SHARK MULTIMEDIA ================ LEOPARD 56K Card Type Modem (asynchronous) Chip Set Rockwell I/O Options Line in, line out, microphone in, speaker out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103/212A Protocol ITU-T V.34, V.FC, V.32bis, V.32, V.22bis, V.22, V.23, V.21 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29, Protocol Unidentified Error MNP5, V.42bis Correction/Compression Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, half-height card +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line out | CN1 | Microphone | CN3 | |----------------------------+----------+-------------+------| | Line in | CN2 | Speaker out | CN4 | +------------------------------------------------------------+ +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |------------------------------------------------------------| | &D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \A, \B, \K, \N, | |------------------------------------------------------------| | %C, %E, %L, %Q | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, | | S14, S16, S18, S21, S22, S23, S24, S25, S26, | |------------------------------------------------------------| | S27, S28, S29, S30, S38, S39, S40, S46, S48, S82, S91, | | S92, S95 | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | -K, +MS | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | TRANSMIT CARRIER | |------------------------------------------------------------| | Type: | Configuration | |---------------+--------------------------------------------| | Format: | AT [cmds] Cn [cmds] | |---------------+--------------------------------------------| | Description: | Controls the transmit carrier switching | |------------------------------------------------------------| | Note: Disabling the transmit carrier puts the modem | | in receive-only mode | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | i C1 | Return OK message | +------------------------------------------------------------+ +------------------------------------------------------------+ | ECHOPLEX | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Fn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether commands sent while in data | | | mode are echoed | |------------------------------------------------------------| | Note: This command is only supported on older modems | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | F0 | Auto detect mode | |--------------+---------------------------------------------| | i F1 | V.21 or Bell 103 | |--------------+---------------------------------------------| | F3 | V.23 line modulation | |--------------+---------------------------------------------| | F4 | V.22 or Bell 212A 1200bps line speed | |--------------+---------------------------------------------| | F5 | V.22bis line modulation | |--------------+---------------------------------------------| | F6 | V.32bis or V.32 4800 line modulation | |--------------+---------------------------------------------| | F7 | V.32bis 7200 line modulation | |--------------+---------------------------------------------| | F8 | V.32bis or V.32 9600 line modulation | |--------------+---------------------------------------------| | F9 | V.32bis 12000 line modulation | |--------------+---------------------------------------------| | F10 | V.32bis 14400 line modulation | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] In [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports modem model and speed | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Report OK | |--------------+---------------------------------------------| | I3 | Report firmware revision, model, and | | | interface type | |--------------+---------------------------------------------| | I4 | Report response programmed by OEM | |--------------+---------------------------------------------| | I5 | Report the country code parameter | |--------------+---------------------------------------------| | I6 | Report modem data pump model and code | | | revision | |--------------+---------------------------------------------| | I7 | Report DAA code | +------------------------------------------------------------+ +------------------------------------------------------------+ | SPEAKER VOLUME | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Ln [cmds] | |--------------+---------------------------------------------| | Description: | Controls speaker volume | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | L0 | Low volume setting | |--------------+---------------------------------------------| | L1 | Low volume setting | |--------------+---------------------------------------------| | L2 | Medium volume setting | |--------------+---------------------------------------------| | L3 | Highest volume setting | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | i N1 | Auto-mode detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | RLSD | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the RLSD option is enabled | | | or disabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &C0 | Force RLSD active regardless of the carrier | | | state | |--------------+---------------------------------------------| | &C1 | Allow RLSD to follow the carrier state | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &F [cmds] | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &F0 | Restore factory configuration 0 | |--------------+---------------------------------------------| | &F1 | Restore factory configuration 1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | GUARD TONE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Gn [cmds] | |--------------+---------------------------------------------| | Description: | Commands the modem to transmit a guard tone | | | in V.22/V.22bis | |------------------------------------------------------------| | Note: Used primarily for international data | | transmission | |------------------------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &G0 | Guard tone disabled | |--------------+---------------------------------------------| | &G1 | Guard tone disabled | |--------------+---------------------------------------------| | &G2 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | JACK TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Jn [cmds] | |--------------+---------------------------------------------| | Description: | Included for compatibility, performs no | | | function. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K5 | Transparent XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K6 | RTS/CTS and XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | LINE TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects line type | |--------------+---------------------------------------------| | Command | Line Type | |--------------+---------------------------------------------| | &L0 | Switched line (PSTN/Dial-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &V [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &V1 | Displays the connection statistics | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | CONNECT MESSAGE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects extended result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \V0 | Connect messages are controlled by the | | | command settings X, W, and S95 | |--------------+---------------------------------------------| | \V1 | Connect messages are displayed in the | | | single line format | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %An [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used as the | | | auto-reliable fallback character | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %A0 | Disable | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG AND PLAY SERIAL NUMBER | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %7 [cmds] | |--------------+---------------------------------------------| | Description: | Displays the Plug and Play serial number | +------------------------------------------------------------+ +------------------------------------------------------------+ | PLUG AND PLAY VENDOR ID | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] %8 [cmds] | |--------------+---------------------------------------------| | Description: | Displays the Plug and Play vendor ID and | | | product number | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP10 - FALLBACK | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SECn [cmds] | |--------------+---------------------------------------------| | Description: | Allows MNP10 to fall back to speeds slower | | | than 4800bps | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SEC0 | MNP 10-EC disabled | |--------------+---------------------------------------------| | -SEC1 | MNP 10-EC enabled and set transmit level | | | 0 to 30 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DISTINCTIVE RING | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -SDR=n [cmds] | |--------------+---------------------------------------------| | Description: | Controls the distinctive ring type | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -SDR=0 | Disable distinctive ring | |--------------+---------------------------------------------| | -SDR=1 | Ring type 1 | |--------------+---------------------------------------------| | -SDR=2 | Ring type 2 | |--------------+---------------------------------------------| | -SDR=3 | Ring type 1 and 2 | |--------------+---------------------------------------------| | -SDR=4 | Ring type 3 | |--------------+---------------------------------------------| | -SDR=5 | Ring type 1 and 3 | |--------------+---------------------------------------------| | -SDR=6 | Ring type 2 and 3 | |--------------+---------------------------------------------| | -SDR=7 | Ring type 1, 2, and 3 | +------------------------------------------------------------+ +------------------------------------------------------------+ | RPI MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] +H [cmds] | |--------------+---------------------------------------------| | Description: | Sets the flash memory download speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | +H0 | RPI/Video Ready Mode disabled | |--------------+---------------------------------------------| | +H1 | RPI enabled and DTE speed set to 19200kps | |--------------+---------------------------------------------| | +H2 | RPI enabled and DTE speed set to 38400kps | |--------------+---------------------------------------------| | +H3 | RPI enabled and DTE speed set to 57600kps | |--------------+---------------------------------------------| | +H11 | RPI+ mode enabled | |--------------+---------------------------------------------| | +H16 | Video Ready Mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BLACKLISTED NUMBERS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *B [cmds] | |--------------+---------------------------------------------| | Description: | Displays the list of permanently | | | blacklisted numbers | +------------------------------------------------------------+ +------------------------------------------------------------+ | DELAYED NUMBERS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *D [cmds] | |--------------+---------------------------------------------| | Description: | Displays the list of delayed numbers | +------------------------------------------------------------+ +------------------------------------------------------------+ | COUNTRY | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] *NCn [cmds] | |--------------+---------------------------------------------| | Description: | Changes the country to one of eight listed | | | in NVRAM | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | BIT-MAPPED REGISTER S19 | |------------------------------------------------------------| | Format | AT [cmds] S19=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | Unidentified | |--------------+---------------------------------------------| | Description: | AutoSync options | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S20 | |------------------------------------------------------------| | Format | AT [cmds] S20=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | AutoSync HDLC address or BSC Sync character | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S31 | |------------------------------------------------------------| | Format: | AT [cmds] S31=n [cmds] | |----------------+-------------------------------------------| | Default: | Unidentified | |----------------+-------------------------------------------| | Range: | 0-10 | |----------------+-------------------------------------------| | Description: | Select automode and extended result code | | | format. | |------------------------------------------------------------| | Bit | Value | Function | |----------+-------+-----------------------------------------| | 0 | 0 | Not used | |----------+-------+-----------------------------------------| | 1 | 0 | Auto-mode detection disabled | | | | | | | 1 | In originate mode, handshake begins at | | | | line speed designated by the S37 | | | | register. Modem can shift to a slower | | | | speed if necessary. | | | | | | | | In answer mode, handshake attempted | | | | with the following protocols in order - | | | | V.FC, V.32bis, V.32, V.22bis, V.22 or | | | | Bell 212, V.21, and Bell 103 | |----------+-------+-----------------------------------------| | 2-3 | 0 | Auto line speed detection (Nn) disabled | | | | | | | 1 | Auto line speed detection (Nn) enabled | |----------+-------+-----------------------------------------| | 4-5 | 0 | Caller ID disabled | | | | | | | 1 | Short Caller ID enabled | | | | | | | 2 | Long Caller ID enabled | |----------+-------+-----------------------------------------| | 6-7 | 11b | Reserved | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S37=0 | Attempt automode connection. If N0 is | | | active, connection is attempted at the most | | | recently sensed DTE speed. If N1 is active, | | | connection is attempted at the highest | | | possible speed. | |--------------+---------------------------------------------| | S37=1-3 | Attempt to connect at 300bps | |--------------+---------------------------------------------| | S37=4 | Reserved | |--------------+---------------------------------------------| | S37=5 | Attempt to connect at 1200bps | |--------------+---------------------------------------------| | S37=6 | Attempt to connect at 2400bps | |--------------+---------------------------------------------| | S37=7 | Attempt to connect at V.23 | |--------------+---------------------------------------------| | S37=8 | Attempt to connect at 4800bps | |--------------+---------------------------------------------| | S37=9 | Attempt to connect at 9600bps | |--------------+---------------------------------------------| | S37=10 | Attempt to connect at 12000bps | |--------------+---------------------------------------------| | S37=11 | Attempt to connect at 14400bps | |--------------+---------------------------------------------| | S37=12 | Attempt to connect at 7200bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S41 | |------------------------------------------------------------| | Format | AT [cmds] S41=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-31 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects compression, auto-retrain, flow | | | control, and MNP mode. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0-1 | 0 | Disabled | | | | | | | 1 | MNP5 | | | | | | | 2 | V.42bis | | | | | | | 3 | MNP5 and V.42bis | |------+-------+---------------------------------------------| | 2,6 | 0,0 | Retrain and fallback/fall forward disabled | | | | | | | 0,1 | Retrain enabled | | | | | | | 1,0 | Fallback/fall forward enabled | |------+-------+---------------------------------------------| | 3 | | Reserved | |------+-------+---------------------------------------------| | 4-5 | | Reserved | |------+-------+---------------------------------------------| | 7 | | Reserved | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S86 | |------------------------------------------------------------| | Format | AT [cmds] S86=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0, 4, 5, 9, 12, 13, 14 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Records the first event that contributes to | | | a NO CARRIER message. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S86=0 | Normal disconnect, no error occurred | |--------------+---------------------------------------------| | S86=4 | Loss of carrier | |--------------+---------------------------------------------| | S86=5 | V.42 negotiation failed to detect an | | | error-correction modem at the other end | |--------------+---------------------------------------------| | S86=9 | The modems could not find a common protocol | |--------------+---------------------------------------------| | S86=12 | Normal disconnect initiated by the remote | | | modem | |--------------+---------------------------------------------| | S86=13 | Remote modem does not respond after 10 | | | re-transmissions of the same message | |--------------+---------------------------------------------| | S86=14 | Protocol violation | +------------------------------------------------------------+