MAXTECH CORPORATION =================== XPVS288R9 (SF-1128HV/R9) Card Type Modem, Fax Chip Set Unidentified I/O Options Line in, line out, microphone in, speaker out Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, full-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Microphone in | CN3 | |--------------------------+----------+---------------+------| | Line in | CN2 | Speaker out | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | USER CONFIGURABLE SETTINGS | |------------------------------------------------------------| | Setting | Label | Position | |-------------------------------+--------+-------------------| | Microphone set for dynamic | JP2 | Pins 1 & 2 closed | |-------------------------------+--------+-------------------| | Microphone set for condenser | JP2 | Pins 2 & 3 closed | |-------------------------------+--------+-------------------| | Speaker set for stereo | JP4 | Closed | |-------------------------------+--------+-------------------| | Speaker set for mono | JP4 | Open | |-------------------------------+--------+-------------------| | i Plug and Play enabled | PNP1 | Closed | |-------------------------------+--------+-------------------| | Plug and Play disabled | PNP1 | Open | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | PNP1 | SW1/1 | SW1/2 | |---------------+---------------+--------------+-------------| | COM1 (3F8h) | Open | On | On | |---------------+---------------+--------------+-------------| | COM2 (2F8h) | Open | Off | On | |---------------+---------------+--------------+-------------| | COM3 (3E8h) | Open | On | Off | |---------------+---------------+--------------+-------------| | COM4 (2E8h) | Open | Off | Off | |---------------+---------------+--------------+-------------| | i PnP | Closed | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | IRQ SETTINGS | |------------------------------------------------------------| | Setting | PNP1 | SW1/3 | SW1/4 | SW1/5 | SW1/6 | |-----------+----------+---------+---------+--------+--------| | 2/9 | Open | On | Off | Off | Off | |-----------+----------+---------+---------+--------+--------| | 3 | Open | Off | On | Off | Off | |-----------+----------+---------+---------+--------+--------| | 4 | Open | Off | Off | On | Off | |-----------+----------+---------+---------+--------+--------| | 5 | Open | Off | Off | Off | On | |-----------+----------+---------+---------+--------+--------| | i PnP | Closed | Off | Off | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, E, H, M, O, P, T, V, X, Y, Z | |------------------------------------------------------------| | &C, &G, &L, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z | |------------------------------------------------------------| | %A | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S25, S26, | |------------------------------------------------------------| | S27 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | #BDR, #CLS, #MDL?, #MFR?, #REV?, #SPK=a,b,c, #VBQ?, #VBS, | | #VBT, #VCI?, #VLS, #VRA, #VRN, | |------------------------------------------------------------| | #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &M0 | Asynchronous mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | Enables CCITT mode | |--------------+---------------------------------------------| | B1 | Enables Bell mode | |--------------+---------------------------------------------| | B2 | Enables Autoscan mode | |--------------+---------------------------------------------| | B3 | Enables CCITT V.23 mode only | |--------------+---------------------------------------------| | B4 | Enables 300 bps connection only | |--------------+---------------------------------------------| | B5 | Enables 1200 bps connection only | |--------------+---------------------------------------------| | B6 | Enables 2400 bps connection only | |--------------+---------------------------------------------| | B7 | Enables 4800 bps connection only | |--------------+---------------------------------------------| | B8 | Enables 9600 bps connection only | |--------------+---------------------------------------------| | B9 | Enables 14400 bps connection only | |--------------+---------------------------------------------| | B10 | Enables 16800 bps connection only | |--------------+---------------------------------------------| | B11 | Enables 19200 bps connection only | |--------------+---------------------------------------------| | B12 | Enables 21600 bps connection only | |--------------+---------------------------------------------| | B13 | Enables 24000 bps connection only | |--------------+---------------------------------------------| | B14 | Enables 26400 bps connection only | |--------------+---------------------------------------------| | B15 | Enables 28800 bps connection only | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Command 0 | Modem does not respond to DTR | |--------------+---------------------------------------------| | Command 1 | Modem goes to command mode after DTR goes | | | is off | |--------------+---------------------------------------------| | Command 2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |--------------+---------------------------------------------| | Command 3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Fn [cmds] | |--------------+---------------------------------------------| | Description: | Recalls factory default configuration | | | and/or with software flow control enabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Recalls factory default configuration | |--------------+---------------------------------------------| | &F1 | Recalls factory default configuration with | | | software flow control enabled | |--------------+---------------------------------------------| | &F2 | Recalls factory default configuration with | | | hardware flow control enabled | |--------------+---------------------------------------------| | &F3 | Recalls factory default configuration with | | | software flow control enabled and ignores | | | the DTR signal | |--------------+---------------------------------------------| | &F4 | Recalls factory default configuration with | | | hardware flow control enabled and ignores | | | the DTR signal | |--------------+---------------------------------------------| | &F5 | Set modem to Direct mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | FALL FORWARD/FALL BACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &En [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables fall forward/fall back | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &E0 | Disables automatic fall forward/fall back | |--------------+---------------------------------------------| | &E1 | Enables automatic fall forward/fallback | +------------------------------------------------------------+ +------------------------------------------------------------+ | HELP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &H [cmds] | |--------------+---------------------------------------------| | Description: | Displays the modem help screen | +------------------------------------------------------------+ +------------------------------------------------------------+ | ORIGINATE MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &On [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables originate-only mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &O0 | Originate-only mode disabled | |--------------+---------------------------------------------| | &O1 | Originate-only mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe & Hong Kong) | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested and | | | configures Plug and Play serial number | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product ID | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports internal memory | |--------------+---------------------------------------------| | I3 | Reports V.42bis ID | |--------------+---------------------------------------------| | I4 | Reports internal ID | |--------------+---------------------------------------------| | I99=n | Configures Plug and Play serial number to n | | | (n = 0-225) | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Qn [cmds] | |--------------+---------------------------------------------| | Description: | Enables modem to send result codes to the | | | DTE | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i Q0 | Result code sending enabled | |--------------+---------------------------------------------| | Q1 | Result code sending disabled | |--------------+---------------------------------------------| | Q2 | Result code sending disabled only when | | | answer mode is enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | i L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ Extended AT Command Set +------------------------------------------------------------+ | AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %En [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain mode and | | | fallback/fall-forward | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %E0 | Auto-retrain disabled | |--------------+---------------------------------------------| | i %E1 | Auto-retrain enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-DETECT SETTINGS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Mn [cmds] | |--------------+---------------------------------------------| | Description: | Controls V.34 and V.FC while in auto-detect | | | mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %M0 | Sets V.34 and V.FC to auto-detect mode | |--------------+---------------------------------------------| | %M1 | Sets only V.34 to auto-detect | |--------------+---------------------------------------------| | %M2 | Sets only V.FC to auto-detect | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR-DOWN SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Dn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables clear-down signal | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %D0 | Clear-down signal disabled | |--------------+---------------------------------------------| | i %D1 | Clear-down signal enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION/CORRECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression and correction | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression and correction disabled | |--------------+---------------------------------------------| | %C1 | MNP5 and V.42bis; or data compression and | | | correction enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | MNP reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode or MNP auto-reliable | | | mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | |--------------+---------------------------------------------| | \N5 | V.42 auto-reliable mode or MNP | | | auto-reliable mode enabled | |--------------+---------------------------------------------| | \N6 | V.42/MNP/Normal data link enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Reports DCE speed and extended responses | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \V0 | Reports DCE speed without sending extended | | | responses | |--------------+---------------------------------------------| | \V1 | Reports DCE speed and send sends extended | | | responses | |--------------+---------------------------------------------| | \V2 | Reports DTE speed without sending extended | | | responses | |--------------+---------------------------------------------| | \V3 | Reports DTE speed and send sends extended | | | responses | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE SIGNAL LEVEL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Ln [cmds] | |--------------+---------------------------------------------| | Default: | 11 | |--------------+---------------------------------------------| | Range: | 0-15 | |--------------+---------------------------------------------| | Unit: | dBm | |--------------+---------------------------------------------| | Description: | Returns a value which indicates the | | | received line signal level | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \P=x [cmds] | |--------------+---------------------------------------------| | Description: | Stores password x (x=ASCII characters 1 | | | through 127 excluding "?" maximum 7 | | | characters) stored into non-volatile RAM | +------------------------------------------------------------+ +------------------------------------------------------------+ | POWER-ON AUTO-CONNECT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Pn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables power-on auto-connect | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %P0 | Power-on auto-connect disabled | |--------------+---------------------------------------------| | %P1 | Power-on auto-connect enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Sn [cmds] | |--------------+---------------------------------------------| | Description: | Enables/Disables call-back security and | | | checks password | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i %S0 | Call-back security disabled | |--------------+---------------------------------------------| | %S1 | Password check enabled | |--------------+---------------------------------------------| | %S2 | Call-back security and password check | | | enabled | +------------------------------------------------------------+ S(status) -Registers +------------------------------------------------------------+ | BIT-MAPPED REGISTER S28 | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Configures Power-on auto-connect, security | | | call-back, auto-retrain, and Bell/CCITT | | | mode settings | +------------------------------------------------------------+