TRENDWARE INTERNATIONAL ======================= TEM-336P PCMCIA Card Type Modem, Fax Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A Protocol ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Protocol Error MNP5, V.42, V.42bis Correction/Compression Fax Class Class I Data Bus PCMCIA 54927 +------------------------------------------------------------+ | SUPPORTED COMMAND SET | |------------------------------------------------------------| | Basic AT Commands | |------------------------------------------------------------| | AT, A/ | |------------------------------------------------------------| | A, E, H, M, P, Q, T, V, W | |------------------------------------------------------------| | &C, &F, &G, &V, &Z | |------------------------------------------------------------| | Extended AT Commands | |------------------------------------------------------------| | \J, \T, \V | |------------------------------------------------------------| | Special Commands | |------------------------------------------------------------| | -C | |------------------------------------------------------------| | S Registers | |------------------------------------------------------------| | S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S30 | |------------------------------------------------------------| | Note: See MHI Help File for full command documentation. | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | COMMUNICATION PROTOCOLS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Bn [cmds] | |--------------+---------------------------------------------| | Description: | Selects the communication protocol for data | | | calls | |------------------------------------------------------------| | Note: The B command allows the simultaneous selection | | of more than one suffix, enabling multiple protocols. | |------------------------------------------------------------| | Command | Protocol | |--------------+---------------------------------------------| | B0 | ITU-T V.22 at 1200bps | |--------------+---------------------------------------------| | B1 | Bell 212A at 1200bps | |--------------+---------------------------------------------| | B2 | V.23 at 1200/75bps | |--------------+---------------------------------------------| | B3 | V.23 at 75/1200bps | |--------------+---------------------------------------------| | B15 | V.21 at 300bps | |--------------+---------------------------------------------| | B16 | Bell 103 at 300bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | |--------------+---------------------------------------------| | Note: | Any combination of modifiers can be used to | | | produce the desired dial functions in | | | sequence. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | DL | Re-dial last number | |--------------+---------------------------------------------| | DP | Pulse dialing enabled | |--------------+---------------------------------------------| | DR | Answer mode enabled; originate mode | | | disabled following handshake initiation. | |--------------+---------------------------------------------| | DS=n | Dial stored telephone number n | |--------------+---------------------------------------------| | DT | Tone dialing enabled/Pulse dialing disabled | |--------------+---------------------------------------------| | DW | Dialing resumed following dial tone | | | detection | |--------------+---------------------------------------------| | D, | Dialing paused for amount of time specified | | | in S8 register | |--------------+---------------------------------------------| | D! | Flash function initiated. Modem commanded | | | to go off-hook for specified time before | | | returning on-hook. | |--------------+---------------------------------------------| | D@ | Wait for Quite Answer function enabled. | | | Modem waits until a "quiet answer," a | | | ring-back signal followed by silence up to | | | the time specified in S7, is received prior | | | to executing the rest of the dial string. | |--------------+---------------------------------------------| | D; | Modem returned to idle state after dialing. | | | The semicolon can only be placed at the end | | | of the dial command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-MODE DETECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Nn [cmds] | |--------------+---------------------------------------------| | Description: | Selects various options for the automatic | | | detection and negotiation of protocols | | | during the handshake process if the modem | | | is communicating with a remote modem of | | | dissimilar speed. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | N0 | Auto-mode detection disabled | |--------------+---------------------------------------------| | i N1 | In originate mode, handshake begins at line | | | speed designated by the S37 register. Modem | | | can shift to a slower speed if necessary. | | | | | | In answer mode, handshake attempted with | | | the following protocols in order - V.FC, | | | V.32bis, V.32, V.22bis, V.22 or Bell 212, | | | V.21, and Bell 103 | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE | |------------------------------------------------------------| | Type: | Immediate | |---------------+--------------------------------------------| | Format: | AT [cmds] On [cmds] | |---------------+--------------------------------------------| | Description: | Controls on-line command (data | | | transmission) state options. | |------------------------------------------------------------| | Note: The O command must be placed at the end of the | | command string. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | On-line command mode with no retraining | | | enabled | |---------------+--------------------------------------------| | O1 | On-line command mode with retraining | | | enabled | |---------------+--------------------------------------------| | O3 | Issue a rate re-negotiate, then return to | | | on-line state | +------------------------------------------------------------+ +------------------------------------------------------------+ | SELECT CALL PROGRESS RESULT CODES | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] Xn [cmds] | |--------------+---------------------------------------------| | Description: | Enables selection of tone detection and | | | associated result code format options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | X0 | Busy and dial tone detection disabled; | | | result codes 0 - 4 enabled. | |--------------+---------------------------------------------| | X1 | Busy and dial tone detection disabled; | | | result codes 0 - 5 & 10 enabled. | |--------------+---------------------------------------------| | X2 | Busy tone detection disabled, dial tone | | | detection enabled; result codes 0 - 6 & 10 | | | enabled. | |--------------+---------------------------------------------| | X3 | Busy tone detection enabled, dial tone | | | detection disabled; result codes 0 - 5, 7 & | | | 10 enabled. | |--------------+---------------------------------------------| | i X4 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X5 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X6 | Busy and dial tone detection enabled; | | | result codes 0 - 7 & 10 enabled. | |--------------+---------------------------------------------| | X7 | Display CONNECT or "1" for all speeds. | | | Check dial tone and busy tone | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Zn [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM using the &W command. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | Z0 | Restore setting 0 | |--------------+---------------------------------------------| | Z1 | Restore setting 0 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Dn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem response to DTR | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &D0 | Modem does not respond to DTR | |--------------+---------------------------------------------| | &D1 | Modem goes to command mode after DTR goes | | | is off | |--------------+---------------------------------------------| | &D2 | Modem goes to command mode and disconnects | | | (hangs up) after DTR goes off; Auto-Answer | | | is disabled. | |--------------+---------------------------------------------| | &D3 | Modem is initialized after DTR goes off | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Kn [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | i &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PULSE DIALING RATIO | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Pn [cmds] | |--------------+---------------------------------------------| | Description: | Selects pulse dial make/break ratio | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i &P0 | 39/61ms at 10pps (North America) | |--------------+---------------------------------------------| | &P1 | 33/67ms at 10pps (Europe) | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Qn [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | i &Q0 | Buffered asynchronous mode, serial port | | | speed follows connect speed. | |--------------+---------------------------------------------| | &Q5 | Error correction mode | |--------------+---------------------------------------------| | &Q8 | MNP error control mode | |--------------+---------------------------------------------| | &Q9 | V.42 or MNP error control mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Sn [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | i &S1 | DSR high only while modem is handshaking or | | | connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST MODES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] &Tn | |--------------+---------------------------------------------| | Description: | Selects test options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &T0 | End current test | |--------------+---------------------------------------------| | &T1 | Begin local analog loopback test | |--------------+---------------------------------------------| | &T3 | Begin local digital loopback | |--------------+---------------------------------------------| | &T6 | Request remote digital loopback | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORE ACTIVE PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Wn [cmds] | |--------------+---------------------------------------------| | Description: | Writes the values for the active profile | | | into the non-volatile RAM | +------------------------------------------------------------+ Extended AT Commands +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the type of connection the modem | | | will operate in | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N1 | Direct mode enabled | |--------------+---------------------------------------------| | \N2 | Reliable mode enabled | |--------------+---------------------------------------------| | \N3 | Auto-reliable mode enabled | |--------------+---------------------------------------------| | \N4 | V.42 reliable mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q3 | Bidirectional RTS/CTS flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BLACKLIST | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Bn [cmds] | |--------------+---------------------------------------------| | Description: | View numbers in blacklist | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %Cn [cmds] | |--------------+---------------------------------------------| | Description: | Selects data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | %C1 | V.42bis/MNP5 enabled | +------------------------------------------------------------+ S(status) -REGISTERS +------------------------------------------------------------+ | V.34 MODULATION | |------------------------------------------------------------| | Format | AT [cmds] S28=n [cmds] | |--------------+---------------------------------------------| | Default: | 1 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Controls the V.34 modulation | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S28=0 | Disabled | |--------------+---------------------------------------------| | S28=1-255 | Enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | ERROR CORRECTION NEGOTIATION | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S36=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects the action of the modem if it fails | | | to connect with the error-correction | | | protocol set in &Q. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S36=0, 2 | Hang up | |--------------+---------------------------------------------| | S36=1, 3 | Attempt a direct connection | |--------------+---------------------------------------------| | S36=4, 6 | Attempt a connection at MNP2-4; if that | | | fails, hang up. | |--------------+---------------------------------------------| | S36=5, 7 | Attempt a connection at MNP2-4; if that | | | fails, attempt a direct connection. | +------------------------------------------------------------+ +------------------------------------------------------------+ | DCE LINE SPEED | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S37=n [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum allowable data exchange | | | rate attempted during handshake process. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i S37=0 | Maximum modem speed | |--------------+---------------------------------------------| | S37=2 | 1200/75bps | |--------------+---------------------------------------------| | S37=3 | 300bps | |--------------+---------------------------------------------| | S37=5 | 1200bps | |--------------+---------------------------------------------| | S37=6 | 2400bps | |--------------+---------------------------------------------| | S37=7 | 4800bps | |--------------+---------------------------------------------| | S37=8 | 7200bps | |--------------+---------------------------------------------| | S37=9 | 9600bps | |--------------+---------------------------------------------| | S37=10 | 12000bps | |--------------+---------------------------------------------| | S37=11 | 14400bps | |--------------+---------------------------------------------| | S37=12 | 16800bps | |--------------+---------------------------------------------| | S37=13 | 19200bps | |--------------+---------------------------------------------| | S37=14 | 21600bps | |--------------+---------------------------------------------| | S37=15 | 24000bps | |--------------+---------------------------------------------| | S37=16 | 26400bps | |--------------+---------------------------------------------| | S37=17 | 28800bps | |--------------+---------------------------------------------| | S37=18 | 31200bps | |--------------+---------------------------------------------| | S37=19 | 33600bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL LINE RATE | |------------------------------------------------------------| | Type: | Register | |--------------------+---------------------------------------| | Format | AT [cmds] S38=n [cmds] | |--------------------+---------------------------------------| | Description: | 56K dial line rate selection | |------------------------------------------------------------| | Command | Function | |------------+-----------------------------------------------| | i S38=0 | 56K disabled | |------------+-----------------------------------------------| | S38=1 | 56K enabled, auto-speed selection, maximum | | | modem speed | |------------+-----------------------------------------------| | S38=2 | 32000bps | |------------+-----------------------------------------------| | S38=3 | 34000bps | |------------+-----------------------------------------------| | S38=4 | 36000bps | |------------+-----------------------------------------------| | S38=5 | 38000bps | |------------+-----------------------------------------------| | S38=6 | 40000bps | |------------+-----------------------------------------------| | S38=7 | 42000bps | |------------+-----------------------------------------------| | S38=8 | 44000bps | |------------+-----------------------------------------------| | S38=9 | 46000bps | |------------+-----------------------------------------------| | S38=10 | 48000bps | |------------+-----------------------------------------------| | S38=11 | 50000bps | |------------+-----------------------------------------------| | S38=12 | 52000bps | |------------+-----------------------------------------------| | S38=13 | 54000bps | |------------+-----------------------------------------------| | S38=14 | 56000bps | +------------------------------------------------------------+ +------------------------------------------------------------+ | SLEEP TIMER | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S89 [cmds] | |--------------+---------------------------------------------| | Range: | 0 - 60 | |--------------+---------------------------------------------| | Unit: | 1 second | |--------------+---------------------------------------------| | Description: | Sleep mode control timer | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | 0 | Disable sleep mode | |--------------+---------------------------------------------| | 5 - 60 | Number of seconds of inactivity before | | | entering sleep mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TRANSMISSION LEVEL (JAPANESE VERSION ONLY) | |------------------------------------------------------------| | Type | Register or Configuration | |-------------+----------------------------------------------| | Format | AT [cmds] S91=n [cmds] | |-------------+----------------------------------------------| | Default | 14 | |-------------+----------------------------------------------| | Range | 6 - 15 | |-------------+----------------------------------------------| | Unit | -1 dBm | |-------------+----------------------------------------------| | Description | Sets the signal level for transmission over | | | leased-lines | +------------------------------------------------------------+ +------------------------------------------------------------+ | FEATURE NEGOTIATION OPTIONS | |------------------------------------------------------------| | Type: | Register | |------------------------------------------------------------| | Format: | AT [cmds] S48=n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active error correction and | | | compression protocols | |------------------------------------------------------------| | Command | Function | |----------------+-------------------------------------------| | S48=7 | Detection negotiation and XID negotiation | | | enabled | |----------------+-------------------------------------------| | S48=128 | Fall-back to options set in S36 | +------------------------------------------------------------+