STOLLMANN GMBH ============== TA+ X.24/V.35 Card Type ISDN TA Chip Set Unidentified Maximum Data Rate 64Kbps x 2 Data Bus External Data Modulation Protocol V.110, 1TR6, DSS1, X.30 +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |--------+-------+----------+--------------------------------| | TXD | Red | On | TA is transmitting data | |--------+-------+----------+--------------------------------| | TXD | Red | Off | TA is not transmitting data | |--------+-------+----------+--------------------------------| | RXD | Red | On | TA is receiving data | |--------+-------+----------+--------------------------------| | RXD | Red | Off | TA is not receiving data | |--------+-------+----------+--------------------------------| | DTR | Red | On | DTR signal is high | |--------+-------+----------+--------------------------------| | DTR | Red | Off | DTR signal is low | |--------+-------+----------+--------------------------------| | DSR | Red | On | DSR signal is high | |--------+-------+----------+--------------------------------| | DSR | Red | Off | DSR signal is low | |--------+-------+----------+--------------------------------| | CTS | Red | On | CTS signal is high | |--------+-------+----------+--------------------------------| | CTS | Red | Off | CTS signal is low | |--------+-------+----------+--------------------------------| | RI | Red | Off | Phone is not ringing | |--------+-------+----------+--------------------------------| | RI | Red | Blinking | Phone is ringing | |--------+-------+----------+--------------------------------| | DCD | Red | On | Carrier signal detected | |--------+-------+----------+--------------------------------| | DCD | Red | Off | Carrier signal not detected | |---------------------------+--------------------------------| | L2 Status | L1 Status | Condition | |--------------+------------+--------------------------------| | On | On | TA is performing power-up | | | | tests or is connected | |--------------+------------+--------------------------------| | Blinking | Blinking | TA is resetting | |--------------+------------+--------------------------------| | Off | On | TA is ready | |--------------+------------+--------------------------------| | .25s on, | On | Call is in progress | | .75s off | | | |--------------+------------+--------------------------------| | .75s on, | On | Negotiation is in progress | | .25s off | | | |--------------+------------+--------------------------------| | 1s on, 1s | On | No ISDN signal detected | | off | | | |--------------+------------+--------------------------------| | .5s on, .5s | On | Remote TA busy | | off | | | |--------------+------------+--------------------------------| | .3s on, .3s | On | Remote TA did not answer | | off | | | |--------------+------------+--------------------------------| | .25s on, | On | Could not connect to remote TA | | .25s off | | | |--------------+------------+--------------------------------| | Off | Off | Hardware error detected | |--------------+------------+--------------------------------| | Blinking | Off | Hardware error detected | |--------------+------------+--------------------------------| | Off | .25s on, | ISDN has failed | | | .75s off | | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | AUTO-ANSWER TIME | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S0=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-24 | |--------------+---------------------------------------------| | Unit: | 5 seconds | |--------------+---------------------------------------------| | Description: | Sets the amount of time that will elapse | | | before the TA will answer an incoming call. | | | When this value is set to 0 the TA will not | | | automatically answer calls. A value of 1 | | | will answer immediately. Values greater | | | than 1 set the time to (n-1) * 5 seconds. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Rn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the operation of the Clear to Send | | | signal. | |------------------------------------------------------------| | Command | Function | |--------------------+---------------------------------------| | &R0 | CTS follows RTS. | |--------------------+---------------------------------------| | &R1 | CTS forced high. | |--------------------+---------------------------------------| | &R2 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | &K0 | Flow control disabled. | |------------------+-----------------------------------------| | &K3 | CTS/RTS flow control enabled. | |------------------+-----------------------------------------| | &K4 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | &K5 | Flow control disabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODES | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format: | AT [cmds] S15=n [cmds] | |--------------+---------------------------------------------| | Description: | Enables caller ID information and extended | | | result codes. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | S15=0 | Caller ID information and extended result | | | codes disabled. | |---------------+--------------------------------------------| | S15=1 | Caller ID information enabled. | |---------------+--------------------------------------------| | S15=3 | Caller ID information and extended result | | | codes enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format: | AT [cmds] S14=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0-14 | |----------------+-------------------------------------------| | Description: | Controls echo mode and result codes. | |------------------------------------------------------------| | Bit | Value | Function | |---------+---------+----------------------------------------| | 0 | 0 | Not used. | |------------------------------------------------------------| | 1 | 0 | Command echo disabled. | | | | | | | 1 | Command echo enabled. | |-------------+-------+--------------------------------------| | 2 | 0 | Result codes enabled. | | | | | | | 1 | Result codes disabled. | |-------------+-------+--------------------------------------| | 3 | 0 | Numerical result codes enabled. | | | | | | | 1 | Verbose result codes enabled. | +------------------------------------------------------------+ Proprietary Command Set +------------------------------------------------------------+ | COMMAND ECHOING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Jn | |--------------+---------------------------------------------| | Description: | Selects whether commands will be echoed | | | back to the DTE. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | J0 | Command echoing disabled. | |---------------------+--------------------------------------| | i J1 | Command echoing enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECTION SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Hn | |--------------+---------------------------------------------| | Description: | Sets the speed of the remote connection. | |------------------------------------------------------------| | Command | Function | |------------------------+-----------------------------------| | H1 | Set speed to 300bps. | |------------------------+-----------------------------------| | H2 | Set speed to 600bps. | |------------------------+-----------------------------------| | H3 | Set speed to 1200bps. | |------------------------+-----------------------------------| | H4 | Set speed to 2400bps. | |------------------------+-----------------------------------| | H5 | Set speed to 4800bps. | |------------------------+-----------------------------------| | i H6 | Set speed to 9600bps. | |------------------------+-----------------------------------| | H7 | Set speed to 19.2Kbps. | |------------------------+-----------------------------------| | H8 | Set speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CHANGE PROFILE CHANNEL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PROn | |--------------+---------------------------------------------| | Description: | Selects which channel's profile is being | | | edited. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | PRO1 | Edit profile for channel 1. | |---------------------+--------------------------------------| | PRO2 | Edit profile for channel 2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NCTS 0x01 | CTS is forced low. | |---------------+--------------------------------------------| | NCTS 0x02 | CTS is forced high. | |---------------+--------------------------------------------| | NCTS 0x04 | CTS follows DTR. | |---------------+--------------------------------------------| | NCTS 0x08 | CTS follows RTS. | |---------------+--------------------------------------------| | NCTS 0x10 | CTS is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NCTS 0x20 | CTS follows remote DTR. | |---------------+--------------------------------------------| | NCTS 0x40 | CTS follows remote RTS. | |---------------+--------------------------------------------| | NCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WCTS 0x01 | CTS is forced low. | |----------------+-------------------------------------------| | WCTS 0x02 | CTS is forced high. | |----------------+-------------------------------------------| | WCTS 0x04 | CTS follows DTR. | |----------------+-------------------------------------------| | WCTS 0x08 | CTS follows RTS. | |----------------+-------------------------------------------| | WCTS 0x10 | CTS is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WCTS 0x20 | CTS follows remote DTR. | |----------------+-------------------------------------------| | WCTS 0x40 | CTS follows remote RTS. | |----------------+-------------------------------------------| | WCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | CTS SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CCTS 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the CTS signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CCTS 0x01 | CTS is forced low. | |---------------+--------------------------------------------| | CCTS 0x02 | CTS is forced high. | |---------------+--------------------------------------------| | CCTS 0x04 | CTS follows DTR. | |---------------+--------------------------------------------| | CCTS 0x08 | CTS follows RTS. | |---------------+--------------------------------------------| | CCTS 0x10 | CTS is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CCTS 0x20 | CTS follows remote DTR. | |---------------+--------------------------------------------| | CCTS 0x40 | CTS follows remote RTS. | |---------------+--------------------------------------------| | CCTS 0x80 | CTS follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA LENGTH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Ln | |--------------+---------------------------------------------| | Description: | Selects how many data bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |--------------------------+---------------------------------| | i L0 | Synchronous mode. | |--------------------------+---------------------------------| | L7 | 7 data bits. | |--------------------------+---------------------------------| | L8 | 8 data bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA PARITY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Mn | |--------------+---------------------------------------------| | Description: | Selects how many parity bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |----------------------------+-------------------------------| | i M0 | No parity. | |----------------------------+-------------------------------| | M1 | Odd parity. | |----------------------------+-------------------------------| | M2 | Even parity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA STOP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Nn | |--------------+---------------------------------------------| | Description: | Selects how many stop bits will be | | | transmitted. | |------------------------------------------------------------| | Command | Function | |-----------------------------+------------------------------| | i M1 | 1 stop bit. | |-----------------------------+------------------------------| | M2 | 2 stop bits. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NDCD 0x01 | DCD is forced low. | |---------------+--------------------------------------------| | NDCD 0x02 | DCD is forced high. | |---------------+--------------------------------------------| | NDCD 0x04 | DCD follows DTR. | |---------------+--------------------------------------------| | NDCD 0x08 | DCD follows RTS. | |---------------+--------------------------------------------| | NDCD 0x10 | DCD is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NDCD 0x20 | DCD follows remote DTR. | |---------------+--------------------------------------------| | NDCD 0x40 | DCD follows remote RTS. | |---------------+--------------------------------------------| | NDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WDCD 0x01 | DCD is forced low. | |----------------+-------------------------------------------| | WDCD 0x02 | DCD is forced high. | |----------------+-------------------------------------------| | WDCD 0x04 | DCD follows DTR. | |----------------+-------------------------------------------| | WDCD 0x08 | DCD follows RTS. | |----------------+-------------------------------------------| | WDCD 0x10 | DCD is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WDCD 0x20 | DCD follows remote DTR. | |----------------+-------------------------------------------| | WDCD 0x40 | DCD follows remote RTS. | |----------------+-------------------------------------------| | WDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCD SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CDCD 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DCD signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CDCD 0x01 | DCD is forced low. | |---------------+--------------------------------------------| | CDCD 0x02 | DCD is forced high. | |---------------+--------------------------------------------| | CDCD 0x04 | DCD follows DTR. | |---------------+--------------------------------------------| | CDCD 0x08 | DCD follows RTS. | |---------------+--------------------------------------------| | CDCD 0x10 | DCD is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CDCD 0x20 | DCD follows remote DTR. | |---------------+--------------------------------------------| | CDCD 0x40 | DCD follows remote RTS. | |---------------+--------------------------------------------| | CDCD 0x80 | DCD follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DEBUG PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | TEST | |--------------+---------------------------------------------| | Description: | Displays the profile editor debug page. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | En | |--------------+---------------------------------------------| | Description: | Selects the dial mode the TA will use. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i E1 | Manual dialing only; prompt for number | | | will be displayed. | |---------------+--------------------------------------------| | E2 | Asynchronous V.25bis dial mode. | |---------------+--------------------------------------------| | E3 | Hotline dial mode; DTR is used for call | | | signalling. | |---------------+--------------------------------------------| | E4 | Hotline dial mode; RTS is used for call | | | signalling. | |---------------+--------------------------------------------| | E5 | Hotline dial mode; automatic dial attempt. | |---------------+--------------------------------------------| | E6 | Incoming calls only. | |---------------+--------------------------------------------| | E7 | Hayes dialing mode. | |---------------+--------------------------------------------| | E8 | Synchronous V.25bis dial mode. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - NO CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | NDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | when there is no ISDN connection. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | NDSR 0x01 | DSR is forced low. | |---------------+--------------------------------------------| | NDSR 0x02 | DSR is forced high. | |---------------+--------------------------------------------| | NDSR 0x04 | DSR follows DTR. | |---------------+--------------------------------------------| | NDSR 0x08 | DSR follows RTS. | |---------------+--------------------------------------------| | NDSR 0x10 | DSR is forced high during connection and | | | negotiation only. | |---------------+--------------------------------------------| | NDSR 0x20 | DSR follows remote DTR. | |---------------+--------------------------------------------| | NDSR 0x40 | DSR follows remote RTS. | |---------------+--------------------------------------------| | NDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - NEGOTIATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | WDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | while dialing and negotiating a connection. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | WDSR 0x01 | DSR is forced low. | |----------------+-------------------------------------------| | WDSR 0x02 | DSR is forced high. | |----------------+-------------------------------------------| | WDSR 0x04 | DSR follows DTR. | |----------------+-------------------------------------------| | WDSR 0x08 | DSR follows RTS. | |----------------+-------------------------------------------| | WDSR 0x10 | DSR is forced high during connection and | | | synchronization only. | |----------------+-------------------------------------------| | WDSR 0x20 | DSR follows remote DTR. | |----------------+-------------------------------------------| | WDSR 0x40 | DSR follows remote RTS. | |----------------+-------------------------------------------| | WDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DSR SIGNAL - CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | CDSR 0xhh | |--------------+---------------------------------------------| | Description: | Controls the behaviour of the DSR signal | | | while connected. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | CDSR 0x01 | DSR is forced low. | |---------------+--------------------------------------------| | CDSR 0x02 | DSR is forced high. | |---------------+--------------------------------------------| | CDSR 0x04 | DSR follows DTR. | |---------------+--------------------------------------------| | CDSR 0x08 | DSR follows RTS. | |---------------+--------------------------------------------| | CDSR 0x10 | DSR is forced high during connection and | | | synchronization only. | |---------------+--------------------------------------------| | CDSR 0x20 | DSR follows remote DTR. | |---------------+--------------------------------------------| | CDSR 0x40 | DSR follows remote RTS. | |---------------+--------------------------------------------| | CDSR 0x80 | DSR follows V.110 flow control. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTE/DCE MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Sn | |--------------+---------------------------------------------| | Description: | Sets whether the TA will operate as a DTE | | | or a DCE device. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | i S0 | TA will operate as DCE. | |-----------------------+------------------------------------| | S1 | TA will operate as DTE. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR SIGNAL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Dn | |--------------+---------------------------------------------| | Description: | Controls the operation of the Data Terminal | | | Ready signal. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | D0 | Incoming calls accepted regardless of DTR | | | state; low DTR does not disconnect. | |----------------+-------------------------------------------| | i D1 | Incoming calls accepted only if DTR is | | | high; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR disconnects. | |----------------+-------------------------------------------| | D2 | Incoming calls accepted only if DTR is | | | high; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | disconnects. | |----------------+-------------------------------------------| | D3 | Incoming calls accepted regardless of DTR | | | state; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR disconnects. | |----------------+-------------------------------------------| | D4 | Incoming calls accepted regardless of DTR | | | state; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | disconnects. | |----------------+-------------------------------------------| | D5 | Incoming calls accepted only if DTR is | | | high; DTR or RTS transition to high will | | | initiate a hotline call if in hotline | | | mode; low DTR does not disconnect. | |----------------+-------------------------------------------| | D6 | Incoming calls accepted only if DTR is | | | high; high DTR or RTS will initiate a | | | hotline call if in hotline mode; low DTR | | | does not disconnect. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EAZ | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | An | |--------------+---------------------------------------------| | Description: | Sets which incoming calls are answered. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | A0 | All incoming calls are answered; all | | | channels are notified of the call. | |---------------+--------------------------------------------| | A1 - A8 | Only calls with a matching EAZ are | | | answered. | |---------------+--------------------------------------------| | A9 | All incoming calls are answered; only the | | | channel matching the EAZ is notified of | | | the call. | +------------------------------------------------------------+ +------------------------------------------------------------+ | EAZ - EDITOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Tn | |--------------+---------------------------------------------| | Description: | Sets which incoming calls should be routed | | | for remote configuration. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | T0 | Only calls ending in "e" are routed to | | | the editor. | |----------------+-------------------------------------------| | T1 - T8 | Only calls with a matching EAZ are | | | answered. | |----------------+-------------------------------------------| | T9 | Calls matching the EAZ or ending in "e" | | | are routed to the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | ENTER PROFILE EDITOR | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Description: | Enters the profile editor so that changes | | | may be made. | |------------------------------------------------------------| | Mode | Command | |---------------+--------------------------------------------| | Manual dial | | |---------------+--------------------------------------------| | V.25bis dial | | |---------------+--------------------------------------------| | Hayes dial | AT | |---------------+--------------------------------------------| | All other | Push reset button, then | | modes | | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXIT PROFILE EDITOR | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | EXIT | | | | | | | |--------------+---------------------------------------------| | Description: | Quits the editor without saving changes. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE - DCE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Bn | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | B0 | Flow control disabled. | |------------------+-----------------------------------------| | i B1 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | B2 | CTS flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL MODE - DTE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Cn | |--------------+---------------------------------------------| | Description: | Sets the type of flow control used. | |------------------------------------------------------------| | Command | Function | |------------------+-----------------------------------------| | C0 | Flow control disabled. | |------------------+-----------------------------------------| | i C1 | XON/XOFF flow control enabled. | |------------------+-----------------------------------------| | C2 | RTS flow control enabled. | |------------------+-----------------------------------------| | C3 | DTR flow control enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOTLINE NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | HOT <#> | |--------------+---------------------------------------------| | Description: | Sets the number for hotline calling. If no | | | number is given, hotline calling will not | | | be allowed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Fn | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 60 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the amount of time that there must be | | | no activity on the ISDN line before the TA | | | disconnects. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INCOMING CALL NUMBER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | RUFn <#> | |--------------+---------------------------------------------| | Description: | Sets the number in position n of allowed | | | incoming calls. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LANGUAGE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Kn | |--------------+---------------------------------------------| | Description: | Selects the language the TA will display | | | messages in. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | K0 | Messages will be displayed in English. | |---------------+--------------------------------------------| | i K1 | Messages will be displayed in German. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Rn | |--------------+---------------------------------------------| | Description: | Sets the type of line the TA will be | | | operating on. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i R0 | ISDN with BRI service. | |---------------+--------------------------------------------| | R1 | Group 3 leased line service with 1TR6. | |---------------+--------------------------------------------| | R2 | Group 2 leased line, 2B+D or B+D. | |---------------+--------------------------------------------| | R3 | Group 0 leased line, single B channel | | | only. | |---------------+--------------------------------------------| | R4 | Point-to-point switched line. | |---------------+--------------------------------------------| | R5 | Point-to-point group 3 leased line with | | | 1TR6. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - INCOMING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Pn | |--------------+---------------------------------------------| | Description: | Sets the use of LLC for incoming DSS1 | | | calls. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | P1 | Only calls with matching LLC will be | | | answered. | |---------------+--------------------------------------------| | i P2 | Ignore LLC when answering calls. | |---------------+--------------------------------------------| | P3 | All data calls will be answered. | |---------------+--------------------------------------------| | P4 | All calls will be answered. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - OUTGOING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | On | |--------------+---------------------------------------------| | Description: | Sets the use of LLC for outgoing DSS1 | | | calls. | |------------------------------------------------------------| | Command | Function | |-----------------------+------------------------------------| | O1 | Standard LLC enabled. | |-----------------------+------------------------------------| | i O2 | LLC disabled. | |-----------------------+------------------------------------| | O3 | User-defined LLC enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LLC - USER-DEFINED DATA OCTET | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | LLC=hh hh hh.. | |--------------+---------------------------------------------| | Description: | Sets the user-defined LLC octets in | | | hexadecimal. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOAD FIRMWARE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | LOAD | |--------------+---------------------------------------------| | Description: | Begins an XMODEM transfer to receive a | | | firmware update. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCAL SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Gn | |--------------+---------------------------------------------| | Description: | Sets the speed of the serial port. | |------------------------------------------------------------| | Command | Function | |---------------------+--------------------------------------| | G1 | Set speed to 300bps. | |---------------------+--------------------------------------| | G2 | Set speed to 600bps. | |---------------------+--------------------------------------| | G3 | Set speed to 1200bps. | |---------------------+--------------------------------------| | G4 | Set speed to 2400bps. | |---------------------+--------------------------------------| | G5 | Set speed to 4800bps. | |---------------------+--------------------------------------| | i G6 | Set speed to 9600bps. | |---------------------+--------------------------------------| | G7 | Set speed to 19.2Kbps. | |---------------------+--------------------------------------| | G8 | Set speed to 38.4Kbps. | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | In | |--------------+---------------------------------------------| | Description: | Selects whether the serial port speed will | | | be adjusted to the DTE speed. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | I0 | Serial port speed locked. | |----------------+-------------------------------------------| | i I1 | Serial port speed will match DTE speed. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MALL <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for the TA and | | | the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - TA | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MTA1 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for the TA. | +------------------------------------------------------------+ +------------------------------------------------------------+ | MSN - EDITOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | MED1 <#>*n | |--------------+---------------------------------------------| | Description: | Sets the MSN and subaddress for the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | NEXT PAGE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | NEXT | |--------------+---------------------------------------------| | Description: | Shows the next page of values. | +------------------------------------------------------------+ +------------------------------------------------------------+ | PREVIOUS PAGE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | PREV | |--------------+---------------------------------------------| | Description: | Shows the previous page of values. | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE CONFIGURATION PASSWORD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | PWD xxxx | |--------------+---------------------------------------------| | Description: | Sets the password for remote configuration. | | | If no password is given, no password will | | | be required. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TA | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | FRES | |--------------+---------------------------------------------| | Description: | Resets the TA to its power-on state. | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESET TO FACTORY DEFAULTS | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | DEFA | |--------------+---------------------------------------------| | Description: | Resets all settings to their factory | | | defaults. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SAVE PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | SAVE | |--------------+---------------------------------------------| | Description: | Saves the current settings into the profile | | | and quits the editor. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERVICE INDICATOR | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Pn | |--------------+---------------------------------------------| | Description: | Sets the 1TR6 Service Indicator. | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | i P0 | Service Indicator reports standard line. | |----------------+-------------------------------------------| | P1 | Service Indicator reports Private SI. | |----------------+-------------------------------------------| | P2 | Service Indicator reports Private 2. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERVICE INDICATOR DETAILS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | On | |--------------+---------------------------------------------| | Description: | Sets the details for the 1TR6 Service | | | Indicator. | |------------------------------------------------------------| | Pn Setting | Command | Function | |---------------+---------+----------------------------------| | P0 | i O1 | Service Indicator reports 1TR6. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports X.21. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports AOI | | | | synch/asynch mode. | |---------------+---------+----------------------------------| | P1 | i O1 | Service Indicator reports V.24 | | | | asynch. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports 64Kbps | | | | asynch. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports V.24 | | | | BTX. | |---------------+---------+----------------------------------| | | O4 | Service Indicator reports V.24 | | | | Text. | |---------------+---------+----------------------------------| | | O5 | Service Indicator reports 64Kbps | | | | PC-Net. | |---------------+---------+----------------------------------| | P2 | i O1 | Service Indicator reports | | | | Private 2 LLC with the data | | | | octet equal to 0. | |---------------+---------+----------------------------------| | | O2 | Service Indicator reports | | | | Private 2 LLC with the data | | | | octet not equal to 0. | |---------------+---------+----------------------------------| | | O3 | Service Indicator reports | | | | Private 2 with the data octet | | | | equal to 0. | +------------------------------------------------------------+ +------------------------------------------------------------+ | SYNCHRONOUS SPEED | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | Qn | |--------------+---------------------------------------------| | Description: | Selects what data rate the TA will operate | | | in when in synchronous mode. | |------------------------------------------------------------| | Command | Function | |-------------------+----------------------------------------| | Q0 | Use V.24 asynchronous mode. | |-------------------+----------------------------------------| | Q1 | Use data rate set with Gn and Hn. | |-------------------+----------------------------------------| | i Q2 | Use 64Kbps data rate. | |-------------------+----------------------------------------| | Q3 | Use 56Kbps data rate. | |-------------------+----------------------------------------| | Q4 | Use 48Kbps data rate. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UPDATE PROFILE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | UPDA | |--------------+---------------------------------------------| | Description: | Saves the current settings into the | | | profile. | +------------------------------------------------------------+