MOTOROLA, INC. ============== VOICESURFR 56K (INTERNAL) Card Type Modem (asynchronous) Chip Set Rockwell I/O Options Voice, speakerphone, microphone in, speaker out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC, K56+ Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Three-quarter length, full-height +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------+--------+-----------------------+--------| | Telephone line | CN1 | Microphone in or | CN3 | | | | speaker out | | |------------------+--------+-----------------------+--------| | Telephone line | CN2 | Microphone in or | CN4 | | | | speaker out | | |------------------------------------------------------------| | Note: It is not known which of CN1 and CN2 is the | | microphone in jack and which is the speaker out jack. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | #CID, +MS | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25 | |------------------------------------------------------------| | S26, S27, S28, S29, S30, S32, S33, S36, S38, S39, S40, | | S46, S48, S82, S86, S91, S92, S95 | |------------------------------------------------------------| | Note: See MHI help file for complete information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UNIDENTIFIED COMMANDS | |------------------------------------------------------------| | Command | Default | |-----------------------------+------------------------------| | +ES=nnn | 3,0,2 | |-----------------------------+------------------------------| | +ESA=nnnnnnnn | 0,0,0,0,0,0,0,0 | |-----------------------------+------------------------------| | +ITF=nn | 255,64 | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | 2 | |----------------+-------------------------------------------| | Range: | 0 - 43 | |----------------+-------------------------------------------| | Description: | Select automode, extended result code | | | format, and caller ID format. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | i 0 | Extended result codes controlled by | | | | S95. | | | 1 | | | | | Extended result codes set for | | | | single-line format. | |----------+-------+-----------------------------------------| | 1 | 0 | Auto-mode detection disabled | | | | | | | i 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted | | | | with the following protocols in order - | | | | V.FC, V.32bis, V.32, V.22bis, V.22 or | | | | Bell 212, V.21, and Bell 103 | |----------+-------+-----------------------------------------| | 3, 2 | i 00 | Enables CONNECT result codes to report | | | | DTE speed | | | 01 | | | | | Full reporting of CONNECT result codes | | | 10 | | | | | Enables CONNECT result codes to report | | | | DCE speed | |----------+-------+-----------------------------------------| | 5, 4 | i 00 | Caller ID disabled. | | | | | | | 01 | Caller ID displays formatted data. | | | | | | | 10 | Caller ID displays raw hexadecimal | | | | data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |---------------+--------------------------------------------| | Default: | 71 | |---------------+--------------------------------------------| | Range: | 0 - 71 | |---------------+--------------------------------------------| | Description: | Selects compression and auto-retrain. | |---------------+--------------------------------------------| | Bit | Value | Function | |-------+-------+--------------------------------------------| | 1, 0 | 00 | Data compression disabled. | | | | | | | 01 | MNP5 enabled. | | | | | | | 10 | V.42bis enabled. | | | | | | | i 11 | MNP5 and V.42bis enabled. | |-------+-------+--------------------------------------------| | 6, 2 | 00 | Auto-retrain disabled. | | | | | | | 01 | Auto-retrain enabled. | | | | | | | i 11 | Auto-fallback/fall-forward enabled. | |-------+-------+--------------------------------------------| | 5 - 3 | 000 | Not used. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#>;[cmds] | |--------------+---------------------------------------------| | Description: | Dials the telephone number indicated | | | according to any modifiers included in the | | | string. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number. | |--------------+---------------------------------------------| | DP | Pulse dialing enabled. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n. | |--------------+---------------------------------------------| | DT | Tone dialing enabled. | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection. | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register. | |--------------+---------------------------------------------| | D> | Transmit grounding pulse. | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quiet Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D& | Wait for prompt tone detection function | | | enabled. Waits for prompt tone for amount | | | of time specified by the S7 command. | |--------------+---------------------------------------------| | D* | Toggles calling tone on or off for this | | | call. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY BLACKLIST NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *B [cmds] | |--------------+---------------------------------------------| | Description: | Displays the list of all the numbers on the | | | blacklist and their statuses. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CHIPSET MANUFACTURER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #MFR? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the voice chipset manufacturer's | | | name. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CHIPSET MODEL NAME | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #MDL? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the model name of the modem's | | | voice chipset. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY CHIPSET REVISION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #REV? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the revision level of the modem's | | | voice chipset. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY DELAYED NUMBERS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] *D [cmds] | |--------------+---------------------------------------------| | Description: | Displays the list of all delayed numbers | | | and their statuses. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Displays ROM checksum. | |--------------+---------------------------------------------| | I2 | Tests and displays ROM checksum result. | |--------------+---------------------------------------------| | I3 | Displays firmware revision, model, and | | | interface. | |--------------+---------------------------------------------| | I4 | Displays product name. | |--------------+---------------------------------------------| | I5 | Displays country code. | |--------------+---------------------------------------------| | I6 | Displays data pump model and revision. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0 - 7 | |----------------+-------------------------------------------| | Description: | Selects which distinctive ring signals | | | the modem will respond to. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | 0 | Do not respond to distinctive ring type | | | | 1. | | | 1 | | | | | Respond to distinctive ring type 1. | |----------+-------+-----------------------------------------| | 1 | 0 | Do not respond to distinctive ring type | | | | 2. | | | 1 | | | | | Respond to distinctive ring type 2. | |----------+-------+-----------------------------------------| | 2 | 0 | Do not respond to distinctive ring type | | | | 3. | | | 1 | | | | | Respond to distinctive ring type 3. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #CLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects which mode the modem will operate | | | in. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #CLS=0 | Modem will operate in data mode. | |--------------+---------------------------------------------| | #CLS=1 | Modem will operate in fax class 1 mode. | |--------------+---------------------------------------------| | #CLS=8 | Modem will operate in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RPI CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +Hn [cmds] | |--------------+---------------------------------------------| | Description: | Configures the Rockwell Protocol Interface. | |------------------------------------------------------------| | Command | Function | |-----------------+------------------------------------------| | +H0 | RPI disabled. | |-----------------+------------------------------------------| | +H1 | RPI enabled and local serial port speed | | | set to 19.2Kbps. | |-----------------+------------------------------------------| | +H2 | RPI enabled and local serial port speed | | | set to 38.4Kbps. | |-----------------+------------------------------------------| | +H3 | RPI enabled and local serial port speed | | | set to 57.6Kbps. | |-----------------+------------------------------------------| | +H11 | RPI+ enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKERPHONE OPTIONS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #SPK=x,y,z [cmds] | |--------------+---------------------------------------------| | Description: | Sets various options for speakerphone | | | functions. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | x=0 | Microphone enabled. | |---------------+--------------------------------------------| | x=1 | Microphone disabled. | |---------------+--------------------------------------------| | x=2 | Microphone enabled with maximum gain, | | | speaker disabled. | |---------------+--------------------------------------------| | y | Default: | 5 | |---------------+--------------+-----------------------------| | | Range: | 0 - 16 | |---------------+--------------+-----------------------------| | | Unit: | -2 dBm | |---------------+--------------+-----------------------------| | | Description: | Sets the attenuation level | | | | for speaker output in voice | | | | mode. A value of 16 will | | | | mute the speaker. | |---------------+--------------------------------------------| | z=0 | Microphone gain set to 0 dBm. | |---------------+--------------------------------------------| | z=1 | Microphone gain set to 6 dBm. | |---------------+--------------------------------------------| | z=2 | Microphone gain set to 9.5 dBm. | |---------------+--------------------------------------------| | z=3 | Microphone gain set to 12 dBm. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE DETECTION | |------------------------------------------------------------| | Format: | AT [cmds] #VTD=x,y,z [cmds] | |----------------+-------------------------------------------| | Default: | x,y,z 63 | |----------------+-------------------------------------------| | Range: | 0 - 63 | |----------------+-------------------------------------------| | Description: | Sets which tones the tone detection will | | | report. | |----------------+-------------------------------------------| | Note: | The value of x sets the tone detection | | | modes in voice transmit mode, y sets them | | | in voice receive mode, and z sets them in | | | voice command mode. | |------------------------------------------------------------| | Bit | Value | Function | |---------+-------+------------------------------------------| | 0 | 0 | DTMF tones are not detected. | | | | | | | i 1 | DTMF tones are detected. | |------------------------------------------------------------| | 1 | 0 | V.25 1300Hz calling tone is not | | | | detected. | | | i | | | | 1 | V.25 1300Hz calling tone is detected. | |-------------+----+-----------------------------------------| | 2 | 0 | T.30 1100Hz fax tone is not detected. | | | | | | | i | T.30 1100Hz fax tone is detected. | | | 1 | | |-------------+----+-----------------------------------------| | 3 | 0 | V.25/T.30 2100Hz answer tone is not | | | | detected. | | | i | | | | 1 | V.25/T.30 2100Hz answer tone is | | | | detected. | |-------------+----+-----------------------------------------| | 4 | 0 | Bell 2225Hz answer tone is not | | | | detected. | | | i | | | | 1 | Bell 2225Hz answer tone is detected. | |-------------+----+-----------------------------------------| | 5 | 0 | Call progress tones are not detected. | | | | | | | i | Call progress tones are detected. | | | 1 | | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - DIRECT ENTRY | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS=[m, n, x] | |--------------+---------------------------------------------| | Range: | m 200-3000, n 200-3000, x 0-255 | |--------------+---------------------------------------------| | Unit: | m 1 Hz, n 1 Hz, x .1 second | |--------------+---------------------------------------------| | Description: | Generates a dual-frequency tone for | | | duration x at frequencies m and n. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - TIMED PHONE KEYS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS={a, n} | |--------------+---------------------------------------------| | Range: | a 0-9, A-D, #, *; x 0-255 | |--------------+---------------------------------------------| | Unit: | x .1 second | |--------------+---------------------------------------------| | Description: | Generates the DTMF tone for duration x for | | | the character a. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR - PHONE KEYS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTS=a | |--------------+---------------------------------------------| | Range: | 0-9, A-D, #, * | |--------------+---------------------------------------------| | Description: | Generates the DTMF tones for the characters | | | in the string for the duration set with | | | +VBT. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TONE GENERATOR LENGTH | |------------------------------------------------------------| | Format | AT [cmds] #VBT=n [cmds] | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0 - 40 | |--------------+---------------------------------------------| | Unit: | 0.1 second | |--------------+---------------------------------------------| | Description: | Sets the length of DTMF tones that are | | | generated. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE BUFFER SPACE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSK=n [cmds] | |--------------+---------------------------------------------| | Default: | 255 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | 1 byte | |--------------+---------------------------------------------| | Description: | Sets the amount of data the modem can send | | | into the buffer after the XOFF signal is | | | sent. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE DEVICE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VLS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the I/O device for the DSP chip. | |--------------+---------------------------------------------| | Note: | This modem may not support all options | | | listed below. The #VLS? command will | | | display the available options. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #VLS=0 | Telephone line and handset used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=1 | Telephone handset used for voice I/O. | |--------------+---------------------------------------------| | #VLS=2 | Internal speaker only used for voice I/O. | |--------------+---------------------------------------------| | #VLS=3 | External microphone only used for voice | | | I/O. | |--------------+---------------------------------------------| | #VLS=4 | Telephone line and handset used for voice | | | I/O; internal speaker enabled. | |--------------+---------------------------------------------| | #VLS=5 | Headset used for voice I/O. | |--------------+---------------------------------------------| | #VLS=6 | Speakerphone used for voice I/O. | |--------------+---------------------------------------------| | #VLS=7 | Handset muted by disconnecting handset or | | | speakerphone from telephone line. | |--------------+---------------------------------------------| | #VLS=8 | Connects caller ID relay for recording of | | | conversation over handset. | |--------------+---------------------------------------------| | #VLS=9 | Connects handset (or speakerphone) to DSP | | | chip for recording or playback. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - DISPLAY BUFFER SIZE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VBQ? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the size of the voice buffer. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - DISPLAY COMPRESSION TYPE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VCI? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the type of compression currently | | | in use. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE - LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #BDR=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 48 | |--------------+---------------------------------------------| | Unit: | 2400bps | |--------------+---------------------------------------------| | Description: | Sets the speed of the local serial port | | | when in voice mode. A value of 0 indicates | | | that the modem should auto-detect the | | | correct serial port speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RE-RING DETECT TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRA=n [cmds] | |--------------+---------------------------------------------| | Default: | 70 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 10 mS | |--------------+---------------------------------------------| | Description: | Sets the maximum time the modem will wait | | | for the remote station to ring again before | | | it assumes that it has gone off-hook. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RECEIVE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRX | |--------------+---------------------------------------------| | Description: | Commands the modem to begin receiving voice | | | data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE RING DETECT TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VRN=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Sets the maximum time the modem will wait | | | for the remote station to ring before it | | | assumes that it went off-hook before it | | | rang. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLE QUALITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VBS=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the number of bits per sample that | | | the modem records. | |--------------+---------------------------------------------| | Note: | This modem may not support all options | | | listed below. The #VBS? command will | | | display the available options. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #VBS=2 | Modem records 2 bits per sample in ADPCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=3 | Modem records 3 bits per sample in ADPCM | | | encoding. | |--------------+---------------------------------------------| | i #VBS=4 | Modem records 4 bits per sample in ADPCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=8 | Modem records 8 bits per sample in PCM | | | encoding. | |--------------+---------------------------------------------| | #VBS=16 | Modem records 16 bits per sample in PCM | | | encoding. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SAMPLING RATE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSR=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the sampling rate used when recording | | | voice signals. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i #VSR=7200 | Selects a sampling rate of 7.2KHz. | |--------------+---------------------------------------------| | #VSR=8000 | Selects a sampling rate of 8KHz. | |--------------+---------------------------------------------| | #VSR=11025 | Selects a sampling rate of 11.025KHz in PCM | | | encoding only. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SILENCE DETECTION TIME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSP=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | .1 second | |--------------+---------------------------------------------| | Description: | Sets the minimum amount of silence that the | | | modem will detect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE SILENCE DETECTION THRESHOLD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VSS=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the threshold of sensitivity that the | | | modem uses to determine silence detection. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | #VSS=0 | Silence detection disabled. | |--------------+---------------------------------------------| | #VSS=1 | Minimum silence detection sensitivity. | |--------------+---------------------------------------------| | #VSS=2 | Standard silence detection sensitivity. | |--------------+---------------------------------------------| | #VSS=3 | Maximum silence detection sensitivity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TIMING MARK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTM=n [cmds] | |--------------+---------------------------------------------| | Description: | Configures timing mark placement. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | #VTM=0 | Timing marks disabled. | |---------------------+--------------------------------------| | #VTM=1 | Timing marks enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #TL=hhhh [cmds] | |--------------+---------------------------------------------| | Default: | 3FFF | |--------------+---------------------------------------------| | Range: | 0000 - 7FFF | |--------------+---------------------------------------------| | Unit: | Unidentified (hexadecimal) | |--------------+---------------------------------------------| | Description: | Sets the transmission level for sending | | | audio in voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE TRANSMIT | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #VTX | |--------------+---------------------------------------------| | Description: | Commands the modem to begin transmitting | | | voice data. | +------------------------------------------------------------+ +------------------------------------------------------------+ | VOICE VOLUME LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #VGT=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the volume level when playing back | | | audio signals. | |------------------------------------------------------------| | Command | Function | |----------------------+-------------------------------------| | #VGT=128 | Low volume setting. | |----------------------+-------------------------------------| | i #VGT=129 | Medium volume setting. | |----------------------+-------------------------------------| | #VGT=130 | High volume setting. | |----------------------+-------------------------------------| | #VGT=131 | Highest volume setting. | +------------------------------------------------------------+