DIGICOM SPA =========== RAFFAELLO 28.8 Card Type Modem Chip Set Unidentified I/O Options RJ-11 line, 25-pin serial port, power Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22, V.22bis,V.23, V.32, V.32bis, V.34 Fax Modulation V.17, V.29, V.27ter, V.21 CH2 Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus External +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | RJ-11 line | CN1 | Power | CN3 | |----------------------------+---------+--------------+------| | 25-pin serial port | CN2 | Power switch | SW1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |-----+--------------+--------+------------------------------| | PWR | Unidentified | On | Power is on | |-----+--------------+--------+------------------------------| | PWR | Unidentified | Off | Power is off | |-----+--------------+--------+------------------------------| | DTR | Unidentified | On | Computer is ready | |-----+--------------+--------+------------------------------| | DTR | Unidentified | Off | Computer is not ready | |-----+--------------+--------+------------------------------| | SD | Unidentified | On | Modem is transmitting data | |-----+--------------+--------+------------------------------| | SD | Unidentified | Off | Modem is not transmitting | | | | | data | |-----+--------------+--------+------------------------------| | RD | Unidentified | On | Modem is receiving data | |-----+--------------+--------+------------------------------| | RD | Unidentified | Off | Modem is not receiving data | |-----+--------------+--------+------------------------------| | DCD | Unidentified | On | Network connection | | | | | established | |-----+--------------+--------+------------------------------| | DCD | Unidentified | Off | Network connection not | | | | | established | |-----+--------------+--------+------------------------------| | OH | Unidentified | On | Modem is off hook | |-----+--------------+--------+------------------------------| | OH | Unidentified | Off | Modem is on hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, E, H, L, M, O, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &P, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT commands | |------------------------------------------------------------| | \A, \B, \G, \K, \L, \N | |------------------------------------------------------------| | %C, %E, %L | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, | | S25, S26, S30, S32, S33, S95 | |------------------------------------------------------------| | Special commands | |------------------------------------------------------------| | +MS, -K, )M | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | i &D2 | Normal DTR operations | |--------------+---------------------------------------------| | &D3 | Resets on receipt of DTR | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D@ | Wait for Quiet Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by 5 seconds of | | | silence. | |--------------+---------------------------------------------| | D, | Dialing paused | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &F0 | Factory default profile 0 | |--------------+---------------------------------------------| | &F1 | Factory default profile 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS & XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product name | |--------------+---------------------------------------------| | I1 | Reports firmware release | |--------------+---------------------------------------------| | I2 | Reports memory test | |--------------+---------------------------------------------| | I3 | Reports product name | |--------------+---------------------------------------------| | I4 | Reports firmware release | |--------------+---------------------------------------------| | I5 | Reports active Country Code | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &R0 | CTS is off during handshake only | |--------------+---------------------------------------------| | i &R1 | CTS forced high | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | ABORT KEY CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enable/disable abort key during dialing | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %K0 | Abort key during dialing enabled | |--------------+---------------------------------------------| | %K1 | abort key during dialing disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR WINK | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %S [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates line signal | | | quality | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %S0 | Data set ready in accordance with &S | |--------------+---------------------------------------------| | %S1 | When DTR is forced high, and the modem is | | | goes off-hook, DTR is off for 1sec. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAKE BUSY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Make busy (off-hook) if DTR lost | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %B0 | Make busy disabled | |--------------+---------------------------------------------| | %B1 | Make busy enabled if S25=0. When DTR is | | | low, the modem goes off-hook | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.23 MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects V.23 split-speed and half-duplex | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | %F0 | V.23 mode disabled | |--------------------+---------------------------------------| | %F1 | 75bps receive, 1200bps transmit | |--------------------+---------------------------------------| | %F2 | 75bps transmit, 1200bps receive | +------------------------------------------------------------+ SPECIAL COMMANDS +------------------------------------------------------------+ | MNP10 - LINK NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed at which MNP10 link | | | negotiation will occur | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *H0 | Link will be negotiated at highest possible | | | speed | |--------------+---------------------------------------------| | *H1 | Link will be negotiated at 1200bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE SECURITY CODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *C [cmds] | |--------------+---------------------------------------------| | Description: | Executes security code feature of remote | | | setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE SETTING | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *R [cmds] | |--------------+---------------------------------------------| | Description: | Remote setting is available if the function | | | is enabled and MNP connection is enabled | +------------------------------------------------------------+ S(status) REGISTERS +------------------------------------------------------------+ | TRANSMISSION LEVEL - FAX | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S92=n [cmds] | |--------------+---------------------------------------------| | Range: | 3-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in fax mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - LEASED-LINE | |------------------------------------------------------------| | Type | Register or Configuration | |-------------+----------------------------------------------| | Format | AT [cmds] S91=n [cmds] | |-------------+----------------------------------------------| | Range | 3-15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal level for transmission over | | | leased-lines | +------------------------------------------------------------+