SOUTH MOUNTAIN TELECOMMUNICATIONS ================================= SM-5743 Card Type Fax, Modem (asynchronous) Chip Set Unidentified Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus 8-bit ISA Fax Class Class I & II Data Modulation Bell 103A/212A Protocol ITU-T V.21,V.22, V.22bis, V.32, V.32bis Fax Modulation ITU-T V.17, V.21 ch2, V.27ter, V.29 Protocol Error MNP2-5, V.42, V.42bis Correction/Compression Boot ROM Not available +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Line out | CN2 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL PORT ADDRESS | |------------------------------------------------------------| | Setting | SW1/1 | SW1/2 | |--------------------+-------------------+-------------------| | i COM1 (3F8h) | On | On | |--------------------+-------------------+-------------------| | COM2 (2F8h) | Off | On | |--------------------+-------------------+-------------------| | COM3 (3E8h) | On | Off | |--------------------+-------------------+-------------------| | COM4 (2E8h) | Off | Off | +------------------------------------------------------------+ +------------------------------------------------------------+ | INTERRUPT | |------------------------------------------------------------| | Setting | SW1/3 | SW1/4 | |--------------------+-------------------+-------------------| | 2 | On | Off | |--------------------+-------------------+-------------------| | 3 | Off | On | |--------------------+-------------------+-------------------| | i 4 | On | On | |--------------------+-------------------+-------------------| | 5 | Off | Off | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | SUPPORTED STANDARD COMMANDS | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | +++, 'comma', A/ | |------------------------------------------------------------| | A, D, H, L, M, N, O, Q, V, W, X, Z | |------------------------------------------------------------| | &D, &F, &G, &J, &K, &V, &W, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \G, \K, \V, \X, %A, %C, %E, %L, %Q | |------------------------------------------------------------| | S-Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S18, S25, S26, S46, S48 | |------------------------------------------------------------| | Note: See MHI documentation for complete information. | +------------------------------------------------------------+ +------------------------------------------------------------+ | UNIDENTIFIED COMMANDS | |------------------------------------------------------------| | Command | Default | |------------------------------+-----------------------------| | S37 | 0 | |------------------------------+-----------------------------| | S42 | 0 | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 1200bps | |--------------+---------------------------------------------| | i B1 | Bell 212A at 1200bps | |--------------+---------------------------------------------| | B2 | V.23- originate mode receive at 1200bps, | | | send at 75bps; answer mode receive at | | | 75bps, send at 1200bps | |--------------+---------------------------------------------| | B3 | V.23- originate mode receive at 75bps, send | | | at 1200bps; answer mode receive at 1200bps, | | | send at 75bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |------------------------------------------------------------| | Command | Function | |----------------------+-------------------------------------| | \N0 | Normal mode enabled | |----------------------+-------------------------------------| | \N1 | Direct mode enabled | |----------------------+-------------------------------------| | \N2 | MNP reliable mode enabled | |----------------------+-------------------------------------| | i\N4 | Auto-reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISPLAY INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested about the | | | modem. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Displays product identification code. | |--------------+---------------------------------------------| | I1 | Displays ROM checksum. | |--------------+---------------------------------------------| | I3 | Displays firmware revision. | |--------------+---------------------------------------------| | I4 | Displays product features. | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S30=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Maximum duration of DTE and DCE inactivity | | | allowed prior to initiating hang-up | | | process. | |--------------+---------------------------------------------| | Note: | S30=0 disables the timer and allows | | | indefinite inactivity. | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.32 - AUTO-RETRAIN | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Bn [cmds] | |--------------+---------------------------------------------| | Description: | Controls auto-retrain function if poor line | | | quality is detected | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &B0 | Auto-retrain disabled modem hangs-up | |--------------+---------------------------------------------| | i &B1 | Auto-retrain enabled if line quality is | | | poor | |--------------+---------------------------------------------| | &B2 | No hang-up, no auto-retrain | +------------------------------------------------------------+