PARADYNE CORPORATION ==================== COMSPHERE 3825PLUS Modem Type Data (synchronous/asynchronous)/Fax Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I & II Data Modulation AT&T V.32terbo Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Purpose | Location | Purpose | Location | |------------------+----------+-------------------+----------| | Line out | CN1 | DC power | CN4 | |------------------+----------+-------------------+----------| | Line in | CN2 | Power switch | SW1 | |------------------+----------+-------------------+----------| | RS-232/422 | CN3 | | | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |--------+-------+------------+------------------------------| | EC/SQ | Green | On | Error correction enabled | |--------+-------+------------+------------------------------| | EC/SQ | Green | Off | Error correction disabled | |--------+-------+------------+------------------------------| | EC/SQ | Green | Blinking, | Error correction activated | | | | mostly on | and poor line signal errors | | | | | detected | |--------+-------+------------+------------------------------| | EC/SQ | Green | Blinking, | Error correction not | | | | mostly off | activated and poor line | | | | | signal errors detected | |--------+-------+------------+------------------------------| | HS/RI | Green | On | Modem is operating at | | | | | highest configured speed | |--------+-------+------------+------------------------------| | HS/RI | Green | Off | Modem is operating at less | | | | | than highest configured | | | | | speed | |--------+-------+------------+------------------------------| | HS/RI | Green | Blinking | Phone is ringing | |--------+-------+------------+------------------------------| | CD | Green | On | Carrier signal detected | |--------+-------+------------+------------------------------| | CD | Green | Off | Carrier signal not detected | |--------+-------+------------+------------------------------| | OH/APL | Green | On | Modem is off-hook | |--------+-------+------------+------------------------------| | OH/APL | Green | Off | Modem is on-hook | |--------+-------+------------+------------------------------| | OH/APL | Green | Blinking | Modem set for leased line | |--------+-------+------------+------------------------------| | RD | Green | On | Modem is receiving data | |--------+-------+------------+------------------------------| | RD | Green | Off | Modem is not receiving data | |--------+-------+------------+------------------------------| | SD | Green | On | Modem is transmitting data | |--------+-------+------------+------------------------------| | SD | Green | Off | Modem is not transmitting | | | | | data | |--------+-------+------------+------------------------------| | TR | Green | On | DTR signal is high or modem | | | | | is set to ignore signal | |--------+-------+------------+------------------------------| | TR | Green | Off | DTR signal is low | |--------+-------+------------+------------------------------| | MR/PWR | Green | Off | Power is off | |--------+-------+------------+------------------------------| | MR/PWR | Green | On | Power is on | |--------+-------+------------+------------------------------| | MR/PWR | Green | Blinking, | Download only mode | | | | slow | | |--------+-------+------------+------------------------------| | MR/PWR | Green | Blinking, | Cloning mode | | | | fast | | |--------+-------+------------+------------------------------| | MR/PWR | Green | Blinking | Power on in leased mode | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AT COMMAND RESPONSE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S84=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S84=0 &W | |--------------+---------------------------------------------| | Description: | Sets the response to AT commands. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S84=0 | Normal operation | |--------------+---------------------------------------------| | S84=1 | Execute valid commands, suppress error | | | codes. | |--------------+---------------------------------------------| | S84=2 | Ignore configuration commands, always | | | return OK error code. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO BAUD | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S78=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S78=0 &W | |--------------+---------------------------------------------| | Description: | Allows modem to connect at remote modem's | | | modulation. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S78=0 | Auto baud enabled. | |--------------+---------------------------------------------| | S78=1 | Auto baud disabled. | |--------------+---------------------------------------------| | S78=2 | PBX operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] %An [cmds] | |--------------+---------------------------------------------| | Example: | AT%A20 | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used as the | | | auto-reliable fallback character. %A0 will | | | disable this function. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE TIME BUFFER CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Example: | AT \C1 &W | |--------------+---------------------------------------------| | Description: | Controls the handling of incoming data | | | during auto-reliable time period. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \CO | Data is discarded. | |--------------+---------------------------------------------| | \C1 | Data is buffered. | |--------------+---------------------------------------------| | \C2 | Data is discarded, resets to \C1 on receipt | | | of autoreliable fallback character. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |--------------+---------------------------------------------| | Example: | AT \K5 &W | |--------------+---------------------------------------------| | Description: | Selects response to DTE break command. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \K0 | Send break, clear buffer, enter command | | | mode. | |--------------+---------------------------------------------| | \K1 | Send break, clear buffer | |--------------+---------------------------------------------| | \K2 | Send break, send data, enter command mode. | |--------------+---------------------------------------------| | \K3 | Send break. send data, | |--------------+---------------------------------------------| | \K4 | Send data, send break, enter command mode. | |--------------+---------------------------------------------| | i \K5 | Send data, send break. | |--------------+---------------------------------------------| | \K6 | Disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BUSY OUT ON LOW DTR | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S69=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S69=0 &W | |--------------+---------------------------------------------| | Description: | Modem goes off hook on low DTR (use only in | | | PBX mode). | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S69=0 | Busy out disabled. | |--------------+---------------------------------------------| | S69=1 | Busy out enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CD SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Example: | AT &C3 | |--------------+---------------------------------------------| | Description: | Configures the behavior of the carrier | | | detect signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &C0 | CD forced high. | |--------------+---------------------------------------------| | i &C1 | CD normal. | |--------------+---------------------------------------------| | &C2 | CD forced high except during handshaking | | | and disconnecting. | |--------------+---------------------------------------------| | &C3 | CD momentary interrupt on disconnect. | |--------------+---------------------------------------------| | &C4 | CD follows remote RTS signal. | |--------------+---------------------------------------------| | &C5 | CD Follows DTR signal. Forced low on | | | disconnect. | |--------------+---------------------------------------------| | &C6 | CD forced low on retrain of over 10 sec. | | | Forced high after no retrain for over 10 | | | sec. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CELLULAR ENHANCEMENTS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S91=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S91=0 &W | |--------------+---------------------------------------------| | Description: | Configures modem to enhanced cellular mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S91=0 | Disabled | |--------------+---------------------------------------------| | S91=1 | Enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CLEAR ERROR BUFFER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] "F [cmds] | |--------------+---------------------------------------------| | Example: | AT "F &W | |--------------+---------------------------------------------| | Description: | Empties error buffer. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT %Cn | |--------------+---------------------------------------------| | Example: | AT I2 %C1 &B0 | |--------------+---------------------------------------------| | Description: | Selects data compression. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled. | |--------------+---------------------------------------------| | i %C1 | Data compression enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Dn [cmds] | |--------------+---------------------------------------------| | Example: | AT \D0 | |--------------+---------------------------------------------| | Description: | Selects the function of the CTS signal. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \D0 | CTS forced high. | |--------------+---------------------------------------------| | \D1 | CTS normal. | |--------------+---------------------------------------------| | \D2 | CTS interrupted for 2 seconds on | | | disconnect. | |--------------+---------------------------------------------| | \D3 | CTS follows DTR. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT BUFFER DELAY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S39=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S39=0 | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Selects how long the modem will continue to | | | transmit data in receive buffer after | | | receipt of disconnect signal | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT BUFFER DELAY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S49=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S49=0 | |--------------+---------------------------------------------| | Default: | 10 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Selects how long the modem will continue to | | | transmit data in transmit buffer after | | | receipt of disconnect signal | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT IMMEDIATELY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S85=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S85=0 &W | |--------------+---------------------------------------------| | Description: | Disconnect immediately on receipt of | | | disconnect signal from DTE or diagnostic | | | control panel. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S85=0 | Disabled. | |--------------+---------------------------------------------| | S85=1 | Enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT INACTIVITY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S80=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S80=3 &W | |--------------+---------------------------------------------| | Description: | Sets the signal monitored by the inactivity | | | timer (\T). | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S80=0 | Transmit or receive. | |--------------+---------------------------------------------| | S80=1 | Transmit only. | |--------------+---------------------------------------------| | S80=2 | Receive only. | |--------------+---------------------------------------------| | i S80=3 | Transmit and receive. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISCONNECT ON LOSS OF CURRENT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S65=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S65=0 | |--------------+---------------------------------------------| | Description: | Causes the modem to disconnect if the | | | telephone line's current drops. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S65=0 | Disconnect after 8ms if current is lost. | |--------------+---------------------------------------------| | S65=1 | Disconnect after 90ms if current is lost. | |--------------+---------------------------------------------| | S65=2 | Disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Example: | AT \G1 &K3 | |--------------+---------------------------------------------| | Description: | Selects modem port flow control. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \G0 | Flow control disabled. | |--------------+---------------------------------------------| | \G1 | Flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Example: | AT \Q5 | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled. | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control | | | enabled. | |--------------+---------------------------------------------| | \Q2 | CTS flow control by DCE enabled. | |--------------+---------------------------------------------| | i \Q3 | Bidirectional CTS/RTS flow control enabled. | |--------------+---------------------------------------------| | \Q4 | XON/XOFF flow control by DCE enabled. | |--------------+---------------------------------------------| | \Q5 | XON/XOFF flow control by DTE enabled. | |--------------+---------------------------------------------| | \Q6 | RTS flow control by DTE enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Example: | AT\T20 | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LAP-M FRAME SIZE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Example: | AT \A3 %C1 | |--------------+---------------------------------------------| | Description: | Sets the maximum frame size for V.42 and | | | MNP connections. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | Maximum frame size is 64 | |--------------+---------------------------------------------| | \A1 | Maximum frame size is 128 | |--------------+---------------------------------------------| | \A2 | Maximum frame size is 192 | |--------------+---------------------------------------------| | i \A3 | Maximum frame size is 256 | |--------------+---------------------------------------------| | \A4 | Maximum frame size is 32 | |--------------+---------------------------------------------| | \A5 | Maximum frame size is 16 | |------------------------------------------------------------| | Note: Maximum V.42 frame size is 128. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LAP-M FRAME WINDOW | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S89=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS89=6 | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 1-9 | |--------------+---------------------------------------------| | Unit: | 1 frame (beginning with 1=6 frames, 0=auto | | | adjust) | |--------------+---------------------------------------------| | Description: | Sets the number of frames used in V.42 and | | | V.42bis transmissions | +------------------------------------------------------------+ +------------------------------------------------------------+ | LEASED LINE AUTO-RETRAIN | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S82=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S82=0 &W | |--------------+---------------------------------------------| | Description: | Allows modem to retrain to compensate for | | | bad line quality in V.32bis, V.32terbo or | | | V.34 mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S82=0 | Retrain enabled. | |--------------+---------------------------------------------| | S82=1 | Retrain disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LEASED LINE DISCONNECT LEVEL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S48=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S48=0 &W | |--------------+---------------------------------------------| | Description: | Sets level carrier signal drops to before | | | disconnect. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S48=0 | Disconnect at -43dBm | |--------------+---------------------------------------------| | S48=1 | Disconnect at -26dBm | +------------------------------------------------------------+ +------------------------------------------------------------+ | LEASED LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S44=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS44=6 | |--------------+---------------------------------------------| | Default: | 27 | |--------------+---------------------------------------------| | Description: | Sets maximum leased line speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S44=1 | 14.4Kbps V.32bis | |--------------+---------------------------------------------| | S44=2 | 12.0Kbps V.32bis | |--------------+---------------------------------------------| | S44=3 | 9600bps V.32bis, V.32 | |--------------+---------------------------------------------| | S44=4 | 7200bps V.32bis | |--------------+---------------------------------------------| | S44=5 | 4800bps V.32bis, V.32 | |--------------+---------------------------------------------| | S44=6 | 2400bps V.22bis | |--------------+---------------------------------------------| | S44=18 | 19.2Kbps V.32terbo | |--------------+---------------------------------------------| | S44=19 | 16.8Kbps V.32terbo | |--------------+---------------------------------------------| | S44=25 | 33.6Kbps AT&T V.34 | |--------------+---------------------------------------------| | S44=26 | 31.2Kbps AT&T V.34 | |--------------+---------------------------------------------| | i S44=27 | 28.8Kbps V.34 | |--------------+---------------------------------------------| | S44=28 | 26.4Kbps V.34 | |--------------+---------------------------------------------| | S44=29 | 24.0Kbps V.34 | |--------------+---------------------------------------------| | S44=30 | 21.6Kbps V.34 | |--------------+---------------------------------------------| | S44=31 | 19.2Kbps V.34 | |--------------+---------------------------------------------| | S44=32 | 16.8Kbps V.34 | |--------------+---------------------------------------------| | S44=33 | 14.4Kbps V.34 | |--------------+---------------------------------------------| | S44=34 | 12.0Kbps V.34 | |--------------+---------------------------------------------| | S44=35 | 9600bps V.34 | |--------------+---------------------------------------------| | S44=36 | 7200bps V.34 | |--------------+---------------------------------------------| | S44=37 | 4800bps V.34 | |--------------+---------------------------------------------| | S44=38 | 2400bps V.34 | +------------------------------------------------------------+ +------------------------------------------------------------+ | LEASED LINE TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S45=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S45=15 | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 15 | |--------------+---------------------------------------------| | Unit: | 1 dBm | |--------------+---------------------------------------------| | Description: | Sets the signal level for transmission when | | | in leased line mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Example: | AT &L0 H1 DT555-1212 | |--------------+---------------------------------------------| | Description: | Selects line type. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &L0 | Switched line. | |--------------+---------------------------------------------| | &L1 | 2-wire originate mode leased line. | |--------------+---------------------------------------------| | &L2 | 2-wire answer mode leased line. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S90=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S90=0 | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S90=0 | Disabled. | |--------------+---------------------------------------------| | S90=1 | Serial speed follows connect speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NETWORK POSITION IDENTIFICATION | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S74=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S74=0 &W | |--------------+---------------------------------------------| | Description: | Identifies modem as either tributary or | | | control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S74=0 | Identify as tributary | |--------------+---------------------------------------------| | iS74=1 | Identify as control | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD REMOTE ACCESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S56=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS56=6 | |--------------+---------------------------------------------| | Default: | None | |--------------+---------------------------------------------| | Range: | 00-99 | |--------------+---------------------------------------------| | Unit: | Password digits | |--------------+---------------------------------------------| | Description: | Allows entry of the first two digits of | | | remote access password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD REMOTE ACCESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S57=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS57=6 | |--------------+---------------------------------------------| | Default: | None | |--------------+---------------------------------------------| | Range: | 00-99 | |--------------+---------------------------------------------| | Unit: | Password digits | |--------------+---------------------------------------------| | Description: | Allows entry of the second two digits of | | | remote access password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD REMOTE ACCESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S58=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS58=6 | |--------------+---------------------------------------------| | Default: | None | |--------------+---------------------------------------------| | Range: | 00-99 | |--------------+---------------------------------------------| | Unit: | Password digits | |--------------+---------------------------------------------| | Description: | Allows entry of the third two digits of | | | remote access password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD REMOTE ACCESS | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S59=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS59=6 | |--------------+---------------------------------------------| | Default: | None | |--------------+---------------------------------------------| | Range: | 00-99 | |--------------+---------------------------------------------| | Unit: | Password digits | |--------------+---------------------------------------------| | Description: | Allows entry of the fourth two digits of | | | remote access password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL/SPEED | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Example: | AT %B14400 | |--------------+---------------------------------------------| | Description: | Selects the current DCE speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %B300 | Select V.21 or Bell103 at 300bps speed. | |--------------+---------------------------------------------| | %B1200 | Select V.22,V.23 or Bell 212A at 1200bps | | | speed. | |--------------+---------------------------------------------| | %B2400 | Select V.34 at 2400bps speed. | |--------------+---------------------------------------------| | %B4800 | Select V.34 at 4800bps speed. | |--------------+---------------------------------------------| | %B7200 | Select V.34 at 7200bps speed. | |--------------+---------------------------------------------| | %B9600 | Select V.34 at 9600bps uncoded speed. | |--------------+---------------------------------------------| | %B12000 | Select V.34 at 12Kbps speed. | |--------------+---------------------------------------------| | %B14400 | Select V.34 at 14.4Kbps speed. | |--------------+---------------------------------------------| | %B16800 | Select V.34 at 16.8Kbps speed. | |--------------+---------------------------------------------| | %B19200 | Select V.34 at 19.2Kbps speed. | |--------------+---------------------------------------------| | %B21600 | Select V.34 at 21.6Kbps speed. | |--------------+---------------------------------------------| | %B24000 | Select V.34 at 24Kbps speed. | |--------------+---------------------------------------------| | %B26400 | Select V.34 at 26.4Kbps speed. | |--------------+---------------------------------------------| | i %B28800 | Select V.34 at 28.8Kbps speed. | |--------------+---------------------------------------------| | %BL31200 | Select V.34 proprietary at 31.2Kbps speed. | |--------------+---------------------------------------------| | %BL33600 | Select V.34 proprietary at 33.6Kbps speed. | |--------------+---------------------------------------------| | %BL2400 | Select V.22bis at 2400Kbps speed. | |--------------+---------------------------------------------| | %BL4800 | Select V.32bis/V.32 at 4800Kbps speed. | |--------------+---------------------------------------------| | %BL7200 | Select V.32bis at 7200Kbps speed. | |--------------+---------------------------------------------| | %BL9600 | Select V.32bis/V.32 at 9600Kbps speed. | |--------------+---------------------------------------------| | %BL12000 | Select V.32bis at 12Kbps speed. | |--------------+---------------------------------------------| | %BL14400 | Select V.32bis at 14.4Kbps speed. | |--------------+---------------------------------------------| | %BL16800 | Select V.32terbo at 16.8Kbps speed. | |--------------+---------------------------------------------| | %BL19200 | Select V.32terbo at 19.2Kbps speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CLONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &&P1 [cmds] | |--------------+---------------------------------------------| | Example: | AT &&P1 &W | |--------------+---------------------------------------------| | Description: | In online command mode, copies firmware to | | | remote 3825Plus modem | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S55=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S55=0 &W | |--------------+---------------------------------------------| | Description: | Allows remote configuration by 3800 series | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S55=0 | Remote configuration enabled. | |--------------+---------------------------------------------| | S55=1 | Remote configuration disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Example: | AT I1 O | |--------------+---------------------------------------------| | Description: | Displays modem properties. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports product code. | |--------------+---------------------------------------------| | I1 | Reports firmware 3 digit version number. | |--------------+---------------------------------------------| | I2 | Performs EPROM check | |--------------+---------------------------------------------| | I3 | Reports serial number | |--------------+---------------------------------------------| | I4 | Reports model number | |--------------+---------------------------------------------| | I5 | Reports hardware part number | |--------------+---------------------------------------------| | I6 | Reports software part number | |--------------+---------------------------------------------| | I9 | Reports firmware 3 digit version number. | |--------------+---------------------------------------------| | I11 | Reports RAM checksum result. | |--------------+---------------------------------------------| | I17 | Reports last eight critical errors from | | | last to first | |--------------+---------------------------------------------| | I19 | Reports complete firmware revision number | +------------------------------------------------------------+ +------------------------------------------------------------+ | RJ11 CELLULAR ADAPT | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S93=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S93=0 &W | |--------------+---------------------------------------------| | Description: | Adds support for RJ11 connection during | | | cellular operation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S93=0 | Disabled. | |--------------+---------------------------------------------| | S93=1 | Enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY CHANGE ADMINISTRATION PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SA=nnnnnnnn [cmds] | |--------------+---------------------------------------------| | Example: | AT %SA=22233344 &W | |--------------+---------------------------------------------| | Description: | Changes administration password. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY CHANGE DTE PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SBi=nnnnnnnn [cmds] | |--------------+---------------------------------------------| | Example: | AT %SBi=22233344 &W | |--------------+---------------------------------------------| | Description: | Changes the DTE type password in index i. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY CHANGE VF PLUS DTE PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SBi=nnnnnnnn [cmds] | |--------------+---------------------------------------------| | Example: | AT %SBi=22233344 &W | |--------------+---------------------------------------------| | Description: | Changes the VF plus DTE type password in | | | index i. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY CHANGE VF PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SVi=nnnnnnnn [cmds] | |--------------+---------------------------------------------| | Example: | AT %SVi=22233344 &W | |--------------+---------------------------------------------| | Description: | Changes the VF type password in index i. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY DISPLAY PASSWORD | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %SPi [cmds] | |--------------+---------------------------------------------| | Example: | AT %SPi &W | |--------------+---------------------------------------------| | Description: | Displays the VF or DTE type password in | | | index i. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY DELETE PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SPi= [cmds] | |--------------+---------------------------------------------| | Example: | AT %SPi= &W | |--------------+---------------------------------------------| | Description: | Delete the VF or DTE type password in index | | | i. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY ENTER ADMINISTRATION PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SAnnnnnnnn [cmds] | |--------------+---------------------------------------------| | Example: | AT %SA22233344 &W | |--------------+---------------------------------------------| | Description: | Sets modem to allow security configuration | | | and password changes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SECURITY RESET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %SR [cmds] | |--------------+---------------------------------------------| | Example: | AT %SR &W | |--------------+---------------------------------------------| | Description: | Resets administration password and empties | | | password table | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORED PROFILE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S88=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S88=0 &W | |--------------+---------------------------------------------| | Description: | Loads stored profile on disconnect. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S88=0 | Disabled. | |--------------+---------------------------------------------| | S88=231 | Disabled. | |--------------+---------------------------------------------| | S88=1 | Enabled. | |--------------+---------------------------------------------| | S88=232 | Enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCHED LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS41=6 | |--------------+---------------------------------------------| | Default: | 20 | |--------------+---------------------------------------------| | Description: | Sets maximum line speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S41=1 | 14.4Kbps V.32bis | |--------------+---------------------------------------------| | S41=2 | 12.0Kbps V.32bis | |--------------+---------------------------------------------| | S41=3 | 9600bps V.32bis, V.32 | |--------------+---------------------------------------------| | S41=4 | 7200bps V.32bis | |--------------+---------------------------------------------| | S41=5 | 4800bps V.32bis, V.32 | |--------------+---------------------------------------------| | S41=6 | 2400bps V.22bis | |--------------+---------------------------------------------| | S41=7 | 1200bps V.22 | |--------------+---------------------------------------------| | S41=8 | 1200bps 212A | |--------------+---------------------------------------------| | S41=10 | 0-300bps V21 | |--------------+---------------------------------------------| | S41=11 | 0-300bps 103J | |--------------+---------------------------------------------| | S41=20 | 19.2Kbps V.32terbo | |--------------+---------------------------------------------| | S41=21 | 16.8Kbps V.32terbo | |--------------+---------------------------------------------| | S41=27 | 33.6Kbps AT&T V.34 | |--------------+---------------------------------------------| | S41=28 | 31.2Kbps AT&T V.34 | |--------------+---------------------------------------------| | i S41=29 | 28.8Kbps V.34 | |--------------+---------------------------------------------| | S41=30 | 26.4Kbps V.34 | |--------------+---------------------------------------------| | S41=31 | 24.0Kbps V.34 | |--------------+---------------------------------------------| | S41=32 | 21.6Kbps V.34 | |--------------+---------------------------------------------| | S41=33 | 19.2Kbps V.34 | |--------------+---------------------------------------------| | S41=34 | 16.8Kbps V.34 | |--------------+---------------------------------------------| | S41=35 | 14.4Kbps V.34 | |--------------+---------------------------------------------| | S41=36 | 12.0Kbps V.34 | |--------------+---------------------------------------------| | S41=37 | 9600bps V.34 | |--------------+---------------------------------------------| | S41=38 | 7200bps V.34 | |--------------+---------------------------------------------| | S41=39 | 4800bps V.34 | |--------------+---------------------------------------------| | S41=40 | 2400bps V.34 | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Configuration | |----------------+-------------------------------------------| | Format: | AT [cmds] &In [cmds] | |----------------+-------------------------------------------| | Example: | AT &I26 &W | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0-32, 99, 100 | |----------------+-------------------------------------------| | Unit: | -1 dBm | |----------------+-------------------------------------------| | Description: | Sets the signal level for transmission | |------------------------------------------------------------| | Note: 0-8 invalid in North America. Set to 99 for | | autoadjust ETC1.0 specification. Set to 100 for autoadjust | | ETC1.1 specification | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &J0 [cmds] | |--------------+---------------------------------------------| | Example: | AT &J0 &W | |--------------+---------------------------------------------| | Description: | Sets -9 dBm permissive mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.25bis CODE SET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S62=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S62=0 &W | |--------------+---------------------------------------------| | Description: | Sets coding type used in V.25bis mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S62=0 | ASCII | |--------------+---------------------------------------------| | S62=1 | EBCDIC | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.25bis IDLE CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S63=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S63=0 &W | |--------------+---------------------------------------------| | Description: | Sets V.25 idle fill type | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S63=0 | Fill character is mark. | |--------------+---------------------------------------------| | S63=1 | Fill character is flag. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.25bis NEW LINE CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S64=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S64=0 &W | |--------------+---------------------------------------------| | Description: | Sets V.25 new line character. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S64=0 | Carriage return and line feed. | |--------------+---------------------------------------------| | S64=1 | Carriage return. | |--------------+---------------------------------------------| | S64=2 | Line feed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.32bis AUTO-RETRAIN | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S76=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S76=0 &W | |--------------+---------------------------------------------| | Description: | Selects action the modem will take during | | | bad line quality on 32bis connection. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S76=0 | Auto retrain enabled. | |--------------+---------------------------------------------| | S76=1 | Auto retrain disabled. | |--------------+---------------------------------------------| | S76=2 | Auto retrain started at 4800bps for V.32bis | | | operation. | |--------------+---------------------------------------------| | S76=3 | Auto retrain started at 9600bps for V.32bis | | | operation. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.32bis TRAIN | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S43=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S43=0 &W | |--------------+---------------------------------------------| | Description: | Sets train length for V.34, V.32terbo, | | | V.32bis and V32. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S43=0 | Long | |--------------+---------------------------------------------| | S43=1 | Short | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.34 SPLIT BAUD MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S14=0 | |--------------+---------------------------------------------| | Description: | Controls V.34 split baud mode. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S14=0 | V.34 split baud mode enabled. | |--------------+---------------------------------------------| | S14=1 | V.34 split baud mode disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis COMPRESSION CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] "Hn [cmds] | |--------------+---------------------------------------------| | Example: | AT "H3 &W | |--------------+---------------------------------------------| | Description: | Controls V.42bis data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | "H0 | V.42bis disabled. | |--------------+---------------------------------------------| | "H1 | V.42bis when transmitting enabled. | |--------------+---------------------------------------------| | "H2 | V.42bis when receiving enabled. | |--------------+---------------------------------------------| | i "H3 | V.42bis when transmitting/receiving | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | XON/XOFF PASS-THROUGH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Xn [cmds] | |--------------+---------------------------------------------| | Example: | AT \X7 O | |--------------+---------------------------------------------| | Description: | Selects whether XON/XOFF signals are sent | | | to remote modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \X0 | XON/XOFF signals trapped by local modem. | |--------------+---------------------------------------------| | \X1 | XON/XOFF passed through local modem. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR ALARM | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S77=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S77=0 &W | |--------------+---------------------------------------------| | Description: | Sends alarm to proprietary Series | | | Management Controller if DTR low for 10 | | | seconds. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S77=0 | Alarm disabled. | |--------------+---------------------------------------------| | S77=1 | Alarm enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CALLBACK SECURITY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S67=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S67=0 &W | |--------------+---------------------------------------------| | Description: | Enables callback security option | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S67=0 | Disabled | |--------------+---------------------------------------------| | S67=1 | Enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | ANSWER SECURITY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S68=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S68=0 &W | |--------------+---------------------------------------------| | Description: | Selects what type of answer security is | | | used. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S68=0 | Answer security disabled | |--------------+---------------------------------------------| | S68=1 | DTE answer security enabled. | |--------------+---------------------------------------------| | S68=2 | VF and DTE answer security enabled | |--------------+---------------------------------------------| | S68=3 | VF with DTE answer security enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | ORIGINATE SECURITY | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S70=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S70=0 &W | |--------------+---------------------------------------------| | Description: | Enables originate security option | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S70=0 | Originate security disabled | |--------------+---------------------------------------------| | S70=1 | Originate security enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | VF PROMPT TYPE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S95=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S95=0 &W | |--------------+---------------------------------------------| | Description: | Selects the type of VF password prompt sent | | | to remote dialer. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S95=0 | Second dial tone | |--------------+---------------------------------------------| | S95=1 | Quiet answer | |------------------------------------------------------------| | Note: Also selects which dial modifier (@ or W) must | | precede password | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD ATTTEMPT LIMIT | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S96=n [cmds] | |--------------+---------------------------------------------| | Example: | AT S96=0 &W | |--------------+---------------------------------------------| | Description: | Sets number of DTE password attempts before | | | disconnect. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S96=0 | 1 attempt | |--------------+---------------------------------------------| | S96=1 | 2 attempts | |--------------+---------------------------------------------| | S96=2 | 3 attempts | |--------------+---------------------------------------------| | S96=3 | 4 attempts | |--------------+---------------------------------------------| | S96=4 | 5 attempts | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD DTE TERMINATION CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S97=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS97=13 | |--------------+---------------------------------------------| | Default: | 13 | |--------------+---------------------------------------------| | Range: | 1-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets Character used to indicate end of | | | password or callback directory/number | +------------------------------------------------------------+ +------------------------------------------------------------+ | PASSWORD BACKSPACE CHARACTER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S98=n [cmds] | |--------------+---------------------------------------------| | Example: | ATS98=8 | |--------------+---------------------------------------------| | Default: | 8 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets Character used backspace when entering | | | password or callback directory/number | +------------------------------------------------------------+