DIGICOM SPA =========== LEONARDO 33.6, LEONARDO 33.6 MAC Card Type Modem Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation ITU-T V.21, V.22, V.22bis,V.23, V.32, Protocol V.32bis, V.34 Fax Modulation V.17, V.29, V.27ter Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus PCMCIA 54981 +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, E, H, L, M, O, P, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &P, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT commands | |------------------------------------------------------------| | \A, \B, \K, \N | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, | | S29, S30, S32, S33, S95 | |------------------------------------------------------------| | Special commands | |------------------------------------------------------------| | +MS, -K | |------------------------------------------------------------| | | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | i &Q5 | Error correction mode | |--------------+---------------------------------------------| | &Q6 | Buffered asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | i &D2 | Normal DTR operations | |--------------+---------------------------------------------| | &D3 | Resets on receipt of DTR | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by 5 seconds of | | | silence | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | |--------------+---------------------------------------------| | D^ | Toggle calling tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &F0 | Factory default profile 0 | |--------------+---------------------------------------------| | &F1 | Factory default profile 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS and XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports maximum line speed | |--------------+---------------------------------------------| | I1 | Reports product type | |--------------+---------------------------------------------| | I2 | Reports checksum firmware | |--------------+---------------------------------------------| | I3 | Reports product name | |--------------+---------------------------------------------| | I4 | Reports firmware release | |--------------+---------------------------------------------| | I5 | Reports active Country Code | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Selects RTS/CTS options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &R0 | In asynchronous mode, C106 is controlled | | | according to V.25 handshake recommendation | |--------------+---------------------------------------------| | i &R1 | In synchronous mode, C106 follows flow | | | control | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | LINE SIGNAL QUALITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Q [cmds] | |--------------+---------------------------------------------| | Range: | 000-127 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Returns a value which indicates line signal | | | quality | +------------------------------------------------------------+ SPECIAL COMMANDS +------------------------------------------------------------+ | MNP10 - POWER LEVEL ADJUST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SEC=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-30 | |--------------+---------------------------------------------| | Unit: | -1dBm | |--------------+---------------------------------------------| | Description: | Controls automatic transmit power level | | | adjustment during MNP 10 link negotiation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SEC=0 | MNP10 disabled. Transmission level is set | | | in the S91 register | |--------------+---------------------------------------------| | -SEC=1, | MNP10 enabled. Set transmit level | | [tx_lev] | | +------------------------------------------------------------+ S(status) REGISTERS +------------------------------------------------------------+ | TRANSMISSION LEVEL - FAX | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S92=n [cmds] | |--------------+---------------------------------------------| | Range: | 3-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in fax mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - LEASED-LINE | |------------------------------------------------------------| | Type | Register or Configuration | |-------------+----------------------------------------------| | Format | AT [cmds] S91=n [cmds] | |-------------+----------------------------------------------| | Range | 3-15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal level for transmission over | | | leased-lines |