NEWCOM, INC. ============ 336IFXSP(C) Card Type Modem (asynchronous) Chipset Unidentified I/O Options Audio line out, microphone in, speaker out, voice, speakerphone Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus 16-bit ISA Card Size Full height, half length +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |----------------------+-------+---------------------+-------| | Telephone line out | CN1 | Headphone line out | CN4 | |----------------------+-------+---------------------+-------| | Telephone line in | CN2 | Speaker out | CN5 | |----------------------+-------+---------------------+-------| | Microphone in | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG-N-PLAY | |------------------------------------------------------------| | Setting | JP1/A | JP1/B | JP1/C | |--------------------+-------------+------------+------------| | i Enabled | Closed | Closed | Closed | |--------------------+-------------+------------+------------| | Disabled | Open | Open | Open | |------------------------------------------------------------| | Note: If Plug-N-Play mode is enabled, all other | | jumper settings must also be set for Plug-N-Play. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT SELECTION | |------------------------------------------------------------| | Setting |JP1/D |JP1/E |JP1/F |JP1/G |JP1/H |JP1/I |JP1/J | |-----------+------+------+------+------+------+------+------| | 3 | Open | Open | Open | Open | Open | Open |Closed| |-----------+------+------+------+------+------+------+------| | 4 | Open | Open | Open | Open | Open |Closed| Open | |-----------+------+------+------+------+------+------+------| | 5 | Open | Open | Open | Open |Closed| Open | Open | |-----------+------+------+------+------+------+------+------| | 7 | Open | Open | Open |Closed| Open | Open | Open | |-----------+------+------+------+------+------+------+------| | 10 |Closed| Open | Open | Open | Open | Open | Open | |-----------+------+------+------+------+------+------+------| | 11 | Open |Closed| Open | Open | Open | Open | Open | |-----------+------+------+------+------+------+------+------| | 12 | Open | Open |Closed| Open | Open | Open | Open | |-----------+------+------+------+------+------+------+------| | i |Closed|Closed|Closed|Closed|Closed|Closed|Closed| |Plug-N-Play| | | | | | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS SELECTION | |------------------------------------------------------------| | Setting | JP1/K | JP1/L | JP1/M | JP1/N | |---------------+-----------+----------+----------+----------| | 3F8h (COM1:) | Closed | Closed | Open | Open | |---------------+-----------+----------+----------+----------| | 2F8h (COM2:) | Closed | Open | Open | Closed | |---------------+-----------+----------+----------+----------| | 3E8h (COM3:) | Open | Closed | Closed | Open | |---------------+-----------+----------+----------+----------| | 2E8h (COM4:) | Open | Open | Closed | Closed | |---------------+-----------+----------+----------+----------| | i Plug-N-Play | Open | Open | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z | |------------------------------------------------------------| | &C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z | |------------------------------------------------------------| | %A, %C, %E, %G | |------------------------------------------------------------| | Special AT Commands | |------------------------------------------------------------| | -C, "H, -J, "O | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S25, S27 | |------------------------------------------------------------| | S30, S31, S33, S37 | |------------------------------------------------------------| | Note: See MHI help file for complete information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | IS-101 COMMANDS | |------------------------------------------------------------| | +V Commands | |------------------------------------------------------------| | +VBT, +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, | | +VIP, +VIT, +VLS, +VNH, +VRA, +VRN | |------------------------------------------------------------| | +VRX, +VSD, +VSM, +VSP, +VTD, +VTS, +VTX, #VSPS | |------------------------------------------------------------| | -S Commands | |------------------------------------------------------------| | -SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, | | -SSP, -SSQ, -SSR, -SSV | |------------------------------------------------------------| | Note: The functions of the IS-101 commands are | | unidentified. | +------------------------------------------------------------+ Proprietary AT Command Set +----------------------------------------------------------------+ | BREAK TYPE | |----------------------------------------------------------------| |Type: |Configuration | |------------------+---------------------------------------------| |Format: |AT [cmds] \Kn [cmds] | |------------------+---------------------------------------------| |Description: |Configures action of break signal. | |----------------------------------------------------------------| | Command |Break from DTE | Break from | Modem | Break from | | | | DTE |receives \B |remote modem| | |Reliable/Normal| | | | | | mode |Direct mode | | | |---------+---------------+------------+------------+------------| | \K0 |Enter command |Send break |Buffers |Buffers | | |mode, do not |to remote |cleared and |cleared and | | |send break to |modem |break sent |break sent | | |remote modem. |immediately,|to remote |to DTE. | | | |then enter |modem. | | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K1 |Buffers cleared|Send break |Buffers |Buffers | | |and break sent |to remote |cleared and |cleared and | | |to remote |modem |break sent |break sent | | |modem. |immediately.|to remote |to DTE. | | | | |modem. | | |---------+---------------+------------+------------+------------| | \K2 |Enter command |Send break |Send break |Send break | | |mode, do not |to remote |to remote |to DTE | | |send break to |modem |modem |immediately.| | |remote modem. |immediately,|immediately.| | | | |then enter | | | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K3 |Send break to |Send break |Send break |Send break | | |remote modem |to remote |to remote |to DTE | | |immediately. |modem |modem |immediately.| | | |immediately.|immediately.| | |---------+---------------+------------+------------+------------| | \K4 |Enter command |Send break |Send break |Break sent | | |mode, do not |to remote |to remote |with | | |send break to |modem |modem with |received | | |remote modem. |immediately,|transmitted |data to the | | | |then enter |data. |DTE. | | | |command | | | | | |mode. | | | |---------+---------------+------------+------------+------------| | \K5 |Send break with|Send break |Send break |Break sent | | |transmitted |to remote |to remote |with | | |data. |modem |modem with |received | | | |immediately.|transmitted |data to the | | | | |data. |DTE. | +----------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for | | | low-speed data calls. | |--------------+---------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | Modem will use ITU-T V.22 at 1200bps. | |--------------+---------------------------------------------| | i B1 | Modem will use Bell 212A at 1200bps. | |--------------+---------------------------------------------| | B2 | Modem will use ITU-T V.23 at 1200/75bps. | |--------------+---------------------------------------------| | B3 | Modem will use ITU-T V.23 at 75/1200bps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Displays chip firmware revision. | |--------------+---------------------------------------------| | I2 | Tests and displays ROM checksum result. | |--------------+---------------------------------------------| | I3 | Displays modem chipset name. | |--------------+---------------------------------------------| | I5 | Displays hardware configuration. | |--------------+---------------------------------------------| | I6 | Displays country code. | |--------------+---------------------------------------------| | I7 | Displays board firmware revision. | |--------------+---------------------------------------------| | I8 | Displays chipset feature bitmap. | |--------------+---------------------------------------------| | I10 | Displays board feature bitmap. | |--------------+---------------------------------------------| | I11 | Displays board feature bitmap. | |--------------+---------------------------------------------| | I14 | Displays digital SAFE device information. | |--------------+---------------------------------------------| | I20 | Displays the revision level of the modem's | | | voice chipset. | |--------------+---------------------------------------------| | I21 | Displays the revision level of the modem's | | | voice firmware. | |--------------+---------------------------------------------| | I22 | Displays the voice chipset manufacturer's | | | name. | |--------------+---------------------------------------------| | I23 | Displays the model name of the modem's | | | voice chipset. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Vn [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &V0 | Displays stored profile 0. | |--------------+---------------------------------------------| | &V1 | Displays stored profile 1. | |--------------+---------------------------------------------| | &V3 | Displays relay status and I/O information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Wn [cmds] | |--------------+---------------------------------------------| | Description: | Selects which result codes the modem will | | | report. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i W0 | Enables CONNECT result codes to report DTE | | | speed. | |--------------+---------------------------------------------| | W1 | Enables CONNECT result codes to report DTE | | | speed. | |--------------+---------------------------------------------| | W2 | Enables CONNECT result codes to report DCE | | | speed. | |--------------+---------------------------------------------| | W3 | Enables CONNECT result codes to report DTE | | | speed with error correction and compression | | | information. | |--------------+---------------------------------------------| | W4 | Enables CONNECT result codes to report DTE | | | speed with modulation protocol, error | | | correction, and compression information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MODE SELECTION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] +FCLASS=n | |--------------+---------------------------------------------| | Description: | Sets what mode the modem will operate in. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | +FCLASS=0 | Data mode. | |--------------+---------------------------------------------| | +FCLASS=1 | Class 1 fax mode. | |--------------+---------------------------------------------| | +FCLASS=8 | Voice mode. | |--------------+---------------------------------------------| | +FCLASS=80 | IS-101 voice mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRELLIS CODING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Un [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem will use trellis | | | coding. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i &U0 | Trellis coding enabled. | |-----------------------+------------------------------------| | &U1 | Trellis coding disabled. | +------------------------------------------------------------+