MOTOROLA, INC ============= MOBILESURFR 56K Card Type Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212 Protocol ITU-T V.34, V.32bis, V.32, V.22bis, V.22, V.21, K56flex Fax Modulation ITU-T V.17, V.29, V.27ter, V.21 channel Protocol 2 Error V.42, V.42bis, MNP5, MNP10, MNP10EC Correction/Compression Fax Class Unidentified Data Bus PCMCIA Type II 54912 +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, '+++', A/ | |------------------------------------------------------------| | A, B, E, H, M, O, Q, V, W, X, Y, Z | |------------------------------------------------------------| | &C, &P, &R, &T, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, \V | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, | |------------------------------------------------------------| | S26, S27, S28, S30, S31, S32, S33, S36, S38, S39, S40, | | S41, S46, S48, S82, S86, S91, S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | -K, #CID, +MS | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Automode detection disable | |--------------+---------------------------------------------| | i N1 | Automode detection enable | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |---------------+--------------------------------------------| | Description: | Selects modem response to DTR | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | &D0 | Modem does not respond to DTR | |---------------+--------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |---------------+--------------------------------------------| | i &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |---------------+--------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Load factory setting 0 | |--------------+---------------------------------------------| | &F1 | Load factory setting 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | Bi-directional RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | Bi-directional XON/XOFF flow control | | | enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS and XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code | |--------------+---------------------------------------------| | I1 | Reports EPROM CRC value | |--------------+---------------------------------------------| | I2 | Displays OK | |--------------+---------------------------------------------| | I3 | Reports firmware revision number | |--------------+---------------------------------------------| | I4 | Reports Motorola 56K | |--------------+---------------------------------------------| | I5 | Reports country code parameter | |--------------+---------------------------------------------| | I6 | Reports data pump model and code revision | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Mn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various speaker options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | M0 | Speaker disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Speaker disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the transmit carrier switching | |------------------------------------------------------------| | Note: Command performs no function; included for | | compatibility only. | +------------------------------------------------------------+ Special AT Commands +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls distinctive ring | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SDR=0 | Distinctive ring disable | |--------------+---------------------------------------------| | -SDR=1 | Distinctive ring enable ring type A | |--------------+---------------------------------------------| | -SDR=2 | Distinctive ring enable ring type B | |--------------+---------------------------------------------| | -SDR=3 | Distinctive ring enable ring type A and B | |--------------+---------------------------------------------| | -SDR=4 | Distinctive ring enable ring type C | |--------------+---------------------------------------------| | -SDR=5 | Distinctive ring enable ring type A and C | |--------------+---------------------------------------------| | -SDR=6 | Distinctive ring enable ring type B and C | |--------------+---------------------------------------------| | -SDR=7 | Distinctive ring enable ring type A, B, and | | | C | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10-EC | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SECn [cmds] | |--------------+---------------------------------------------| | Description: | Controls MNP10-EC | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SEC0 | Disable | |--------------+---------------------------------------------| | -SEC1 | Enable and set TX level (0-30dB/m) | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | AUTO-SYNC OPTIONS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the auto-sync options | +------------------------------------------------------------+ +------------------------------------------------------------+ | HDLC ADDRESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sets the HDLC address or BSC sync character | +------------------------------------------------------------+