MAXTECH CORPORATION =================== XPV 336I (VF-1133HV/R9) Card Type Modem/Fax card Chip Set Unidentified I/O Options Line in(RJ-11), line out(RJ-11) Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, V.FC Fax Modulation ITU-T V.17, V.27ter, V.29, V.21 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 8-bit ISA +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | RJ-11 line | CN1 | RJ-11 line | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | JP6/A | JP6/B | JP6/C | |-----------------------+------------+-----------+-----------| | COM1 (3F8h) | Open | Closed | Closed | |-----------------------+------------+-----------+-----------| | COM2 (2F8h) | Open | Open | Closed | |-----------------------+------------+-----------+-----------| | COM3 (3E8h) | Open | Closed | Open | |-----------------------+------------+-----------+-----------| | COM4 (2E8h) | Open | Open | Open | |-----------------------+------------+-----------+-----------| |>> Plug & Play enabled | Closed | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | Setting | JP6/D | JP6/E | JP6/F | JP6/G | |-----------------------+---------+--------+--------+--------| | IR/FONT> | Closed | Open | Open | Open | |-----------------------+---------+--------+--------+--------| | IRQ3 | Open | Closed | Open | Open | |-----------------------+---------+--------+--------+--------| | IRQ4 | Open | Open | Closed | Open | |-----------------------+---------+--------+--------+--------| | IRQ5 | Open | Open | Open | Closed | |-----------------------+---------+--------+--------+--------| |>> Plug & Play enabled | Open | Closed | Open | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, +++, A/ | |------------------------------------------------------------| | A, E, H, M, O, P, T, V, X, Y, Z | |------------------------------------------------------------| | &C, &G, &L, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z | |------------------------------------------------------------| | %A | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22 | |------------------------------------------------------------| | S23, S25, S26, S27, S28 | |------------------------------------------------------------| | Voice Mode Commands | |------------------------------------------------------------| | #BDR, #CLS, #MDL?, #MFR?, #REV?, #VBQ?, #VBS, #VBT, #VCI?, | | #VLS, #VRA, #VRN, #VRX, #VSD | |------------------------------------------------------------| | #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ PROPRIETARY AT COMMAND SET +------------------------------------------------------------+ | AUTO-FALLFORWARD/FALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &En [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables auto fallforward/fallback | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| |>> &E0 | Auto fallforward/fallback disabled | |--------------+---------------------------------------------| | &E1 | Auto fallforward/fallback enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | CCITT mode | |--------------+---------------------------------------------| |>> B1 | Bell 212A at 300 or 1200bps | |--------------+---------------------------------------------| | B2 | Autoscan mode | |--------------+---------------------------------------------| | B3 | CCITT V.23 mode | |--------------+---------------------------------------------| | B4 | 300bps | |--------------+---------------------------------------------| | B5 | 1200bps | |--------------+---------------------------------------------| | B6 | 2400bps | |--------------+---------------------------------------------| | B7 | 4800bps | |--------------+---------------------------------------------| | B8 | 9600bps | |--------------+---------------------------------------------| | B9 | 14400bps | |--------------+---------------------------------------------| | B10 | 16800bps | |--------------+---------------------------------------------| | B11 | 19200bps | |--------------+---------------------------------------------| | B12 | 21600bps | |--------------+---------------------------------------------| | B13 | 28800bps | |--------------+---------------------------------------------| | B14 | 31200bps | |--------------+---------------------------------------------| | B15 | 33600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i&S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i&D0 | DTR override | |--------------+---------------------------------------------| | &D1 | DTR toggle causes online command mode | |--------------+---------------------------------------------| | &D2 | Normal DTR operations | |--------------+---------------------------------------------| | &D3 | Resets on receipt of DTR | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i&F0 | Factory default profile with | | | V.42bis/hardware flow control enabled | |--------------+---------------------------------------------| | &F1 | Factory default profile with software flow | | | control enabled | |--------------+---------------------------------------------| | &F2 | Factory default profile with | | | V.42bis/hardware flow control enabled | |--------------+---------------------------------------------| | &F3 | Factory default profile with software flow | | | control enabled (Macintosh) | |--------------+---------------------------------------------| | &F4 | Factory default profile with | | | V.42bis/hardware flow control enabled | | | (Macintosh) | |--------------+---------------------------------------------| | &F5 | Factory default profile with | | | V.42bis/hardware flow control disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | HELP SCREEN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &H [cmds] | |--------------+---------------------------------------------| | Description: | Displays help screen | +------------------------------------------------------------+ +------------------------------------------------------------+ | ORIGINATE MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &On [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables originate-only mode | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &O0 | Originate-only mode disabled | |--------------+---------------------------------------------| | &O1 | Originate-only mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i&P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports four digit product code | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Reports internal memory test | |--------------+---------------------------------------------| | I3 | V.42bis ID | |--------------+---------------------------------------------| | I4 | Reports internal ID | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| |>> Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | Result code sending disabled in answer mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| |>> L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ EXTENDED AT COMMAND SET +------------------------------------------------------------+ | AUTODETECT V.34 & V.FC | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls autodetect for V.34 and V.FC | | | negotiation signals | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %M0 | V.34 and V.FC autodetect enabled | |--------------+---------------------------------------------| | %M1 | V.34 autodetect enabled | |--------------+---------------------------------------------| | %M2 | V.FC autodetect enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | %E1 | Auto-retrain enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALL-BACK SECURITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects call-back security password options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %S0 | Call-back security disabled | |--------------+---------------------------------------------| | %S1 | Password check only enabled | |--------------+---------------------------------------------| | %S2 | Call-back security with password check | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR-DOWN SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables clear-down signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %D0 | Clear-down signal disabled | |--------------+---------------------------------------------| | %D1 | Clear-down signal enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | MNP5 enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP mode enabled | |--------------+---------------------------------------------| | \N3 | MNP or Normal mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 mode enabled | |--------------+---------------------------------------------| | \N5 | V.42 or MNP reliable mode enabled | |--------------+---------------------------------------------| | \N6 | V.42/MNP/Normal mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Reports DCE speed; extended result codes | | | disabled | |--------------+---------------------------------------------| |>> \V1 | Reports DCE speed; extended result codes | | | enabled | |--------------+---------------------------------------------| | \V2 | Reports DTE speed; extended result codes | | | disabled | |--------------+---------------------------------------------| | \V3 | Reports DTE speed; extended result codes | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %L [cmds] | |--------------+---------------------------------------------| | Range: | 0-15 | |--------------+---------------------------------------------| | Unit: | -1 dBm | |--------------+---------------------------------------------| | Description: | Sets transmit level. Default=12 | +------------------------------------------------------------+ +------------------------------------------------------------+ | POWER-ON AUTO-CONNECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Pn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables power-on auto-connect | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %P0 | Power-on auto-connect disabled | |--------------+---------------------------------------------| | %P1 | Power-on auto-connect enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORED PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \P=n [cmds] | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Stores password with a maximum of seven | | | characters in NVRAM. \P=? displays stored | | | password | +------------------------------------------------------------+