OLICOM, INC. ============ OC-7111 Card Type Fax, Modem (asynchronous) Chip Set Unidentified Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, MNP10, V.42, V.42bis Correction/Compression V1942 +------------------------------------------------------------+ | MISCELLANEOUS TECHNICAL NOTES | |------------------------------------------------------------| | Note: Due to country specific parameters, S-register | | settings are unidentified. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTOSYNC(TM) | |------------------------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-30 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Sets options for Hayes AutoSync(TM) functions. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used. | |------+-------+---------------------------------------------| | 1 | 0 | BSC enabled. | | | | | | | 1 | HDLC enabled. | |------+-------+---------------------------------------------| | 2 | 0 | HDLC address detection disabled. | | | | | | | 1 | HDLC address detection enabled. | |------+-------+---------------------------------------------| | 3 | 0 | NRZI bit encoding enabled. | | | | | | | 1 | NRZ2 bit encoding enabled. | |------+-------+---------------------------------------------| | 4 | 0 | Mark idle enabled. | | | | | | | 1 | Flag or sync idle enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOSYNC HDLC ADDRESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the HDLC address/BSC character | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | |--------------+---------------------------------------------| | %E2 | Auto-fallback/fall-forward enabled | |--------------+---------------------------------------------| | %E3 | Auto-retrain enabled with fast hang-up | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT MAPPED REGISTERS | |------------------------------------------------------------| | Register | Default | |----------------------------+-------------------------------| | S14 | Unidentified | |----------------------------+-------------------------------| | S21 | Unidentified | |----------------------------+-------------------------------| | S22 | Unidentified | |----------------------------+-------------------------------| | S23 | Unidentified | |----------------------------+-------------------------------| | S27 | Unidentified | |----------------------------+-------------------------------| | S28 | Unidentified | |----------------------------+-------------------------------| | S31 | Unidentified | |----------------------------+-------------------------------| | S40 | Unidentified | |----------------------------+-------------------------------| | S41 | Unidentified | |----------------------------+-------------------------------| | S201 | Unidentified | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Bn [cmds] | |--------------+---------------------------------------------| | Default: | 3 | |--------------+---------------------------------------------| | Range: | 1-9 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sends break to modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |---------------------+--------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |---------------------+--------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Break from | Modem receives | Break received | | | DTE | \B | from remote | | | | | modem | |-----------+--------------+----------------+----------------| | \K0 | Online | Break sent to | Buffers | | | command mode | remote modem | cleared, break | | | enabled, | and buffered | sent to DTE | | | send no | cleared | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K1 | Break sent | Break sent to | Buffers | | | to remote | remote modem | cleared, break | | | modem and | and buffered | sent to DTE | | | buffered | cleared | | | | cleared | | | |-----------+--------------+----------------+----------------| | \K2 | Online | Send break to | Break sent | | | command mode | remote modem | immediately to | | | enabled, | immediately | DTE | | | send no | | | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | \K3 | Send break | Send break to | Break sent | | | to remote | remote modem | immediately to | | | modem | immediately | DTE | | | immediately | | | |-----------+--------------+----------------+----------------| | \K4 | Online | Send break | Break sent | | | command mode | with | with received | | | enabled, | transmitted | data to the | | | send no | data | DTE | | | break to | | | | | remote modem | | | |-----------+--------------+----------------+----------------| | i \K5 | Send break | Send break | Break sent | | | with | with | with received | | | transmitted | transmitted | data to the | | | data | data | DTE | +------------------------------------------------------------+ +------------------------------------------------------------+ | COUNTRY CODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *NCnn [cmds] | |--------------+---------------------------------------------| | Description: | Select a country code from NVRAM (nn=00-08) | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DJ | Link will be negotiated at 1200bps for | | | current call only | |--------------+---------------------------------------------| | DK | Power level adjustment enabled for current | | | call only | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DR | Accepted but not used. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D@ | Wait for Quiet Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D; | Modem returned to command state after | | | dialing. The semicolon can only be placed | | | at the end of the dial command. | |--------------+---------------------------------------------| | D^ | Calling tone enabled/disabled for current | | | dialing attempt | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIALING CODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Zn [cmds] | |--------------+---------------------------------------------| | Description: | Select the dial code for pulse dialing | |------------------------------------------------------------| | Command | Function | |---------------------------+--------------------------------| | i *Z0 | Use dial code 0 | |---------------------------+--------------------------------| | *Z1 | Use dial code 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DELAYED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *B [cmds] | |--------------+---------------------------------------------| | Description: | Displays delayed numbers list | +------------------------------------------------------------+ +------------------------------------------------------------+ | DELAYED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *D [cmds] | |--------------+---------------------------------------------| | Description: | Displays delayed numbers list | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | |--------------+---------------------------------------------| | %C2 | V.42bis enabled | |--------------+---------------------------------------------| | i %C3 | MNP5 and V.42bis enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP reliable mode enabled | |--------------+---------------------------------------------| | i \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | MNP auto-reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLASH DIAL MODIFIER TIME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S29=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Time the modem will go on-hook upon | | | receiving the ! dial modifier in dial | | | string. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem port flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \G0 | Flow control disabled | |--------------+---------------------------------------------| | \G1 | Flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XOFF | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S33=n [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XOFF | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL CHARACTER - XON | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S32=n [cmds] | |--------------+---------------------------------------------| | Default: | 17 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used to represent XON | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %L [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates the | | | received line signal level | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL QUALITY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Q [cmds] | |--------------+---------------------------------------------| | Description: | Returns a value which indicates line signal | | | quality | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \J0 | Serial speed locked | |--------------+---------------------------------------------| | \J1 | Serial speed follows connect speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | MNP block size is 64 characters | |--------------+---------------------------------------------| | i \A1 | MNP block size is 128 characters | |--------------+---------------------------------------------| | \A2 | MNP block size is 192 characters | |--------------+---------------------------------------------| | \A3 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION SELECTION DISPLAY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +MS? [cmds] | |--------------+---------------------------------------------| | Description: | Displays modulation, automode, minimum rate | | | and maximum rate settings | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | +MS=? | Displays supported mode selection | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODULATION SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +MS=x,y,z,a [cmds] | |--------------+---------------------------------------------| | Description: | Sets options for active protocol; the | | | transfer rates specified by z and a must be | | | valid for the protocol selected. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | x=0 | V.21 | |--------------+---------------------------------------------| | x=1 | V.22 | |--------------+---------------------------------------------| | x=2 | V.22bis | |--------------+---------------------------------------------| | x=3 | V.23 | |--------------+---------------------------------------------| | x=9 | V.32 | |--------------+---------------------------------------------| | x=10 | V.32bis | |--------------+---------------------------------------------| | x=11 | V.34 | |--------------+---------------------------------------------| | x=64 | Bell 103 | |--------------+---------------------------------------------| | x=69 | Bell 212A | |--------------+---------------------------------------------| | x=74 | V.FC | |--------------+---------------------------------------------| | y=0 | Automode disabled | |--------------+---------------------------------------------| | y=1 | Auto-detect highest speed enabled | |--------------+---------------------------------------------| | z, a=300 | Set minimum or maximum transfer rate at | | | 300bps, respectively. | |--------------+---------------------------------------------| | z, a=1200 | Set minimum or maximum transfer rate at | | | 1200bps, respectively. | |--------------+---------------------------------------------| | z, a=2400 | Set minimum or maximum transfer rate at | | | 2400bps, respectively. | |--------------+---------------------------------------------| | z, a=4800 | Set minimum or maximum transfer rate at | | | 4800bps, respectively. | |--------------+---------------------------------------------| | z, a=7200 | Set minimum or maximum transfer rate at | | | 7200bps, respectively. | |--------------+---------------------------------------------| | z, a=9600 | Set minimum or maximum transfer rate at | | | 9600bps, respectively. | |--------------+---------------------------------------------| | z, a=12000 | Set minimum or maximum transfer rate at | | | 12000bps, respectively. | |--------------+---------------------------------------------| | z, a=14400 | Set minimum or maximum transfer rate at | | | 14400bps, respectively. | |--------------+---------------------------------------------| | z, a=16800 | Set minimum or maximum transfer rate at | | | 16800bps, respectively. | |--------------+---------------------------------------------| | z, a=19200 | Set minimum or maximum transfer rate at | | | 19200bps, respectively. | |--------------+---------------------------------------------| | z, a=21600 | Set minimum or maximum transfer rate at | | | 21600bps, respectively. | |--------------+---------------------------------------------| | z, a=24000 | Set minimum or maximum transfer rate at | | | 24000bps, respectively. | |--------------+---------------------------------------------| | z, a=26400 | Set minimum or maximum transfer rate at | | | 26400bps, respectively. | |--------------+---------------------------------------------| | z, a=28800 | Set minimum or maximum transfer rate at | | | 28800bps, respectively. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP - EXTENDED SERVICES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Kn [cmds] | |--------------+---------------------------------------------| | Description: | Selects MNP extended services | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i -K0 | MNP extended services disabled | |--------------+---------------------------------------------| | -K1 | MNP extended services enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP - STREAM/BLOCK MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects the transfer mode for MNP link | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \L0 | Stream mode for MNP enabled | |--------------+---------------------------------------------| | \L1 | Block mode for MNP enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - FALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Qn [cmds] | |--------------+---------------------------------------------| | Description: | Allows MNP10 to fall back to speeds slower | | | than 4800bps | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -Q0 | MNP10 at 2400 and 1200bps enabled | |--------------+---------------------------------------------| | -Q1 | MNP10 at 2400 and 1200bps disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - LINK NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed at which MNP10 link | | | negotiation will occur | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | *H0 | Link will be negotiated at highest possible | | | speed | |--------------+---------------------------------------------| | *H1 | Link will be negotiated at 1200bps | |--------------+---------------------------------------------| | *H2 | Link will be negotiated at 4800bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - POWER LEVEL ADJUST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] )Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls automatic transmit power level | | | adjustment during MNP 10 link negotiation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i )M0 | Power level adjustment disabled | |--------------+---------------------------------------------| | )M1 | Power level adjustment enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Calculates and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports firmware level | |--------------+---------------------------------------------| | I5 | Reports country code | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S24=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating low-power sleep | | | mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Fn [cmds] | |--------------+---------------------------------------------| | Description: | Displays phone number directory | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S16=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-125 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls loopback tests, analog, digital, | | | remote digital, and self tests. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Local analog loopback not in progress | | | | | | | 1 | Local analog loopback in progress | |------+-------+---------------------------------------------| | 1 | 0 | Not used | |------+-------+---------------------------------------------| | 2 | 0 | Local digital loopback not in progress | | | | | | | 1 | Local digital loopback in progress | |------+-------+---------------------------------------------| | 3 | 0 | Modem not in remote digital loopback | | | | | | | 1 | Remote digital loopback in progress | |------+-------+---------------------------------------------| | 4 | 0 | Remote digital loopback not requested | | | | | | | 1 | Remote digital loopback requested | |------+-------+---------------------------------------------| | 5 | 0 | Remote digital loopback w/ self-test not in | | | | progress | | | 1 | | | | | Remote digital loopback w/ self-test in | | | | progress | |------+-------+---------------------------------------------| | 6 | 0 | Local analog loopback w/ self-test not in | | | | progress | | | 1 | | | | | Local analog loopback w/ self-test in | | | | progress | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - CELLULAR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @Mn [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-31 | |--------------+---------------------------------------------| | Unit: | -1dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in cellular mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - FAX | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S92=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission | | | while in fax mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL - PSTN | |------------------------------------------------------------| | Type | Register | |-------------+----------------------------------------------| | Format | AT [cmds] S91=n [cmds] | |-------------+----------------------------------------------| | Default | Unidentified | |-------------+----------------------------------------------| | Range | 0-15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal level for transmission over | | | switched phone lines | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.32 - COMPROMISE EQUALIZER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] :En [cmds] | |--------------+---------------------------------------------| | Description: | Controls V.32 compromise equalizer | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | :E0 | Equalizer disabled | |--------------+---------------------------------------------| | i :E1 | Equalizer enabled |