MOTOROLA, INC. ============== HMTA 200 V.34 Card Type ISDN TA Chip Set Motorola ISDN Transfer Rate 64Kbps x 2 Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Fax Class Unidentified Data Bus External ISDN Protocol V.120, PPP, AIMux, Bonding Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Unidentified Protocol Switch Type 5ESS, DMS-100, NI-1 Error MNP5, V.42bis Correction/Compression Proprietary AT Command Set V2153 +------------------------------------------------------------+ | AUTO-RELIABLE BUFFER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the behaviour of the buffer during | | | auro-reliable negotiation. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i \C0 | Auto-reliable buffer disabled. | |---------------+--------------------------------------------| | \C1 | Modem will buffer data for four seconds or | | | 200 bytes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BEARER CALL - 3.1KHz AUDIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A94=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects how the TA will answer an incoming | | | 3.1KHz audio BC call. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | %A94=D | TA will not answer 3.1KHz audio BC calls. | |---------------+--------------------------------------------| | %A94=E | TA will answer 3.1KHz audio BC calls as | | | ISDN. | |---------------+--------------------------------------------| | i %A94=M | TA will answer 3.1KHz audio BC calls with | | | the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BEARER CALL - DATA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A95=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects how the TA will answer an incoming | | | data BC call. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | %A93=D | TA will not answer data BC calls. | |-----------------+------------------------------------------| | i %A93=E | TA will answer data BC calls as ISDN. | |-----------------+------------------------------------------| | %A93=M | TA will answer data BC calls with the | | | modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BEARER CALL - SPEECH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A93=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects how the TA will answer an incoming | | | speech BC call. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | %A93=D | TA will not answer speech BC calls. | |----------------+-------------------------------------------| | %A93=E | TA will answer speech BC calls as ISDN. | |----------------+-------------------------------------------| | i %A93=M | TA will answer speech BC calls with the | | | modem. | +------------------------------------------------------------+ +----------------------------------------------------------------+ | BREAK TYPE | |----------------------------------------------------------------| |Type: |Configuration | |------------------+---------------------------------------------| |Format: |AT [cmds] \Kn [cmds] | |------------------+---------------------------------------------| |Description: |Configures action of break signal. | |----------------------------------------------------------------| | Command |Break from DTE | Break from | Modem | Break from | | | | DTE |receives \B |remote modem| | |Reliable/Normal| | | | | | mode |Direct mode | | | |---------+---------------+------------+------------+------------| | \K1 |Buffers cleared|Send break |Buffers |Buffers | | |and break sent |to remote |cleared and |cleared and | | |to remote |modem |break sent |break sent | | |modem. |immediately.|to remote |to DTE. | | | | |modem. | | |---------+---------------+------------+------------+------------| | \K3 |Send break to |Send break |Send break |Send break | | |remote modem |to remote |to remote |to DTE | | |immediately. |modem |modem |immediately.| | | |immediately.|immediately.| | |---------+---------------+------------+------------+------------| | i \K5 |Send break with|Send break |Send break |Break sent | | |transmitted |to remote |to remote |with | | |data. |modem |modem with |received | | | |immediately.|transmitted |data to the | | | | |data. |DTE. | +----------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @N0=n [cmds] | |--------------+---------------------------------------------| | Description: | Enables the Caller ID function. | |------------------------------------------------------------| | Command | Function | |----------------------+-------------------------------------| | i @N0=0 | Caller ID disabled. | |----------------------+-------------------------------------| | @N0=1 | Caller ID enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLER ID LOG | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] @Ln [cmds] | |--------------+---------------------------------------------| | Description: | Allows the user to view and clear the | | | Caller ID log. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | @L0 | Clears the Caller ID log. | |---------------+--------------------------------------------| | @L1 | View the last entry in the Caller ID log. | |---------------+--------------------------------------------| | @L2 | View the last ten entries in the Caller ID | | | log. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CD SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CD signal. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | i &C0 | CD forced high. | |---------------------+--------------------------------------| | &C1 | CD normal. | |---------------------+--------------------------------------| | &C2 | CD forced low on disconnect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMAND SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @P1=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects the command set that will be used. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | @P1=A | AT command set enabled. | |----------------+-------------------------------------------| | @P1=N | Command sets disabled. | |----------------+-------------------------------------------| | @P1=VB | V.25bis command set enabled in Bisync | | | mode. | |----------------+-------------------------------------------| | @P1=VH | V.25bis command set enabled in HDLC mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects how the modem will compress data. | |------------------------------------------------------------| | Command | Function | |-------------------------+----------------------------------| | %C0 | Compression disabled. | |-------------------------+----------------------------------| | %C1 | Compression enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION/ERROR CORRECTION MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the types of compression and error | | | correction that will be attempted. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | \N0 | Normal mode only, compression and error | | | correction disabled. | |---------------+--------------------------------------------| | \N1 | Direct mode only, compression and error | | | correction disabled. | |---------------+--------------------------------------------| | \N2 | MNP attempted, modem will disconnect if | | | MNP connection fails. | |---------------+--------------------------------------------| | \N3 | MNP attempted, modem will attempt normal | | | mode if MNP connection fails. | |---------------+--------------------------------------------| | \N4 | LAPM attempted, modem will disconnect if | | | LAPM connection fails. | |---------------+--------------------------------------------| | \N5 | LAPM attempted, modem will attempt normal | | | mode if LAPM connection fails. | |---------------+--------------------------------------------| | \N6 | LAPM attempted, then MNP, modem will | | | disconnect if both previous connections | | | fail. | |---------------+--------------------------------------------| | \N7 | LAPM attempted, then MNP, modem will | | | attempt normal mode if both previous | | | connections fail. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA LENGTH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @P4=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the length of the data word. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | @P4=7 | 7 bit word length. | |------------------------+-----------------------------------| | i @P4=8 | 8 bit word length. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA PARITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @P3=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects the format of the parity bit. | |------------------------------------------------------------| | Command | Function | |----------------------------+-------------------------------| | @P3=E | Even parity. | |----------------------------+-------------------------------| | @P3=M | Mark parity. | |----------------------------+-------------------------------| | i @P3=N | No parity. | |----------------------------+-------------------------------| | @P3=O | Odd parity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA STOP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @P6=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the number of stop bits. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | i @P6=0 | One stop bit. | |-------------------+----------------------------------------| | @P6=1 | One and a half stop bits. | |-------------------+----------------------------------------| | @P6=2 | Two stop bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A97=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects what type of dialing the TA will | | | use. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | i %A97=E | En bloc dialing enabled. | |------------------------+-----------------------------------| | %A97=O | Overlap dialing enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIRECTORY NUMBER 1 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT !N1=<#> | | | | | | AT [cmds] !N1="<#>" [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first directory number. The number | | | must be surrounded by single or double | | | quotes if there are more commands on the | | | line. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIRECTORY NUMBER 2 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT !N2=<#> | | | | | | AT [cmds] !N2="<#>" [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first directory number. The number | | | must be surrounded by single or double | | | quotes if there are more commands on the | | | line. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT BUFFER TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the time that the modem will wait to | | | disconnect if there is data in its buffers. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] >V=x [cmds] | |--------------+---------------------------------------------| | Description: | Displays information about the current | | | configuration. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | >V=C | Displays directory numbers, SPIDs, and | | | TEIs. | |---------------+--------------------------------------------| | >V=G | Displays complete configuration. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CONFIGURATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V=x[n] [cmds] | |--------------+---------------------------------------------| | Description: | Displays information about the current | | | configuration. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V | Displays current and stored profiles. | |--------------+---------------------------------------------| | &V=Bn | Displays X.25 session n. | |--------------+---------------------------------------------| | &V=E | Displays V.120 CSD information. | |--------------+---------------------------------------------| | &V=Ln | Displays local X.25 session n. | |--------------+---------------------------------------------| | &V=Rn | Displays remote X.25 session n. | |--------------+---------------------------------------------| | &V=Z | Displays stored phone numbers. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY FIRMWARE VERSION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays the version of the installed | | | firmware. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY PRODUCT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information about the TA. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification. | |--------------+---------------------------------------------| | I1 | Displays ROM checksum. | |--------------+---------------------------------------------| | I2 | Displays ROM checksum response. | |--------------+---------------------------------------------| | I3 | Displays firmware version. | |--------------+---------------------------------------------| | I4 | Displays modem capability in numeric form. | |--------------+---------------------------------------------| | I8 | Displays modem capability in verbose form. | |--------------+---------------------------------------------| | I9 | Displays Plug-And-Play ID. | |--------------+---------------------------------------------| | I10 | Displays ISDN link status. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR AUTODIAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Causes the TA to repeatedly dial the first | | | stored number on high DTR until it | | | connects. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i &L0 | DTR autodialing disabled. | |-----------------------+------------------------------------| | &L1 | DTR autodialing enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR CHANGE TIME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S25=n [cmds] | |--------------+---------------------------------------------| | Default: | 5 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 10ms | |--------------+---------------------------------------------| | Description: | Sets the amount of time the DTR signal must | | | be low before it is recognized. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DTR signal. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | &D0 | DTR forced high. | |---------------+--------------------------------------------| | &D1 | TA enters command mode when DTR goes low. | |---------------+--------------------------------------------| | &D2 | TA hangs up and returns to command mode on | | | low DTR. | |---------------+--------------------------------------------| | &D3 | TA resets on low DTR. | |---------------+--------------------------------------------| | &D9 | TA dials first stored number on high DTR, | | | hangs up and returns to command mode on | | | low DTR. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ECHO CANCELLER DISABLE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A96=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the TA will send a tone to | | | disable the echo canceller. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i %A96=0 | TA will not send echo canceller disable | | | tone. | |---------------+--------------------------------------------| | %A96=1 | TA will send echo canceller disable tone. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES - MODEM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects which speed the modem will display | | | for connect messages. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | \V0 | Display serial port speed only. | |----------------+-------------------------------------------| | \V1 | Display serial port speed and error | | | correction protocol. | |----------------+-------------------------------------------| | \V2 | Display line speed only. | |----------------+-------------------------------------------| | \V3 | Display line speed and error correction | | | protocol. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES - ISDN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Wn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the TA will send extended | | | protocol and channel result codes. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | i W0 | Extended result codes disabled. | |-------------------+----------------------------------------| | W1 | Extended result codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL - MODEM-TO-MODEM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the local and remote modems | | | may use flow control. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | i \G0 | Modem-to-modem XON/XOFF flow control | | | disabled. | |------------------+-----------------------------------------| | \G1 | Modem-to-modem XON/XOFF flow control | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the type of flow control that will | | | be used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | \Q0 | Flow control disabled. | |------------------+-----------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control | | | enabled. | |------------------+-----------------------------------------| | \Q2 | CTS flow control enabled. | |------------------+-----------------------------------------| | i \Q3 | RTS/CTS flow control enabled. | |------------------+-----------------------------------------| | \Q4 | Unidirectional XON/XOFF flow control | | | enabled. | |------------------------------------------------------------| | Note: Unidirectional XON/XOFF is valid for ISDN | | operation only. If this mode is used while operating | | the modem it will not function properly. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FRONT PANEL LOCK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] >Ln [cmds] | |--------------+---------------------------------------------| | Description: | Prevents front panel configuration changes. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i >L0 | All actions allowed from front panel. | |---------------+--------------------------------------------| | >L1 | Configuration changes from front panel not | | | allowed. | |---------------+--------------------------------------------| | >L2 | No actions allowed from front panel. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the amount of time that the modem must | | | be idle before it will disconnect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED - MAXIMUM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum speed the modem will | | | connect at. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | %B0 | Modem will connect only at DCE speed. | |---------------+--------------------------------------------| | %B300 | Modem will connect only at 300bps. | |---------------+--------------------------------------------| | %B600 | 600bps maximum connect speed. | |---------------+--------------------------------------------| | %B1200 | 1200bps maximum connect speed. | |---------------+--------------------------------------------| | %B2400 | 2400bps maximum connect speed. | |---------------+--------------------------------------------| | %B4800 | 4800bps maximum connect speed. | |---------------+--------------------------------------------| | %B7200 | 7200bps maximum connect speed. | |---------------+--------------------------------------------| | %B9600 | 9600bps maximum connect speed. | |---------------+--------------------------------------------| | %B9600C | 9600bps maximum connect speed with trellis | | | coding. | |---------------+--------------------------------------------| | %B12000 | 12Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B14400 | 14.4Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B16800 | 16.8Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B19200 | 19.2Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B21600 | 21.6Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B24000 | 24Kbps maximum connect speed. | |---------------+--------------------------------------------| | %B26400 | 26.4Kbps maximum connect speed. | |---------------+--------------------------------------------| | i %B28800 | Modem will connect at any speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SPEED - MINIMUM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Ln [cmds] | |--------------+---------------------------------------------| | Description: | Sets the minimum speed the modem will | | | connect at. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i %L300 | Modem will connect at any speed. | |---------------+--------------------------------------------| | %L1200 | 1200bps minimum connect speed. | |---------------+--------------------------------------------| | %L2400 | 2400bps minimum connect speed. | |---------------+--------------------------------------------| | %L4800 | 4800bps minimum connect speed. | |---------------+--------------------------------------------| | %L7200 | 7200bps minimum connect speed. | |---------------+--------------------------------------------| | %L9600 | 9600bps minimum connect speed. | |---------------+--------------------------------------------| | %L9600C | 9600bps minimum connect speed with trellis | | | coding. | |---------------+--------------------------------------------| | %L12000 | 12Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L14400 | 14.4Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L16800 | 16.8Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L19200 | 19.2Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L21600 | 21.6Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L24000 | 24Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L26400 | 26.4Kbps minimum connect speed. | |---------------+--------------------------------------------| | %L28800 | Modem will connect only at 28.8Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOAD STORED PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Zn [cmds] | |--------------+---------------------------------------------| | Description: | Loads the configuration of the TA from the | | | stored profile except for ISDN settings. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOAD STORED PROFILE - FULL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] >Zn [cmds] | |--------------+---------------------------------------------| | Description: | Loads the complete configuration of the TA | | | from the stored profile. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @P2=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of operation for the serial | | | port. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | @P2=300 | Set serial port speed to 300bps. | |------------------+-----------------------------------------| | @P2=600 | Set serial port speed to 600bps. | |------------------+-----------------------------------------| | @P2=1200 | Set serial port speed to 1200bps. | |------------------+-----------------------------------------| | @P2=2400 | Set serial port speed to 2400bps. | |------------------+-----------------------------------------| | @P2=4800 | Set serial port speed to 4800bps. | |------------------+-----------------------------------------| | @P2=7200 | Set serial port speed to 7200bps. | |------------------+-----------------------------------------| | @P2=9600 | Set serial port speed to 9600bps. | |------------------+-----------------------------------------| | @P2=12000 | Set serial port speed to 12Kbps. | |------------------+-----------------------------------------| | @P2=14400 | Set serial port speed to 14.4Kbps. | |------------------+-----------------------------------------| | @P2=19200 | Set serial port speed to 19.2Kbps. | |------------------+-----------------------------------------| | @P2=28800 | Set serial port speed to 28.8Kbps. | |------------------+-----------------------------------------| | @P2=38400 | Set serial port speed to 38.4Kbps. | |------------------+-----------------------------------------| | @P2=48000 | Set serial port speed to 48Kbps. | |------------------+-----------------------------------------| | @P2=56000 | Set serial port speed to 56Kbps. | |------------------+-----------------------------------------| | i @P2=57600 | Set serial port speed to 57.6Kbps. | |------------------+-----------------------------------------| | @P2=64000 | Set serial port speed to 64Kbps. | |------------------+-----------------------------------------| | @P2=112000 | Set serial port speed to 112Kbps. | |------------------+-----------------------------------------| | @P2=115200 | Set serial port speed to 115.2Kbps. | |------------------+-----------------------------------------| | @P2=128000 | Set serial port speed to 128Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the serial port speed will | | | be matched to the line speed. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i \J0 | Serial port speed locked. | |---------------+--------------------------------------------| | \J1 | Serial port speed will match line speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP BLOCK SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum size of a block in MNP | | | mode. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | \A0 | Maximum block size is 64 bytes. | |--------------------+---------------------------------------| | \A1 | Maximum block size is 128 bytes. | |--------------------+---------------------------------------| | \A2 | Maximum block size is 192 bytes. | |--------------------+---------------------------------------| | \A3 | Maximum block size is 256 bytes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ORIGINATE CALL - ISDN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A98=Ix [cmds] | |--------------+---------------------------------------------| | Description: | Selects what bearer capability the TA will | | | originate ISDN calls with. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | %A98=I | Originate ISDN calls as data BC. | |---------------+--------------------------------------------| | %A98=IA | Originate ISDN calls as 3.1KHz audio BC. | |---------------+--------------------------------------------| | i %A98=ID | Originate ISDN calls as data BC. | |---------------+--------------------------------------------| | %A98=IS | Originate ISDN calls as speech BC. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ORIGINATE CALL - MODEM | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A98=Mx [cmds] | |--------------+---------------------------------------------| | Description: | Selects what bearer capability the TA will | | | originate modem calls with. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | %A98=M | Originate modem calls as 3.1KHz audio BC. | |---------------+--------------------------------------------| | i %A98=MA | Originate modem calls as 3.1KHz audio BC. | |---------------+--------------------------------------------| | %A98=MD | Originate modem calls as data BC. | |---------------+--------------------------------------------| | %A98=MS | Originate modem calls as speech BC. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A2=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the protocol that the TA uses for rate | | | adaptation. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | %A2=0 | TA will use clear channel mode. | |-------------------+----------------------------------------| | i %A2=2 | TA will use V.120 protocol. | |-------------------+----------------------------------------| | %A2=3 | TA will use Bonding Mode 1 or AIMux | | | protocols. | |-------------------+----------------------------------------| | %A2=95 | TA will use PPP protocol. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TO FACTORY DEFAULTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Resets the configuration of the TA except | | | for ISDN settings to the factory defaults. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TO FACTORY DEFAULT - FULL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] >F [cmds] | |--------------+---------------------------------------------| | Description: | Resets the complete configuration of the TA | | | to the factory defaults. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RETRAIN | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] On | |--------------+---------------------------------------------| | Description: | When connected, tells the modem to go back | | | online and initiate a retrain. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | Return online without retrain. | |---------------+--------------------------------------------| | O1 | Return online with retrain. | |---------------+--------------------------------------------| | O14400 | Return online and negotiate to 14.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RETRAIN | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #Rn [cmds] | |--------------+---------------------------------------------| | Description: | Forces the modem to attempt to retrain to | | | the selected speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #R0 | Attempt 2400bps speed. | |--------------+---------------------------------------------| | #R1 | Attempt 4800bps speed. | |--------------+---------------------------------------------| | #R2 | Attempt 7200bps speed. | |--------------+---------------------------------------------| | #R3 | Attempt 9600bps speed. | |--------------+---------------------------------------------| | #R4 | Attempt 12Kbps speed. | |--------------+---------------------------------------------| | #R5 | Attempt 14.4Kbps speed. | |--------------+---------------------------------------------| | #R6 | Attempt 16.8Kbps speed. | |--------------+---------------------------------------------| | #R7 | Attempt 19.2Kbps speed. | |--------------+---------------------------------------------| | #R8 | Attempt 21.6Kbps speed. | |--------------+---------------------------------------------| | #R9 | Attempt 24Kbps speed. | |--------------+---------------------------------------------| | #R10 | Attempt 26.4Kbps speed. | |--------------+---------------------------------------------| | #R11 | Attempt 28.8Kbps speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RETRAIN SENSITIVITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Rn [cmds] | |--------------+---------------------------------------------| | Description: | Sets how poor line conditions must be | | | before the modem will initiate a retrain. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %R0 | Modem will not initiate retrain. | |--------------+---------------------------------------------| | %R1 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-5 for eight seconds. | |--------------+---------------------------------------------| | %R2 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-4 for eight seconds. | |--------------+---------------------------------------------| | %R3 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-3 for eight seconds. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPID 1 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT !C6=<#> | | | | | | AT [cmds] !C6="<#>" [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first SPID. The SPID must be | | | surrounded by single or double quotes if | | | there are more commands on the line. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPID 2 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT !C7=<#> | | | | | | AT [cmds] !C7="<#>" [cmds] | |--------------+---------------------------------------------| | Description: | Sets the second SPID. The SPID must be | | | surrounded by single or double quotes if | | | there are more commands on the line. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCH TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !C0=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects what type of network switch the TA | | | is connected to. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | !C0=0 | TA is connected to 5ESS switch. | |------------------+-----------------------------------------| | !C0=1 | TA is connected to DMS-100 switch. | |------------------+-----------------------------------------| | i !C0=2 | TA is connected to NI-1 switch. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCH VERSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !C1=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects what version of network switch the | | | TA is connected to. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | !C1=0 | TA is connected to point-to-point 5ESS | | | switch. | |---------------+--------------------------------------------| | !C1=1 | TA is connected to multipoint 5ESS switch. | |---------------+--------------------------------------------| | !C1=2 | TA is connected to IC-0 DMS-100 switch. | |---------------+--------------------------------------------| | !C1=3 | TA is connected to IC-1 DMS-100 switch. | |---------------+--------------------------------------------| | i !C1=4 | TA is connected to NI-1 switch. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SYNC/ASYNC MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the DTE will be operation | | | in synchronous or asynchronous mode. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i &M0 | DTE in asynchronous mode. | |---------------+--------------------------------------------| | &M1 | DTE in asynchronous mode for dialing, | | | synchronous mode for communications. | |---------------+--------------------------------------------| | &M2 | DTE in synchronous mode, TA dials stored | | | number on high DTR. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEI 1 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !D3=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the first Terminal Endpoint | | | Identifier. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | !D3=0 | Sets the TEI to the value indicated. | | | | | ... | | | | | | !D3=63 | | |------------------+-----------------------------------------| | !D3=127 | Disables channel 1. | |------------------+-----------------------------------------| | i !D3=255 | Allows dynamic TEI assignment. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEI 2 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !D4=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the second Terminal Endpoint | | | Identifier. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | !D4=0 | Sets the TEI to the value indicated. | | | | | ... | | | | | | !D4=63 | | |------------------+-----------------------------------------| | i !D4=127 | Disables channel 2. | |------------------+-----------------------------------------| | !D4=255 | Allows dynamic TEI assignment. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEI X.25 SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !D0=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the Terminal Endpoint Identifier for | | | X.25. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | !D0=0 | Sets the TEI to the value indicated. | | | | | ... | | | | | | !D0=63 | | |-----------------+------------------------------------------| | i !D0=127 | Disables X.25 operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #Tn [cmds] | |--------------+---------------------------------------------| | Default: | 9 | |--------------+---------------------------------------------| | Range: | 9 - 30 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission for | | | the modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %A4=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the transmission speed of the TA. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | %A4=0 | Transmission speed is 64Kbps. | |-------------------+----------------------------------------| | %A4=1 | Transmission speed is 56Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.34 ASYMMETRIC MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #An [cmds] | |--------------+---------------------------------------------| | Description: | Allows the modem to transmit and receive at | | | different rates. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #A0 | V.34 split baud mode disabled. | |--------------+---------------------------------------------| | #A1 | V.34 split baud mode enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.34 FAST TRAIN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the normal or fast training | | | sequence for V.34. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #F0 | Normal handshaking enabled. | |--------------+---------------------------------------------| | i #F1 | Fast handshaking enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.34 RETRAIN SENSITIVITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #Hn [cmds] | |--------------+---------------------------------------------| | Description: | Sets how poor line conditions must be | | | before the modem will initiate a retrain | | | when in V.34 mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #H0 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-6. | |--------------+---------------------------------------------| | #H1 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-4. | |--------------+---------------------------------------------| | #H2 | Modem will initiate retrain when the Bit | | | Error Rate exceeds 10-2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42 FAST DETECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the normal or fast detection | | | sequence for V.42. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \M0 | Normal handshaking enabled. | |--------------+---------------------------------------------| | i \M1 | Fast handshaking enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.120 RECEIVE FRAME SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %E1=n [cmds] | |--------------+---------------------------------------------| | Default: | 256 | |--------------+---------------------------------------------| | Range: | 1 - 260 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Sets the maximum size of a received V.120 | | | frame. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.120 TRANSMIT FRAME SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %E0=n [cmds] | |--------------+---------------------------------------------| | Default: | 256 | |--------------+---------------------------------------------| | Range: | 1 - 260 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Sets the maximum size of a transmitted | | | V.120 frame. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.120 TRANSMIT TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %E3=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 1 - 255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the V.120 T200 transmission timer. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.120 WINDOW SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %E2=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 1 - 127 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the V.120 window. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42 FAST DETECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the normal or fast negotiation | | | sequence for V.42. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | \M0 | V.42 fast detect disabled. | |--------------------+---------------------------------------| | i \M1 | V.42 fast detect enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | WRITE PROTECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] @G=x [cmds] | |--------------+---------------------------------------------| | Description: | Selects the ability to prevent permanent | | | changes to the TA's configuration from | | | being made. All changes made in temporary | | | memory will be reset at the end of every | | | call. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i @G=D | Write protect disabled. | |-----------------------+------------------------------------| | @G=E | Write protect enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | WRITE TO STORED PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Wn [cmds] | |--------------+---------------------------------------------| | Description: | Saves the configuration of the TA except | | | for ISDN settings to stored profile n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | WRITE TO STORED PROFILE - FULL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] >Wn [cmds] | |--------------+---------------------------------------------| | Description: | Saves the complete configuration of the TA | | | to stored profile n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 AUTO-ANSWER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B97=x [cmds] | |--------------+---------------------------------------------| | Description: | Sets whether the TA will auto-answer an | | | incoming X.25 virtual call. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | %B97=D | Auto-answer disabled. | |------------------------+-----------------------------------| | i %B97=E | Auto-answer enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 CALL CHARGING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B10=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the type of call charging for X.25. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | i %B10=0 | X.25 will use normal call charging. | |-----------------+------------------------------------------| | %B10=1 | X.25 will use reverse call charging. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 CLOSED USER GROUP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B8=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the type of Closed User Group used | | | for X.25. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | i %B8=0 | CUG not used. | |------------------+-----------------------------------------| | %B8=1 | Basic CUG used. | |------------------+-----------------------------------------| | %B8=2 | CUG with outgoing access only used. | |------------------+-----------------------------------------| | %B8=3 | CUG will full access used. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 CLOSED USER GROUP ID | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B9=nnnn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the ID for the X.25 CUG. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 CODE - INCOMING | |------------------------------------------------------------| | Type: | Read-only | |--------------+---------------------------------------------| | Format: | AT [cmds] %B16? [cmds] | |--------------+---------------------------------------------| | Description: | Stores the result code for incoming X.25 | | | virtual calls. | |------------------------------------------------------------| | Value | Meaning | |----------------------+-------------------------------------| | 0 | Call was not redirected. | |----------------------+-------------------------------------| | 1 | Station was busy. | |----------------------+-------------------------------------| | 9 | Station was out of order. | |----------------------+-------------------------------------| | 15 | Call was redirected. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 CODE - OUTGOING | |------------------------------------------------------------| | Type: | Read-only | |--------------+---------------------------------------------| | Format: | AT [cmds] %B15? [cmds] | |--------------+---------------------------------------------| | Description: | Stores the result code for outgoing X.25 | | | virtual calls. | |------------------------------------------------------------| | Value | Meaning | |--------------------+---------------------------------------| | 0 | Call was not redirected. | |--------------------+---------------------------------------| | 1 | Station was busy. | |--------------------+---------------------------------------| | 7 | Call was within a hunt group. | |--------------------+---------------------------------------| | 9 | Station was out of order. | |--------------------+---------------------------------------| | 15 | Call was redirected. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !C3=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether X.25 will be used on the | | | D-channel. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | i !C3=0 | X.25 disabled on D-channel. | |---------------------+--------------------------------------| | !C3=1 | X.25 enabled on D-channel. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - CHANNELS, BIDIRECTIONAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X6=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the number of bidirectional logical | | | channels for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - CHANNELS, INCOMING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X5=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the number of incoming logical | | | channels for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - CHANNELS, OUTGOING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X7=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the number of outgoiing logical | | | channels for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - CHANNELS, VIRTUAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X4=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the number of permanent virtual | | | channels for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - MODULUS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X8=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 8, 128 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the sequence modulus for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !D1=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects X.25 parameter negotiation. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | !D1=0 | X.25 negotiation disabled. | |--------------------+---------------------------------------| | i !D1=1 | X.25 negotiation enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - RECEIVE PACKET SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X2=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the size of the received packets for | | | X.25. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | i !X2=7 | Packet size set to 128 bytes. | |--------------------+---------------------------------------| | !X2=8 | Packet size set to 256 bytes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - RECEIVE WINDOW SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X0=n [cmds] | |--------------+---------------------------------------------| | Default: | 2 | |--------------+---------------------------------------------| | Range: | 1 - 7 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the X.25 receive window. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - TRANSMIT PACKET SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X3=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the size of the transmitted packets | | | for X.25. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | i !X3=7 | Packet size set to 128 bytes. | |--------------------+---------------------------------------| | !X3=8 | Packet size set to 256 bytes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 D-CHANNEL - TRANSMIT WINDOW SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] !X1=n [cmds] | |--------------+---------------------------------------------| | Default: | 2 | |--------------+---------------------------------------------| | Range: | 1 - 7 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the X.25 transmit window. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 LOGICAL CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B6=n [cmds] | |--------------+---------------------------------------------| | Default: | 1 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Selects the logical channel for X.25 | | | operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 OUTGOING CALL ADDRESS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B17=nnnn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the address for an outgoing X.25 | | | virtual call. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PACKET CALL TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B98=n [cmds] | |--------------+---------------------------------------------| | Default: | 200 | |--------------+---------------------------------------------| | Range: | 0 - 600 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the packet call timer for X.25 | | | operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD ANCILLARY DEVICE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L5=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects control of an ancillary device by | | | the PAD. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | %L5=0 | Device disabled. | |----------------+-------------------------------------------| | i %L5=1 | Device enabled for data transfer only. | |----------------+-------------------------------------------| | %L5=2 | Device enabled for data transfer and | | | command control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD BREAK RESPONSE | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] %L7=n [cmds] | |----------------+-------------------------------------------| | Default: | 0 | |----------------+-------------------------------------------| | Range: | 0 - 31 | |----------------+-------------------------------------------| | Description: | Sets action the PAD takes in response to | | | receiving a BREAK from the DTE. | |------------------------------------------------------------| | Bit | Value | Function | |----------+--------+----------------------------------------| | 0 | i 0 | PAD will not send an interrupt packet. | | | | | | | 1 | PAD will send an interrupt packet. | |----------+--------+----------------------------------------| | 1 | i 0 | PAD will not send a reset packet. | | | | | | | 1 | PAD will send a reset packet. | |----------+--------+----------------------------------------| | 2 | i 0 | PAD will not send an indication of the | | | | break. | | | 1 | | | | | PAD will send an indication of the | | | | break. | |----------+--------+----------------------------------------| | 3 | i 0 | PAD will not escape from the data | | | | state. | | | 1 | | | | | PAD will escape from the data state. | |----------+--------+----------------------------------------| | 4 | i 0 | PAD will not set %L8 to 1. | | | | | | | 1 | PAD will set %L8 to 1. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD CARRIAGE RETURN TRANSLATION | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] %L13=n [cmds] | |----------------+-------------------------------------------| | Default: | 5 | |----------------+-------------------------------------------| | Range: | 0 - 7 | |----------------+-------------------------------------------| | Description: | Selects when the PAD will add line feeds | | | to carriage returns. | |------------------------------------------------------------| | Bit | Value | Function | |----------+--------+----------------------------------------| | 0 | 0 | PAD will not add a line feed after a | | | | carriage return being sent to the DTE. | | | i 1 | | | | | PAD will add a line feed after a | | | | carriage return being sent to the DTE. | |----------+--------+----------------------------------------| | 1 | i 0 | PAD will not add a line feed after a | | | | carriage return being received from | | | 1 | the DTE. | | | | | | | | PAD will add a line feed after a | | | | carriage return being received from | | | | the DTE. | |----------+--------+----------------------------------------| | 2 | 0 | PAD will not add a line feed after a | | | | carriage return being echoed. | | | i 1 | | | | | PAD will add a line feed after a | | | | carriage return being echoed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - CARRIAGE RETURN PADDING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L9=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the amount of padding after a carriage | | | return. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD DATA EDITING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L15=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether editing the data being | | | transferred is allowed. | |------------------------------------------------------------| | Command | Function | |-------------------------+----------------------------------| | %L12=0 | Editing disabled. | |-------------------------+----------------------------------| | i %L12=1 | Editing enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD DELETE CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L16=n [cmds] | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used for character | | | deletion. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - DISCARD DATA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L8=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the PAD will deliver data | | | to the DTE. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i %L8=0 | Deliver data to the DTE. | |-----------------------+------------------------------------| | %L8=1 | Discard data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD ECHO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L2=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether PAD functions will echo | | | incoming characters. | |------------------------------------------------------------| | Command | Function | |-------------------------+----------------------------------| | %L2=0 | PAD echo disabled. | |-------------------------+----------------------------------| | i %L2=1 | PAD echo enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD ECHO MASK | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] %L20=n [cmds] | |----------------+-------------------------------------------| | Default: | 248 | |----------------+-------------------------------------------| | Range: | 0 - 255 | |----------------+-------------------------------------------| | Description: | Selects which control characters will be | | | echoed. | |------------------------------------------------------------| | Bit | Value | Function | |----------+--------+----------------------------------------| | 0 | i 0 | Carriage return will be echoed. | | | | | | | 1 | Carriage return will not be echoed. | |----------+--------+----------------------------------------| | 1 | i 0 | Line feed will be echoed. | | | | | | | 1 | Line feed will not be echoed. | |----------+--------+----------------------------------------| | 2 | i 0 | The control characters VT, HT, and | | | | form feeds will be echoed. | | | 1 | | | | | The control characters VT, HT, and | | | | form feeds will not be echoed. | |----------+--------+----------------------------------------| | 3 | 0 | Bells and backspaces will be echoed. | | | | | | | i 1 | Bells and backspaces will not be | | | | echoed. | |----------+--------+----------------------------------------| | 4 | 0 | The control character ENQ and escapes | | | | will be echoed. | | | i 1 | | | | | The control character ENQ and escapes | | | | will not be echoed. | |----------+--------+----------------------------------------| | 5 | 0 | The control characters ACK, NAK, STX, | | | | SOH, EOT, ETB, and ETX will be echoed. | | | i 1 | | | | | The control characters ACK, NAK, STX, | | | | SOH, EOT, ETB, and ETX will not be | | | | echoed. | |----------+--------+----------------------------------------| | 6 | 0 | Parameters 16, 17, and 18 will be | | | | echoed. | | | i 1 | | | | | Parameters 16, 17, and 18 will not be | | | | echoed. | |----------+--------+----------------------------------------| | 7 | 0 | All other control characters will be | | | | echoed. | | | i 1 | | | | | All other control characters will not | | | | be echoed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L12=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects flow control for the X.25 PAD. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | %L12=0 | Flow control disabled. | |-----------------------+------------------------------------| | i %L12=1 | Flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - FORM FEED PADDING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L22=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the amount of padding after a form | | | feed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD FORWARDING | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] %L3=n [cmds] | |----------------+-------------------------------------------| | Default: | 2 | |----------------+-------------------------------------------| | Range: | 0 - 127 | |----------------+-------------------------------------------| | Description: | Selects which characters will be | | | forwarded through the PAD. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | i 0 | Alphanumeric characters will not be | | | | forwarded. | | | 1 | | | | | Alphanumeric characters (A-Z, a-z, 0-9) | | | | will be forwarded. | |----------+-------+-----------------------------------------| | 1 | 0 | Carriage returns will not be forwarded. | | | | | | | i 1 | Carriage returns will be forwarded. | |----------+-------+-----------------------------------------| | 2 | i 0 | The control characters ENQ, ACK, bells, | | | | and escapes will not be forwarded. | | | 1 | | | | | The control characters ENQ, ACK, bells, | | | | and escapes will be forwarded. | |----------+-------+-----------------------------------------| | 3 | i 0 | The control characters CAN, DC2, and | | | | delete will not be forwarded. | | | 1 | | | | | The control characters CAN, DC2, and | | | | delete will be forwarded. | |----------+-------+-----------------------------------------| | 4 | i 0 | The control characters ETX and EOT will | | | | not be forwarded. | | | 1 | | | | | The control characters ETX and EOT will | | | | be forwarded. | |----------+-------+-----------------------------------------| | 5 | i 0 | The control characters HT, LT, VT, and | | | | form feeds will not be forwarded. | | | 1 | | | | | The control characters HT, LT, VT, and | | | | FF will be forwarded. | |----------+-------+-----------------------------------------| | 6 | i 0 | All other control characters will not | | | | be forwarded. | | | 1 | | | | | All other control characters will be | | | | forwarded. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD IDLE TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L4=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the PAD's idle time delay. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD LINE DELETE CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L17=n [cmds] | |--------------+---------------------------------------------| | Default: | 24 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used for line deletion. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD LINE DISPLAY CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L18=n [cmds] | |--------------+---------------------------------------------| | Default: | 18 | |--------------+---------------------------------------------| | Range: | 0 - 127 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character | |--------------+---------------------------------------------| | Description: | Sets the character used for line display. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - LINE FEED PADDING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L14=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the amount of padding after a line | | | feed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - LINE WRAP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L10=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 character | |--------------+---------------------------------------------| | Description: | Sets the length of a line for the X.25 PAD. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD - LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L11=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the speed of operation for the serial | | | port when using the X.25 PAD. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | %L11=2 | Set serial port speed to 300bps. | |------------------+-----------------------------------------| | %L11=3 | Set serial port speed to 1200bps. | |------------------+-----------------------------------------| | %L11=4 | Set serial port speed to 600bps. | |------------------+-----------------------------------------| | %L11=12 | Set serial port speed to 2400bps. | |------------------+-----------------------------------------| | %L11=13 | Set serial port speed to 4800bps. | |------------------+-----------------------------------------| | %L11=14 | Set serial port speed to 9600bps. | |------------------+-----------------------------------------| | %L11=15 | Set serial port speed to 19.2Kbps. | |------------------+-----------------------------------------| | i %L11=16 | Set serial port speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD PARITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L21=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the format of the parity bit. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | %L21=0 | No parity. | |------------------------+-----------------------------------| | %L21=3 | Use setting in @P3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD RECALL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L1=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 1, 32 - 126 | |--------------+---------------------------------------------| | Unit: | 1 ASCII character (see below for | | | exceptions) | |--------------+---------------------------------------------| | Description: | Sets the character for PAD recall. 0 | | | disables recall, and 1 sets it to the DLE | | | control character. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD SERVICE SIGNALS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L6=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects which PAD service signals will be | | | sent to the user. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | %L6=0 | No signals will be sent. | |---------------+--------------------------------------------| | %L6=1 | All signals except prompt will be sent. | |---------------+--------------------------------------------| | %L6=4 | Only prompt will be sent. | |---------------+--------------------------------------------| | %L6=5 | All signals will be sent. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PAD SERVICE SIGNAL DESTINATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %L19=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects where PAD service signals will be | | | sent. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | %L19=0 | Signals will not be sent. | |-----------------+------------------------------------------| | %L19=1 | Signals will be sent to the printer. | |-----------------+------------------------------------------| | i %L19=2 | Signals will be sent to the monitor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 PVC | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B5=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether X.25 will use Permanent | | | Virtual Channel. | |------------------------------------------------------------| | Command | Function | |-------------------------+----------------------------------| | i %B5=0 | X.25 PVC disabled. | |-------------------------+----------------------------------| | %B5=1 | X.25 PVC enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RECEIVE PACKET SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B2=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 7 - 10 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the received packets for | | | X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RECEIVE THROUGHPUT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B11=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the throughput for receiving X.25. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | i %B11=0 | Use network speed. | |---------------------+--------------------------------------| | %B11=3 | Throughput set to 75bps. | |---------------------+--------------------------------------| | %B11=4 | Throughput set to 110bps. | |---------------------+--------------------------------------| | %B11=5 | Throughput set to 300bps. | |---------------------+--------------------------------------| | %B11=6 | Throughput set to 600bps. | |---------------------+--------------------------------------| | %B11=7 | Throughput set to 1200bps. | |---------------------+--------------------------------------| | %B11=8 | Throughput set to 2400bps. | |---------------------+--------------------------------------| | %B11=9 | Throughput set to 4800bps. | |---------------------+--------------------------------------| | %B11=10 | Throughput set to 9600bps. | |---------------------+--------------------------------------| | %B11=11 | Throughput set to 19.2Kbps. | |---------------------+--------------------------------------| | %B11=12 | Throughput set to 48Kbps. | |---------------------+--------------------------------------| | %B11=13 | Throughput set to 64Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RECEIVE WINDOW SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B0=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 8 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the X.25 receive window. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RESET CODE | |------------------------------------------------------------| | Type: | Read-only | |--------------+---------------------------------------------| | Format: | AT [cmds] %B20? [cmds] | |--------------+---------------------------------------------| | Description: | Reports the reason for an X.25 reset. | |------------------------------------------------------------| | Value | Meaning | |---------------+--------------------------------------------| | 0 | Normal operation - no reset has occurred. | |---------------+--------------------------------------------| | 1 | DTE caused reset. | |---------------+--------------------------------------------| | 2 | Local procedure error occurred. | |---------------+--------------------------------------------| | 3 | Destination address is incompatible. | |---------------+--------------------------------------------| | 4 | Network is busy. | |---------------+--------------------------------------------| | 5 | Remote procedure error occurred. | |---------------+--------------------------------------------| | 6 | Cause of reset unknown. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RESET TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B99=n [cmds] | |--------------+---------------------------------------------| | Default: | 180 | |--------------+---------------------------------------------| | Range: | 0 - 600 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the reset timer for X.25 operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 RPOA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B14=xxxx [cmds] | |--------------+---------------------------------------------| | Description: | Sets the RPOA for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 TRANSMIT DELAY TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B19=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 65535 | |--------------+---------------------------------------------| | Unit: | 1ms | |--------------+---------------------------------------------| | Description: | Sets the delay time for X.25 transmission. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 TRANSMIT PACKET SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B3=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0, 7 - 10 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the transmitted packets | | | for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 TRANSMIT THROUGHPUT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B12=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the throughput for transmitting X.25. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i %B12=0 | Use network speed. | |-----------------------+------------------------------------| | %B12=3 | Throughput set to 75bps. | |-----------------------+------------------------------------| | %B12=4 | Throughput set to 110bps. | |-----------------------+------------------------------------| | %B12=5 | Throughput set to 300bps. | |-----------------------+------------------------------------| | %B12=6 | Throughput set to 600bps. | |-----------------------+------------------------------------| | %B12=7 | Throughput set to 1200bps. | |-----------------------+------------------------------------| | %B12=8 | Throughput set to 2400bps. | |-----------------------+------------------------------------| | %B12=9 | Throughput set to 4800bps. | |-----------------------+------------------------------------| | %B12=10 | Throughput set to 9600bps. | |-----------------------+------------------------------------| | %B12=11 | Throughput set to 19.2Kbps. | |-----------------------+------------------------------------| | %B12=12 | Throughput set to 48Kbps. | |-----------------------+------------------------------------| | %B12=13 | Throughput set to 64Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 TRANSMIT WINDOW SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B1=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 8 | |--------------+---------------------------------------------| | Unit: | N/A | |--------------+---------------------------------------------| | Description: | Sets the size of the X.25 transmit window. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 USER DATA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B18=xxxx [cmds] | |--------------+---------------------------------------------| | Description: | Sets miscellaneous user data for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | X.25 USER ID | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %B13=xxxx [cmds] | |--------------+---------------------------------------------| | Description: | Sets the network user ID for X.25. | +------------------------------------------------------------+ +------------------------------------------------------------+ | XON/XOFF PASS THROUGH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Xn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether XON and XOFF characters | | | will be sent to the remote modem. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i \X0 | XON/XOFF characters trapped. | |---------------+--------------------------------------------| | \X1 | XON/XOFF characters sent to remote modem. |