+------------------------------------------| | Range: | 0 - 255 | |-----------------+------------------------------------------| | Description: | Selects which distinctive ring signals | | | the modem will respond to. | |------------------------------------------------------------| | Bit | Value | Function | |-----------+-------+----------------------------------------| | 0 | 0 | Distinctive ring disabled | |-----------+-------+----------------------------------------| | 1 | 0 | Distinctive ring type 1 disabled. | | | | | | | 1 | Distinctive ring type 1enabled. | |-----------+-------+----------------------------------------| | 2 | 0 | Distinctive ring type 2disabled | | | | | | | 1 | Distinctive ring type 2 enabled. | |-----------+-------+----------------------------------------| | 3 | 0 | Distinctive ring types 1 & 2 disabled. | | | | | | | 1 | Distinctive ring types 1 & 2 enabled. | |-----------+-------+----------------------------------------| | 4 | 0 | Distinctive ring type 3 disabled. | | | | | | | 1 | Distinctive ring type 3 enabled. | |-----------+-------+----------------------------------------| | 5 | 0 | Distinctive ring types 1 & 3 disabled. | | | | | | | 1 | Distinctive ring types 1 & 3 enabled. | |-----------+-------+----------------------------------------| | 6 | 0 | Distinctive ring types 2 & 3 disabled. | | | | | | | 1 | Distinctive ring types 2 & 3 enabled. | |-----------+-------+----------------------------------------| | 7 | 0 | Distinctive ring types 1, 2 & 3 | | | | disabled. | | | 1 | | | | | Distinctive ring types 1, 2 & 3 | | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10EC | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SECn, [] [cmds] | |--------------+---------------------------------------------| | Range (tx | 0-30dBm | | level) | | |--------------+---------------------------------------------| | Description: | Enable/disable MNP10EC | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i -SEC0 | MNP10EC disabled | |--------------+---------------------------------------------| | -SEC1 [] | will be defined by | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE DEVICE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the I/O device for the DSP chip. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #VLS=0 | Telephone line and handset used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=1 | Speakerphone used for voice I/O. | +------------------------------------------------------------+ S(STATUS) -REGISTERS +------------------------------------------------------------+ | CONNECTION FAILURE CODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S86? [cmds] | |--------------+---------------------------------------------| | Description: | Reports codes which correspond to the | | | possible causes of a connection failure | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 00 | Normal hang up | |--------------+---------------------------------------------| | 04 | Carrier signal lost | |--------------+---------------------------------------------| | 05 | V.42 negotiation failed to detect an EC | | | modem | |--------------+---------------------------------------------| | 09 | No common protocol found | |--------------+---------------------------------------------| | 12 | No failure - remote modem disconnected | | | normally | |--------------+---------------------------------------------| | 13 | Remote modem failed to respond after 10 | | | re-transmissions same message | |--------------+---------------------------------------------| | 14 | Violation of negotiated protocol caused | | | failure | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S37=0 | Speed of last connection | |--------------+---------------------------------------------| | S37=1 | Reserved | |--------------+---------------------------------------------| | S37=2 | Reserved | |--------------+---------------------------------------------| | S37=3 | 300bps | |--------------+---------------------------------------------| | S37=4 | Reserved | |--------------+---------------------------------------------| | S37=5 | 1200bps, V.22 | |--------------+---------------------------------------------| | S37=6 | 2400bps, V.22bis | |--------------+---------------------------------------------| | S37=7 | 1200/75bps, V.23 | |--------------+---------------------------------------------| | S37=8 | 4800bps, V.32bis/V.32 | |--------------+---------------------------------------------| | S37=9 | 9600bps, V.32bis/V.32 | |--------------+---------------------------------------------| | S37=10 | 12.0Kbps, V.32bis | |--------------+---------------------------------------------| | S37=11 | 14.4Kbps, V.32bis | |--------------+---------------------------------------------| | S37=12 | 7200bps, V.32bis | +------------------------------------------------------------+ +------------------------------------------------------------+ | ERROR CORRECTION/COMPRESSION | |------------------------------------------------------------| | Type: | Register | |------------------------------------------------------------| | Format: | AT [cmds] S46=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active error correction and | | | compression protocols | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | S46=136 | LAP-M only, no compression | |---------------+--------------------------------------------| | S46=138 | LAP-M with V.42bis data compression | +------------------------------------------------------------+ +------------------------------------------------------------+ | ERROR CORRECTION NEGOTIATION | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S36=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the action of the modem if it fails | | | to connect with the error-correction | | | protocol set in &Q. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S36=0 | Hang up | |--------------+---------------------------------------------| | S36=1 | Attempt a direct connection | |--------------+---------------------------------------------| | S36=3 | Attempt a buffered connection | |--------------+---------------------------------------------| | S36=4 | Attempt a connection at MNP2-4; if that | | | fails, hang up. | |--------------+---------------------------------------------| | S36=5 | Attempt a connection at MNP2-4; if that | | | fails, attempt a direct connection. | |--------------+---------------------------------------------| | S36=6 | Reserved | |--------------+---------------------------------------------| | S36=7 | Attempt a connection at MNP2-4; if that | | | fails, attempt a buffered connection. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FEATURE NEGOTIATION OPTIONS | |------------------------------------------------------------| | Type: | Register | |------------------------------------------------------------| | Format: | AT [cmds] S48=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active error correction and | | | compression protocols | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | S48=0 | Detection negotiation disabled, XID | | | negotiation disabled | |---------------+--------------------------------------------| | S48=7 | Fall-back to options set in S36 | +------------------------------------------------------------+