TORNADO CO., LTD ================ WEBJET 128 Card Type ISDN TA Chip Set Unidentified I/O Options RJ-45 ISDN BRI U interface, 9-pin DTE port, power, microphone in, speaker out ISDN Rate 230.4Kbps ISDN Modulation PPP, MLPPP, V.120 Protocol Error Unidentified Correction/Compression Data Bus External +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |---------------------------+-------+----------------+-------| | ISDN BRI interface | CN1 | 9-pin DTE port | CN4 | | (RJ-45) | | | | |---------------------------+-------+----------------+-------| | Microphone in | CN2 | Power | CN5 | |---------------------------+-------+----------------+-------| | Speaker out | CN3 | Power switch | SW1 | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAGNOSTIC LED(S) | |------------------------------------------------------------| | LED | Color | Status | Condition | |------+----------------+----------+-------------------------| | DATA | Unidentified | On | DTR is high | |------+----------------+----------+-------------------------| | DATA | Unidentified | Blinking | Serial data transfer | | | | | active | |------+----------------+----------+-------------------------| | DATA | Unidentified | Off | Serial data transfer | | | | | not in progress | |------+----------------+----------+-------------------------| | B1 | Unidentified | On | B-channel 1 data call | | | | | connected | |------+----------------+----------+-------------------------| | B1 | Unidentified | Off | No activity on | | | | | B-channel 1 | |------+----------------+----------+-------------------------| | B2 | Unidentified | On | B-channel 2 data call | | | | | connected | |------+----------------+----------+-------------------------| | B2 | Unidentified | Off | No activity on | | | | | B-channel 2 | |------+----------------+----------+-------------------------| | PWR | Unidentified | On | Power is on | |------+----------------+----------+-------------------------| | PWR | Unidentified | Off | Power is off | +------------------------------------------------------------+ +---------------------------------------------------+ | SUPPORTED COMMAND SET | |---------------------------------------------------| | Basic AT Commands | |---------------------------------------------------| | AT, '+++', A/ | |---------------------------------------------------| | A, E, Q, V, W, X | |---------------------------------------------------| | &F, &V | |---------------------------------------------------| | S Registers | |---------------------------------------------------| | S0, S2, S3, S4, S5, S7, S25 | |---------------------------------------------------| | Note: | | | | See MHI Help File for full command documentation. | +---------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &M n [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &M0 | Asynchronous mode | |--------------+---------------------------------------------| | &M1 | Synchronous connect mode and asynchronous | | | off-line command mode. | |--------------+---------------------------------------------| | &M2 | Synchronous connect mode and asynchronous | | | off-line command mode and set DTR high. | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMMUNICATIONS MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Q n [cmds] | |--------------+---------------------------------------------| | Description: | Selects communications mode options | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &Q0 | Asynchronous mode, serial port speed | | | follows connect speed. | |--------------+---------------------------------------------| | &Q1 | Asynchronous off-line command mode and | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q2 | Asynchronous off-line command mode - modem | | | autodials first number in directory, then | | | synchronous connect mode. | |--------------+---------------------------------------------| | &Q3 | Asynchronous off-line command mode on low | | | DTR, synchronous connect mode on high DTR. | |--------------+---------------------------------------------| | &Q4 | Auto-synchronous mode | |--------------+---------------------------------------------| | &Q5 | Error correction mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA CARRIER DETECT (DCD) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &C n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the DCD option is enabled | | | or disabled | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &C0 | DCD enabled | |--------------+---------------------------------------------| | &C1 | DCD enabled after carrier signal detected | |--------------+---------------------------------------------| | &C2 | DCD enabled when on-line, low at loss of | | | carrier, enabled again at idle | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA SET READY (DSR) | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &S n [cmds] | |--------------+---------------------------------------------| | Description: | Selects DSR options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &S0 | DSR forced high | |--------------+---------------------------------------------| | &S1 | DSR high only while modem is connected | |--------------+---------------------------------------------| | &S2 | DSR high only while modem is connected | +------------------------------------------------------------+ +------------------------------------------------------------+ | DATA TERMINAL READY (DTR) | |------------------------------------------------------------| | Type: | Configuration | | |--------------+---------------| | | Format: | AT [cmds] &D | | | | n [cmds] | | |--------------+---------------| | | Description: | Selects modem | | | | response to | | | | DTR | | |------------------------------------------------------------| | Note: The action each variant of &D causes depends on | | the setting of &Q | |------------------------------------------------------------| | &Q Setting | &D0 | &D1 | &D2 | &D3 | |--------------+---------------+---------+---------+---------| | &Q0, &Q5 | Command 0 | Command | Command | Command | | | | 1 | 2 | 4 | |--------------+---------------+---------+---------+---------| | &Q1 | Command 2 | Command | Command | Command | | | | 1 | 2 | 4 | |--------------+---------------+---------+---------+---------| | &Q2 | Command 2 | Command | Command | Command | | | | 2 | 2 | 2 | |--------------+---------------+-----------------------------| | Command | Function | | |--------------+---------------| | | Command 0 | Modem does | | | | not respond | | | | to DTR | | |--------------+---------------| | | Command 1 | Modem goes to | | | | command mode | | | | after DTR | | | | goes is off | | |--------------+---------------| | | Command 2 | Modem goes to | | | | command mode | | | | and | | | | disconnects | | | | (hangs up) | | | | after DTR | | | | goes off; | | | | Auto-Answer | | | | is disabled. | | |--------------+---------------| | | Command 3 | Modem is | | | | initialized | | | | after DTR | | | | goes off | | +------------------------------------------------------------+ +------------------------------------------------------------+ | DIAL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] D<#> [cmds] | |--------------+---------------------------------------------| | Description: | Dials telephone number according to any | | | modifiers included in the string | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &K n [cmds] | |--------------+---------------------------------------------| | Description: | Enables flow control options | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | &K0 | Flow control disabled | |--------------+---------------------------------------------| | &K1 | RTS to CTS flow control enabled | |--------------+---------------------------------------------| | &K2 | XON/XOFF flow control enabled | |--------------+---------------------------------------------| | &K3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | &K4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | HOOK CONTROL | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] H n [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether the modem is on-hook or | | | off-hook | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | H0 | Modem commanded to go on-hook (hang-up) | +------------------------------------------------------------+ +------------------------------------------------------------+ | ON-LINE | |------------------------------------------------------------| | Type: | Immediate | |---------------+--------------------------------------------| | Format: | AT [cmds] O n [cmds] | |---------------+--------------------------------------------| | Description: | Controls on-line command (data | | | transmission) state options. | |------------------------------------------------------------| | Note: The O command must be placed at the end of the | | command string. | |------------------------------------------------------------| | Command | Function | |---------------+--------------------------------------------| | O0 | On-line command mode with no retraining | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &O n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active protocol | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | &O7 | PPP, 1 x B | |--------------+---------------------------------------------| | &O8 | V.14, 1 x B | |--------------+---------------------------------------------| | &O9 | V.110, 1 x B | |--------------+---------------------------------------------| | &O10 | V.120, 1 x B | |--------------+---------------------------------------------| | &O13 | Multi Link V.120, 2 x B | |--------------+---------------------------------------------| | &O16 | GCI-speech, 2 x B | |--------------+---------------------------------------------| | &O18 | GCI-data, 2 x B | |--------------+---------------------------------------------| | &O27 | Multi Link PPP, 2 x B | +------------------------------------------------------------+ +------------------------------------------------------------+ | REPORT INFORMATION | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] I n [cmds] | |--------------+---------------------------------------------| | Description: | Displays information requested | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | I0 | Reports hardware identification | |--------------+---------------------------------------------| | I1 | Reports ROM checksum | |--------------+---------------------------------------------| | I2 | Tests and reports ROM checksum | |--------------+---------------------------------------------| | I3 | Reports product name and software revision | |--------------+---------------------------------------------| | I4 | Reports manufacturer information | |--------------+---------------------------------------------| | I5 | Reports protocol options | |--------------+---------------------------------------------| | I8 | Reports Euro-ISDN software version | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESTORE PROFILE ON POWER-UP | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &Y n [cmds] | |--------------+---------------------------------------------| | Description: | Restores a selected profile into the active | | | profile on power-up (hard reset). | +------------------------------------------------------------+ +------------------------------------------------------------+ | RTS/CTS | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &R n [cmds] | |--------------+---------------------------------------------| | Description: | Command function currently unidentified | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] Z n [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM using the &W command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORE ACTIVE PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] &W n [cmds] | |--------------+---------------------------------------------| | Description: | Writes the values for the active profile | | | into the non-volatile RAM | +------------------------------------------------------------+ EXTENDED AT COMMANDS +------------------------------------------------------------+ | CONFIGURATION PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] /S [cmds] | |--------------+---------------------------------------------| | Description: | Displays active and stored configuration | | | profiles | +------------------------------------------------------------+ SPECIAL COMMANDS +------------------------------------------------------------+ | PROTOCOL SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #CH= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects active protocol | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | #CH=7 | PPP, 1 x B | |--------------+---------------------------------------------| | #CH=8 | V.14, 1 x B | |--------------+---------------------------------------------| | #CH=9 | V.110, 1 x B | |--------------+---------------------------------------------| | i | V.120, 1 x B | |--------------+---------------------------------------------| | #CH=13 | Multi Link V.120, 2 x B | |--------------+---------------------------------------------| | #CH=16 | GCI-speech, 2 x B | |--------------+---------------------------------------------| | #CH=18 | GCI-data, 2 x B | |--------------+---------------------------------------------| | #CH=27 | Multi Link PPP, 2 x B | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE NUMBER SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #REMNBRC= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects remote control number | +------------------------------------------------------------+ +------------------------------------------------------------+ | REMOTE PASSWORD SELECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #PASSRC= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects remote control password | +------------------------------------------------------------+ +------------------------------------------------------------+ | RING MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] #RM= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects ring mode | |--------------+---------------------------------------------| | Command | Mode | |--------------+---------------------------------------------| | #RM0 | Selects ring mode by subnumber or MSN | |--------------+---------------------------------------------| | #RM1 | Pass on call to active profile | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #Z n [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM using the &W command. | +------------------------------------------------------------+ +------------------------------------------------------------+ | STORED PROFILES | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] #V [cmds] | |--------------+---------------------------------------------| | Description: | Displays list of stored parameters in short | | | form | +------------------------------------------------------------+ S(STATUS) -REGISTERS +------------------------------------------------------------+ | ACTIVE PROFILE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S110= n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Selects active profile | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTOBAUD | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S124= n [cmds] | |--------------+---------------------------------------------| | Description: | Enables/disables autobaud function | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S124=0 | Autobaud disabled | |--------------+---------------------------------------------| | S124=1 | Autobaud enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S112 | |------------------------------------------------------------| | Format: | AT [cmds] | | | | S112= n | | | | [cmds] | | |--------------+--------------| | | Range: | Unidentified | | |--------------+--------------| | | Unit: | Bit-mapped | | |--------------+--------------| | | Description: | Controls | | | | ring message | | | | format | | |--------------+--------------+------------------------------| | Bit | Value | Function | |--------------+--------------+------------------------------| | 0 | 0 | Standard AT RING message | | | | format (RING) | | | 1 | | | | | Extended AT RING message | | | | format (RING J | |--------------+--------------+------------------------------| | 1 | 0 | Extended result codes | | | | disabled | | | 1 | | | | | Extended result codes | | | | enabled | |--------------+--------------+------------------------------| | 2 | 0 | Not used | |--------------+--------------+------------------------------| | 3 | 0 | Standard AT format | | | | | | | 1 | Extended AT format | |--------------+--------------+------------------------------| | 6 - 4 | 0 | Not used | |--------------+--------------+------------------------------| | 7 | 0 | Additional service messages | | | | disabled | | | 1 | | | | | Additional service messages | | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | DTR COMMAND | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S123= n [cmds] | |--------------+---------------------------------------------| | Description: | Enables &D command | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S123=0 | &D enabled for DTR functions | |--------------+---------------------------------------------| | S123=1 | DTR ingnored. &D command disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | EXTENDED RESULT CODES | |------------------------------------------------------------| | Type: | Register | | |--------------+-------------| | | Format | AT [cmds] | | | | S95= n | | | | [cmds] | | |--------------+-------------| | | Range: | 0-255 | | |--------------+-------------| | | Unit: | Bit-mapped | | |--------------+-------------| | | Description: | Works in | | | | combination | | | | with the W | | | | n command | | | | to enable | | | | extended | | | | result | | | | codes. | | | | Features | | | | enabled by | | | | S95 take | | | | precedence | | | | over the | | | | options | | | | selected by | | | | W n . | | |--------------+-------------+-------------------------------| | Bit | Value | Function | |--------------+-------------+-------------------------------| | 0 | 0 | CONNECT result code reports | | | | DTE speed. | | | 1 | | | | | CONNECT result code reports | | | | line speed instead DTE speed. | |--------------+-------------+-------------------------------| | 1 | 0 | Verbose CONNECT result codes | | | | display DTE or line speed | | | 1 | only. | | | | | | | | Adds "/ARQ" to all verbose | | | | CONNECT result codes except | | | | "NONE." | |--------------+-------------+-------------------------------| | 2 | 0 | CARRIER result codes | | | | disabled. | | | 1 | | | | | CARRIER result codes enabled. | |--------------+-------------+-------------------------------| | 3 | 0 | PROTOCOL result codes | | | | disabled. | | | 1 | | | | | PROTOCOL result codes | | | | enabled. | +------------------------------------------------------------+ +------------------------------------------------------------+ | FACTORY DEFAULT PROFILE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] S121= n [cmds] | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Description: | Sets values in active profile to values | | | found in the default profile | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S121=0 | Retrieve factory settings and restart | |--------------+---------------------------------------------| | S121=255 | Disabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S39? [cmds] | |--------------+---------------------------------------------| | Description: | Displays the current flow control | |--------------+---------------------------------------------| | Value | Meaning | |--------------+---------------------------------------------| | 0 | Flow control disabled | |--------------+---------------------------------------------| | 3 | RTS/CTS flow control enabled | |--------------+---------------------------------------------| | 4 | XON/XOFF flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | PROTOCOL SERVICE | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S111= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects options for protocol service | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | 1 | Voice service | |--------------+---------------------------------------------| | 2 | Data modem service | |--------------+---------------------------------------------| | 3 | Raw data service | |--------------+---------------------------------------------| | 4 | Group 3 fax service | |--------------+---------------------------------------------| | 5 | V.14 | |--------------+---------------------------------------------| | 7 | PAD service | |--------------+---------------------------------------------| | 8 | V.120 service | |--------------+---------------------------------------------| | 10 | Synchronous relay service | +------------------------------------------------------------+ +------------------------------------------------------------+ | RING MESSAGE TIMER | |------------------------------------------------------------| | Type: | Register | |---------------+--------------------------------------------| | Format | AT [cmds] S117= n [cmds] | |---------------+--------------------------------------------| | Range: | 0-255 | |---------------+--------------------------------------------| | Unit: | 1 second | |---------------+--------------------------------------------| | Description: | Maximum duration allowed between two | | | consecutive RING messages | |------------------------------------------------------------| | Note: S117=0 allows for a single RING message only | +------------------------------------------------------------+ +------------------------------------------------------------+ | SERIAL ASYNCHRONOUS RATE & CLOCK SELECTION | |------------------------------------------------------------| | Type: | Register | |--------------+---------------------------------------------| | Format | AT [cmds] S114= n [cmds] | |--------------+---------------------------------------------| | Description: | Selects sserial asynchronous speed & clock | | | selection | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S114=0 | External clock source | |--------------+---------------------------------------------| | S114=1 | 1200bps | |--------------+---------------------------------------------| | S114=2 | 2400bps | |--------------+---------------------------------------------| | S114=3 | 300bps | |--------------+---------------------------------------------| | S114=4 | 4800bps | |--------------+---------------------------------------------| | S114=7 | 7200bps | |--------------+---------------------------------------------| | S114=9 | 9600bps | |--------------+---------------------------------------------| | S114=12 | 1200bps | |--------------+---------------------------------------------| | S114=14 | 14.400bps | |--------------+---------------------------------------------| | S114=19 | 19.2Kbps | |--------------+---------------------------------------------| | S114=24 | 2400bps | |--------------+---------------------------------------------| | S114=28 | 28.8Kbps | |--------------+---------------------------------------------| | S114=38 | 38.4Kbps | |--------------+---------------------------------------------| | S114=48 | 4800bps | |--------------+---------------------------------------------| | S114=20 | 57.6Kbps | |--------------+---------------------------------------------| | S114=72 | 7200bps | |--------------+---------------------------------------------| | S114=75 | 75bps | |--------------+---------------------------------------------| | S114=96 | 9600bps | |--------------+---------------------------------------------| | S114=115 | 115.2Kbps | |--------------+---------------------------------------------| | S114=255 | Internal clock source | +------------------------------------------------------------+ +------------------------------------------------------------+ | SOFT RESET | |------------------------------------------------------------| | Type: | Immediate | |--------------+---------------------------------------------| | Format: | AT [cmds] S122= n [cmds] | |--------------+---------------------------------------------| | Description: | Restores modem profiles previously saved in | | | non-volatile RAM using the &W command. | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | S122=0 | Restore setting | |--------------+---------------------------------------------| | S122=255 | Disabled | +------------------------------------------------------------+