TEXT View Source
# STAR LOGIC, INC.
RM2422E
Card Type Fax, Modem (asynchronous), Network
Interface Card
Chip Set Rockwell
Maximum Network Rate 10Mbps
Maximum Modem Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103A/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, V.42bis
Correction/Compression
Topology Star
Wiring Type Unshielded twisted pair
Boot ROM Not available
IMG IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------+-------+-------------------------+-------|
| Line out - RJ-11 | CN1 | 10Base-T network | CN2 |
| | | connection - RJ-45 | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED | Color | Status | Condition |
|-----+-------+--------+-------------------------------------|
| 1 | Red | On | Twisted pair network connection is |
| | | | good |
|-----+-------+--------+-------------------------------------|
| 1 | Red | Off | Twisted pair network connection is |
| | | | broken |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUDIO OUTPUT LEVEL |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #TL n [cmds] |
|-------------+----------------------------------------------|
| Default | 32767 |
|-------------+----------------------------------------------|
| Range | 0-32767 |
|-------------+----------------------------------------------|
| Unit | Unidentified |
|-------------+----------------------------------------------|
| Description | Sets the transmit level of the data pump |
| | audio output |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RETRAIN - FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] %E n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Controls auto-retrain mode and |
| | | fallback/fall-forward |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| | %E0 | Auto-retrain disabled |
|---+--------------+-----------------------------------------|
| | %E1 | Auto-retrain enabled |
|---+--------------+-----------------------------------------|
| » | %E2 | Auto-fallback/fall-forward enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BAUD RATE |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #BDR= n [cmds] |
|-------------+----------------------------------------------|
| Default | 0 |
|-------------+----------------------------------------------|
| Range | 0-48 |
|-------------+----------------------------------------------|
| Unit | current speed |
|-------------+----------------------------------------------|
| Description | Selects a baud rate without speed detection |
| | at the serial port. #BDR=0, Enables autobaud |
| | detection |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BEEP TONE TIMER |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #VBT= n [cmds] |
|-------------+----------------------------------------------|
| Default | 10 |
|-------------+----------------------------------------------|
| Range | 0-40 |
|-------------+----------------------------------------------|
| Unit | .1 second |
|-------------+----------------------------------------------|
| Description | Sets the time period which is used by the |
| | modem as the DTMF for generating tones while |
| | in on-line voice command mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S14 |
|------------------------------------------------------------|
| Format | AT [cmds] S14= n | |
| | [cmds] | |
|------------------+------------------| |
| | Default: | 138 | |
|---+--------------+------------------| |
| | Range: | 0-255 | |
|---+--------------+------------------| |
| | Unit: | Bit-mapped | |
|---+--------------+------------------| |
| | Description: | Controls echo, | |
| | | result codes, | |
| | | result code | |
| | | display, dial | |
| | | mode, and | |
| | | answer/originate | |
| | | mode. | |
|---+--------------+------------------+----------------------|
| | Bit | Value | Function |
|---+--------------+------------------+----------------------|
| | 0 | 0 | Not used |
|---+--------------+------------------+----------------------|
| | 1 | 0 | Command echo |
| | | | disabled |
| | | 1 | |
| | | | Command echo enabled |
|---+--------------+------------------+----------------------|
| | 2 | 0 | Result codes enabled |
| | | | |
| | | 1 | Result codes |
| | | | disabled |
|---+--------------+------------------+----------------------|
| | 3 | 0 | Display result codes |
| | | | in numeric format |
| | | 1 | |
| | | | Display result codes |
| | | | in verbose format |
|---+--------------+------------------+----------------------|
| | 4 | 0 | Not used |
|---+--------------+------------------+----------------------|
| | 5 | 0 | Tone dial enabled |
| | | | |
| | | 1 | Pulse dial enabled |
|---+--------------+------------------+----------------------|
| | 6 | 0 | Not used |
|---+--------------+------------------+----------------------|
| | 7 | 0 | Answer mode enabled |
| | | | |
| | | 1 | Originate mode |
| | | | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S21 |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S21= n | |
| | [cmds] | |
|------------------+------------| |
| | Default: | 4 | |
|---+--------------+------------| |
| | Range: | 0-253 | |
|---+--------------+------------| |
| | Unit: | Bit-mapped | |
|---+--------------+------------| |
| | Description: | Selects | |
| | | jack type, | |
| | | CTS | |
| | | signal, | |
| | | low DTR | |
| | | action, | |
| | | DCD | |
| | | signal, | |
| | | DSR | |
| | | signal, | |
| | | and the | |
| | | long space | |
| | | disconnect | |
| | | function. | |
|---+--------------+------------+----------------------------|
| | Bit | Value | Function |
|---+--------------+------------+----------------------------|
| | 0 | 0 | Selects RJ-11, RJ-41S, or |
| | | | RJ45S jack |
| | | 1 | |
| | | | Selects RJ-12 or RJ-13 |
| | | | jack |
|---+--------------+------------+----------------------------|
| | 1 | 0 | Not used |
|---+--------------+------------+----------------------------|
| | 2 | 0 | CTS follows RTS |
| | | | |
| | | 1 | CTS forced high |
|---+--------------+------------+----------------------------|
| | 4, 3 | 00 | DTR signal ignored |
| | | | |
| | | 01 | Modem goes to command mode |
| | | | on low DTR |
| | | 10 | |
| | | | Modem disconnects on low |
| | | 11 | DTR. Auto-Answer is |
| | | | disabled. |
| | | | |
| | | | Modem is initialized on |
| | | | low DTR |
|---+--------------+------------+----------------------------|
| | 5 | 0 | DCD forced high |
| | | | |
| | | 1 | DCD normal |
|---+--------------+------------+----------------------------|
| | 6 | 0 | DSR forced high |
| | | | |
| | | 1 | DSR normal |
|---+--------------+------------+----------------------------|
| | 7 | 0 | Long space disconnect |
| | | | function disabled |
| | | 1 | |
| | | | Long space disconnect |
| | | | function enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S22 |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S22= n | |
| | [cmds] | |
|------------------+------------| |
| | Default: | 117 | |
|---+--------------+------------| |
| | Range: | 0-127 | |
|---+--------------+------------| |
| | Unit: | Bit-mapped | |
|---+--------------+------------| |
| | Description: | Controls | |
| | | speaker | |
| | | volume and | |
| | | controls, | |
| | | and limits | |
| | | results | |
| | | codes. | |
|---+--------------+------------+----------------------------|
| | Bit | Value | Function |
|---+--------------+------------+----------------------------|
| | 1, 0 | 00 | Off volume |
| | | | |
| | | 01 | On volume |
| | | | |
| | | 10 | Medium level volume |
| | | | |
| | | 11 | High level volume |
|---+--------------+------------+----------------------------|
| | 3, 2 | 00 | Speaker off |
| | | | |
| | | 01 | Speaker off on carrier |
| | | | |
| | | 10 | Speaker always on |
| | | | |
| | | 11 | Speaker on during |
| | | | handshake |
|---+--------------+------------+----------------------------|
| | 6, 5, 4 | 000 | Basic result codes only |
| | | | enabled |
| | | 100 | |
| | | | Basic and connection speed |
| | | 101 | result codes enabled |
| | | | |
| | | 110 | Basic and connection speed |
| | | | result codes and dialtone |
| | | 111 | detection enabled |
| | | | |
| | | | All result codes except |
| | | | dialtone detection enabled |
| | | | |
| | | | All result codes enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S23 |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S23= n [cmds] | |
|------------------+---------------| |
| | Default: | 54 | |
|---+--------------+---------------| |
| | Range: | 0-255 | |
|---+--------------+---------------| |
| | Unit: | Bit-mapped | |
|---+--------------+---------------| |
| | Description: | Grants/denies | |
| | | remote | |
| | | digital | |
| | | loopback, | |
| | | controls DTE | |
| | | rate and | |
| | | parity, and | |
| | | sets guard | |
| | | tone. | |
|---+--------------+---------------+-------------------------|
| | Bit | Value | Function |
|---+--------------+---------------+-------------------------|
| | 0 | 0 | Remote digital loopback |
| | | | denied |
| | | 1 | |
| | | | Remote digital loopback |
| | | | allowed |
|---+--------------+---------------+-------------------------|
| | 3, 2, 1 | 000 | Sets serial port speed |
| | | | to 0-300bps |
| | | 001 | |
| | | | Sets serial port speed |
| | | 010 | to 600bps |
| | | | |
| | | 011 | Sets serial port speed |
| | | | to 1200bps |
| | | 100 | |
| | | | Sets serial port speed |
| | | 101 | to 2400bps |
| | | | |
| | | 110 | Sets serial port speed |
| | | | to 4800bps |
| | | 111 | |
| | | | Sets serial port speed |
| | | | to 9600bps |
| | | | |
| | | | Sets serial port speed |
| | | | to 19200bps |
| | | | |
| | | | Sets serial port speed |
| | | | to 38400bps |
|---+--------------+---------------+-------------------------|
| | 5,4 | 00 | Parity even |
| | | | |
| | | 01 | Not used |
| | | | |
| | | 10 | Parity odd |
| | | | |
| | | 11 | No Parity |
|---+--------------+---------------+-------------------------|
| | 7, 6 | 00 | Guard tone disabled |
| | | | |
| | | 01 | Guard tone disabled |
| | | | |
| | | 10 | Guard tone 1800Hz |
| | | | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S27 |
|------------------------------------------------------------|
| Format | AT [cmds] S27= n [cmds] | |
|------------------+--------------------------| |
| | Default: | Unidentified | |
|---+--------------+--------------------------| |
| | Range: | Unidentified | |
|---+--------------+--------------------------| |
| | Unit: | Bit-mapped | |
|---+--------------+--------------------------| |
| | Description: | Selects ITU-T/Bell modes | |
|---+--------------+--------------------------+--------------|
| | Bit | Value | Function |
|---+--------------+--------------------------+--------------|
| | 5 - 0 | N/A | Not used |
|---+--------------+--------------------------+--------------|
| | 6 | 0 | CCITT mode |
| | | | |
| | | 1 | Bell mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S28 |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S28= n | |
| | [cmds] | |
|------------------+--------------| |
| | Default: | 0 | |
|---+--------------+--------------| |
| | Range: | 0-255 | |
|---+--------------+--------------| |
| | Unit: | Bit-mapped | |
|---+--------------+--------------| |
| | Description: | Controls | |
| | | pulse | |
| | | dialing and | |
| | | link | |
| | | negotiation. | |
|---+--------------+--------------+--------------------------|
| | Bit | Value | Function |
|---+--------------+--------------+--------------------------|
| | 2 - 0 | 0 | Not used |
|---+--------------+--------------+--------------------------|
| | 4, 3 | 00 | 39ms make/61ms break at |
| | | | 10pps |
| | | 01 | |
| | | | 33ms make/67ms break at |
| | | 10 | 10pps |
| | | | |
| | | 11 | 39ms make/61ms break at |
| | | | 20pps |
| | | | |
| | | | 33ms make/67ms break at |
| | | | 20pps |
|---+--------------+--------------+--------------------------|
| | 5 | 0 | Not used |
|---+--------------+--------------+--------------------------|
| | 7, 6 | 00 | Link will be negotiated |
| | | | at highest possible |
| | | 01 | speed |
| | | | |
| | | 10 | Link will be negotiated |
| | | | at 1200bps |
| | | | |
| | | | Link will be negotiated |
| | | | at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S31 |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S31= n | |
| | [cmds] | |
|------------------+------------| |
| | Default: | 2 | |
|---+--------------+------------| |
| | Range: | 0-9 | |
|---+--------------+------------| |
| | Unit: | Bit-mapped | |
|---+--------------+------------| |
| | Description: | Controls | |
| | | auto-baud | |
| | | function | |
| | | and | |
| | | connect | |
| | | message | |
| | | result | |
| | | codes | |
|---+--------------+------------+----------------------------|
| | Bit | Value | Function |
|---+--------------+------------+----------------------------|
| | 0 | 0 | Not used |
|---+--------------+------------+----------------------------|
| | 1 | 0 | Auto-baud disabled |
| | | | |
| | | 1 | Auto-baud enabled |
|---+--------------+------------+----------------------------|
| | 3, 2 | 00 | DTE speed displayed in |
| | | | result codes |
| | | 01 | |
| | | | Extended result codes |
| | | 10 | enabled; DCE speed |
| | | | displayed in result codes |
| | | | |
| | | | DCE speed displayed in |
| | | | result codes |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S39 |
|------------------------------------------------------------|
| Format | AT [cmds] S39= | |
| | n [cmds] | |
|------------------+----------------| |
| | Default: | 0 | |
|---+--------------+----------------| |
| | Range: | 0-5 | |
|---+--------------+----------------| |
| | Unit: | Bit-mapped | |
|---+--------------+----------------| |
| | Description: | Controls flow | |
| | | control | |
|---+--------------+----------------+------------------------|
| | Bit | Value | Function |
|---+--------------+----------------+------------------------|
| | 2, 1, 0 | 000 | Flow control disabled. |
| | | | |
| | | 011 | RTS/CTS flow control |
| | | | enabled |
| | | 100 | |
| | | | XON/XOFF flow control |
| | | 101 | enabled. |
| | | | |
| | | | Both XON/XOFF and |
| | | | RTS/CTS flow control |
| | | | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S40 |
|------------------------------------------------------------|
| Format | AT [cmds] S40= | |
| | n [cmds] | |
|------------------+-----------------| |
| | Default: | 105 | |
|---+--------------+-----------------| |
| | Range: | 0-255 | |
|---+--------------+-----------------| |
| | Unit: | Bit-mapped | |
|---+--------------+-----------------| |
| | Description: | Controls break | |
| | | handling; | |
| | | selects MNP | |
| | | extended | |
| | | services, and | |
| | | block size. | |
|---+--------------+-----------------+-----------------------|
| | Bit | Value | Function |
|---+--------------+-----------------+-----------------------|
| | 0 | 0 | MNP10 disabled |
| | | | |
| | | 1 | MNP10 enabled |
|---+--------------+-----------------+-----------------------|
| | 2 - 1 | 0 | Not used |
|---+--------------+-----------------+-----------------------|
| | 5, 4, 3 | 000 | \K0 |
| | | | |
| | | 001 | \K1 |
| | | | |
| | | 010 | \K2 |
| | | | |
| | | 011 | \K3 |
| | | | |
| | | 100 | \K4 |
| | | | |
| | | 101 | \K5 |
|---+--------------+-----------------+-----------------------|
| | 7, 6 | 00 | MNP block size is 64 |
| | | | characters |
| | | 01 | |
| | | | MNP block size is 128 |
| | | 10 | characters |
| | | | |
| | | 11 | MNP block size is 192 |
| | | | characters |
| | | | |
| | | | MNP block size is 256 |
| | | | characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S41 |
|------------------------------------------------------------|
| Format | AT [cmds] S41= | |
| | n [cmds] | |
|------------------+-----------------| |
| | Default: | 3 | |
|---+--------------+-----------------| |
| | Range: | 0-15 | |
|---+--------------+-----------------| |
| | Unit: | Bit-mapped | |
|---+--------------+-----------------| |
| | Description: | Selects | |
| | | compression, | |
| | | auto-retrain, | |
| | | flow control, | |
| | | and MNP10 fall | |
| | | back. | |
|---+--------------+-----------------+-----------------------|
| | Bit | Value | Function |
|---+--------------+-----------------+-----------------------|
| | 0 | 0 | Data compression |
| | | | disabled |
| | | 1 | |
| | | | Data compression |
| | | | enabled |
|---+--------------+-----------------+-----------------------|
| | 1 | 0 | Auto-retrain disabled |
| | | | |
| | | 1 | Auto-retrain enabled |
|---+--------------+-----------------+-----------------------|
| | 2 | 0 | Flow control disabled |
| | | | |
| | | 1 | Flow control enabled |
|---+--------------+-----------------+-----------------------|
| | 3 | 0 | MNP10 at 2400 and |
| | | | 1200bps disabled |
| | | 1 | |
| | | | MNP10 at 2400 and |
| | | | 1200bps enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BITS PER SAMPLE |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VBS= n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Selects the type of voice compression |
| | | to be used; ADPCM or linear PCM . |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| | #VBS=2 | 2 bits per sample ADPCM enabled |
|---+--------------+-----------------------------------------|
| » | #VBS=4 | 4 bits per sample ADPCM enabled |
|---+--------------+-----------------------------------------|
| | #VBS=8 | 8 bits per sample PCM enabled |
|------------------------------------------------------------|
| Note: Use with #VSR=7200 or 11025 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \B n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | Unidentified |
|--------------+---------------------------------------------|
| Unit: | .1 second |
|--------------+---------------------------------------------|
| Description: | Sends break to modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
|Type: |Configuration | |
|--------------+----------------| |
| |Format: |AT [cmds] \K n | |
| | |[cmds] | |
|-+------------+----------------| |
| |Description:|Configures | |
| | |action of break | |
| | |signal | |
|-+------------+----------------+----------------------------|
| | Command | Break from DTE |Modem receives| Break |
| | | | \B |received from|
| | | | |remote modem |
|-+------------+----------------+--------------+-------------|
| | \K0 |Online command |Break sent to |Buffers |
| | |mode enabled, |remote modem |cleared, |
| | |send no break to|and buffered |break sent to|
| | |remote modem |cleared |DTE |
|-+------------+----------------+--------------+-------------|
| | \K1 |Break sent to |Break sent to |Buffers |
| | |remote modem and|remote modem |cleared, |
| | |buffered cleared|and buffered |break sent to|
| | | |cleared |DTE |
|-+------------+----------------+--------------+-------------|
| | \K2 |Online command |Send break to |Break sent |
| | |mode enabled, |remote modem |immediately |
| | |send no break to|immediately |to DTE |
| | |remote modem | | |
|-+------------+----------------+--------------+-------------|
| | \K3 |Send break to |Send break to |Break sent |
| | |remote modem |remote modem |immediately |
| | |immediately |immediately |to DTE |
|-+------------+----------------+--------------+-------------|
| | \K4 |Online command |Send break |Break sent |
| | |mode enabled, |with |with received|
| | |send no break to|transmitted |data to the |
| | |remote modem |data |DTE |
|-+------------+----------------+--------------+-------------|
|»| \K5 |Send break with |Send break |Break sent |
| | |transmitted data|with |with received|
| | | |transmitted |data to the |
| | | |data |DTE |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BUFFER SKID |
|------------------------------------------------------------|
| Type | Configuration |
|--------------+---------------------------------------------|
| Format | AT [cmds] #VSK= n [cmds] |
|--------------+---------------------------------------------|
| Default | 255 |
|--------------+---------------------------------------------|
| Range | 255 |
|--------------+---------------------------------------------|
| Unit | 1 byte |
|--------------+---------------------------------------------|
| Description | The modem searches for spare space in the |
| | voice transmit buffer after the XOFF |
| | threshold is reached, during voice |
| | transmission. |
|------------------------------------------------------------|
| Note: Buffer skid is the amount of data the DTE can |
| continue to send after being commanded to stop |
| sending data by the modem. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BUFFER SIZE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VBQ? [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns the size of the voice transmit and |
| | receive buffers |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLER ID |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %CID= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the Caller ID function |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %CID=0 | Caller ID disabled |
|--------------+---------------------------------------------|
| %CID=1 | Caller ID displays formatted data |
|--------------+---------------------------------------------|
| %CID=2 | Caller ID displays raw hexadecimal data |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLER ID MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %CID=? [cmds] |
|--------------+---------------------------------------------|
| Description: | Retrieves the current Caller ID mode from |
| | the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %C n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| %C1 | MNP5 enabled |
|--------------+---------------------------------------------|
| %C2 | V.42bis enabled |
|--------------+---------------------------------------------|
| %C3 | MNP5 and V.42bis enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \N n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enable |
|--------------+---------------------------------------------|
| \N1 | Normal mode enable |
|--------------+---------------------------------------------|
| \N2 | Reliable mode enable |
|--------------+---------------------------------------------|
| \N3 | Auto-reliable mode enable |
|--------------+---------------------------------------------|
| \N4 | LAP-M mode only enable |
|--------------+---------------------------------------------|
| \N5 | MNP mode only enable |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DTMF TONE REPORTING |
|------------------------------------------------------------|
| Type: | Configuration | |
|--------------+---------------| |
| Format: | AT [cmds] | |
| | #VTD= n | |
| | [cmds] | |
|--------------+---------------| |
| Default: | Unidentified | |
|--------------+---------------| |
| Range: | Unidentified | |
|--------------+---------------| |
| Description: | Selects which | |
| | types of | |
| | tones can be | |
| | detected and | |
| | reported to | |
| | the DTE via | |
| | shielded | |
| | codes in | |
| | voice | |
| | transmit, | |
| | voice | |
| | receive, and | |
| | on-line voice | |
| | command | |
| | modes. | |
|--------------+---------------+-----------------------------|
| Bit | Value | Function |
|--------------+---------------+-----------------------------|
| 0 | 0 | DTMF tone capability |
| | | disabled |
| | 1 | |
| | | DTMF tone capability |
| | | enabled |
|--------------+---------------+-----------------------------|
| 1 | 0 | V.25 1300 Hz Calling tone |
| | | capability disabled |
| | 1 | |
| | | V.25 1300 Hz Calling tone |
| | | capability enabled |
|--------------+---------------+-----------------------------|
| 2 | 0 | T.30 1100 Hz Facsimile |
| | | Calling tone capability |
| | 1 | disabled |
| | | |
| | | T.30 1100 Hz Facsimile |
| | | Calling tone capability |
| | | enabled |
|--------------+---------------+-----------------------------|
| 3 | 0 | V.25/T.30 2100 Hz Answer |
| | | tone capability disabled |
| | 1 | |
| | | V.25/T.30 2100 Hz Answer |
| | | tone capability enabled |
|--------------+---------------+-----------------------------|
| 4 | 0 | Bell 2225 Hz Answer tone |
| | | capability disabled |
| | 1 | |
| | | Bell 2225 Hz Answer tone |
| | | capability enabled |
|--------------+---------------+-----------------------------|
| 5 | 0 | Call progress tone and |
| | | cadence capability disabled |
| | 1 | |
| | | call progress tone and |
| | | cadence capability enabled |
|------------------------------------------------------------|
| Note: The modem detects this tone and reports it via |
| a shielded code to the DTE. Tone detection is only |
| performed when the sampling rate is 7.2KHz |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLASH DIAL MODIFIER TIME |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S29= n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | .01 second |
|--------------+---------------------------------------------|
| Description: | Time the modem will go on-hook upon |
| | receiving the ! dial modifier in dial |
| | string |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLASH MEMORY - DOWNLOAD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ** n [cmds] |
|--------------+---------------------------------------------|
| Description: | Downloads new firmware to flash memory |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| **0 | Download at last used serial port speed |
|--------------+---------------------------------------------|
| **1 | Download at 38.4bps |
|--------------+---------------------------------------------|
| **2 | Download at 57.6bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] \G n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Selects modem port flow control |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| » | \G0 | Flow control disabled |
|---+--------------+-----------------------------------------|
| | \G1 | Flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XOFF |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S33= n [cmds] |
|--------------+---------------------------------------------|
| Default: | 19 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XOFF |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XON |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S32= n [cmds] |
|--------------+---------------------------------------------|
| Default: | 17 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XON |
+------------------------------------------------------------+
+------------------------------------------------------------+
| GENERATE TONE SIGNALS - ONLINE VOICE COMMAND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VTS [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls which tones will be issued, DTMF |
| | or other tones, when modem is in on-line |
| | voice command Mode and the sampling rate is |
| | set to 7.2 kHz. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| IDENTIFY COMPRESSION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VCI? [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a unique character string which is |
| | used for identifying proprietary |
| | compression methods of Rockwell ADPCM. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %L [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates the |
| | received line signal level |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL QUALITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Q [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates the line |
| | signal quality |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MAXIMUM BLOCK SIZE FOR TRANSMISSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \A n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the maximum transmittable block size |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \A0 | MNP block size is 64 characters |
|--------------+---------------------------------------------|
| \A1 | MNP block size is 128 characters |
|--------------+---------------------------------------------|
| \A2 | MNP block size is 192 characters |
|--------------+---------------------------------------------|
| \A3 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -K n [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects MNP10 data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -K0 | MNP10 disabled |
|--------------+---------------------------------------------|
| -K1 | MNP10 enabled |
|--------------+---------------------------------------------|
| -K2 | MNP10 enabled on originate mode only |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - FALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Q n [cmds] |
|--------------+---------------------------------------------|
| Description: | Allows MNP10 to fallback to speeds slower |
| | than 4800bps |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -Q0 | MNP10 at 2400 and 1200bps disabled |
|--------------+---------------------------------------------|
| -Q1 | MNP10 at 2400 and 1200bps enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - LINK NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *H n [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the speed at which MNP10 link |
| | negotiation will occur |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *H0 | Link will be negotiated at highest possible |
| | speed |
|--------------+---------------------------------------------|
| *H1 | Link will be negotiated at 1200bps |
|--------------+---------------------------------------------|
| *H2 | Link will be negotiated at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - POWER LEVEL ADJUST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] )M n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls automatic transmit power level |
| | adjustment during MNP 10 link negotiation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| )M0 | Power level adjustment disabled |
|--------------+---------------------------------------------|
| )M1 | Power level adjustment enabled |
|--------------+---------------------------------------------|
| )M2 | Power level adjustment enabled except |
| | during MNP link negotiation |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODE SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #CLS= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Select data, fax or voice/audio mode while |
| | in any mode. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| #CLS=0 | Data mode enabled |
|--------------+---------------------------------------------|
| #CLS=1 | Fax Class 1 mode enabled |
|--------------+---------------------------------------------|
| #CLS=2 | Fax Class 2 mode enabled |
|--------------+---------------------------------------------|
| #CLS=8 | Voice/Audio mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PLAYBACK VOLUME CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VGT [cmds] |
|--------------+---------------------------------------------|
| Default: | 153 |
|--------------+---------------------------------------------|
| Range: | 128-228 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Sets the volume on playback during command |
| | mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT MODEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #MDL? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the model number of the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT MANUFACTURER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #MFR? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the manufacturer of the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT REVISION LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #REV? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the revision number of the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RINGBACK GOES AWAY TIMER - ORIGINATE MODE |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #VRA= n [cmds] |
|-------------+----------------------------------------------|
| Default | 70 |
|-------------+----------------------------------------------|
| Range | 0-255 |
|-------------+----------------------------------------------|
| Unit | .01 second |
|-------------+----------------------------------------------|
| Description | Sets Ringback Goes Away timer; If ringback |
| | is not detected, the modem assumes that the |
| | remote has picked up the line and switches |
| | to on-line voice command Mode. #VRA=0, will |
| | disabled timer. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RINGBACK NEVER CAME TIMER - ORIGINATE |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #VRN= n [cmds] |
|-------------+----------------------------------------------|
| Default | 100 |
|-------------+----------------------------------------------|
| Range | 0-255 |
|-------------+----------------------------------------------|
| Unit | .01 second |
|-------------+----------------------------------------------|
| Description | Sets the "Ringback Never Came" timer; If |
| | ringback is not detected, the modem assumes |
| | the remote has picked up the line and |
| | switches to on-line voice command Mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SAMPLING RATE |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VSR= n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Controls DTE interface speed to |
| | | transmit/receive in voice/audio mode. |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| » | #VSR=7200 | 7200Hz sampling rate enabled |
|---+--------------+-----------------------------------------|
| | #VSR=11025 | 11.025Khz sampling rate enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SILENCE DELETION - VOICE RECEIVE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VSD= n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls silence deletion |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| #VSD=0 | Silence deletion disabled |
|--------------+---------------------------------------------|
| #VSD=1 | Silence deletion enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SILENCE DETECTION TIMER - VOICE RECEIVE |
|------------------------------------------------------------|
| Type | Configuration |
|-------------+----------------------------------------------|
| Format | AT [cmds] #VSP= n [cmds] |
|-------------+----------------------------------------------|
| Default | 55 |
|-------------+----------------------------------------------|
| Range | 0-255 |
|-------------+----------------------------------------------|
| Unit | .1 second |
|-------------+----------------------------------------------|
| Description | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects, while in voice receive mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SILENCE DETECTION TUNER - VOICE RECEIVE |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VSS= n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Controls the sensitivity used by the |
| | | modem in ADPCM compressing periods of |
| | | silence. |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| » | #VSS=0 | Silence detection disabled |
|---+--------------+-----------------------------------------|
| | #VSS=1 | Low sensitive setting enabled |
|---+--------------+-----------------------------------------|
| | #VSS=2 | Midrange sensitive setting enabled |
|---+--------------+-----------------------------------------|
| | #VSS=3 | High sensitive setting enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SLEEP TIMER |
|------------------------------------------------------------|
| Format | AT [cmds] S24= n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | 1 second |
|--------------+---------------------------------------------|
| Description: | Maximum duration of DTE and DCE inactivity |
| | allowed prior to initiating low-power sleep |
| | mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Format | AT [cmds] | |
| | S16= n | |
| | [cmds] | |
|--------------+--------------| |
| Default: | Unidentified | |
|--------------+--------------| |
| Range: | 0-125 | |
|--------------+--------------| |
| Unit: | Bit-mapped | |
|--------------+--------------| |
| Description: | Controls | |
| | loopback | |
| | tests, | |
| | analog, | |
| | digital, | |
| | remote | |
| | digital, and | |
| | self tests. | |
|--------------+--------------+------------------------------|
| Bit | Value | Function |
|--------------+--------------+------------------------------|
| 0 | 0 | Local analog loopback not in |
| | | progress |
| | 1 | |
| | | Local analog loopback in |
| | | progress |
|--------------+--------------+------------------------------|
| 1 | 0 | Not used |
|--------------+--------------+------------------------------|
| 2 | 0 | Local digital loopback not |
| | | in progress |
| | 1 | |
| | | Local digital loopback in |
| | | progress |
|--------------+--------------+------------------------------|
| 3 | 0 | Modem not in remote digital |
| | | loopback |
| | 1 | |
| | | Remote digital loopback in |
| | | progress |
|--------------+--------------+------------------------------|
| 4 | 0 | Remote digital loopback not |
| | | requested |
| | 1 | |
| | | Remote digital loopback |
| | | requested |
|--------------+--------------+------------------------------|
| 5 | 0 | Remote digital loopback w/ |
| | | self-test not in progress |
| | 1 | |
| | | Remote digital loopback w/ |
| | | self-test in progress |
|--------------+--------------+------------------------------|
| 6 | 0 | Local analog loopback w/ |
| | | self-test not in progress |
| | 1 | |
| | | Local analog loopback w/ |
| | | self-test in progress |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODE - PTT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %TT nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Send PTT test signal for line test |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TIMING MARK PLACEMENT |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VTM= n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Controls the placement of timing marks |
| | | by the DCE in the data stream during |
| | | ADPCM recording. |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| » | #VTM=0 | Timing mark placement disabled |
|---+--------------+-----------------------------------------|
| | #VTM=10 | Placement of 1 second intervals enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] @M n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 11-31 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| @M0 | -26dBm |
|--------------+---------------------------------------------|
| @M1 | -30dBm |
|--------------+---------------------------------------------|
| @M2-@M10 | -10dBm |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - FAX |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S92= n [cmds] |
|--------------+---------------------------------------------|
| Default: | 10 |
|--------------+---------------------------------------------|
| Range: | 0-15 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in fax mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - PSTN |
|------------------------------------------------------------|
| Type | Register |
|-------------+----------------------------------------------|
| Format | AT [cmds] S91 =n [cmds] |
|-------------+----------------------------------------------|
| Default | 10 |
|-------------+----------------------------------------------|
| Range | 1-15 |
|-------------+----------------------------------------------|
| Unit | -1 dBm |
|-------------+----------------------------------------------|
| Description | Sets the signal level for transmission over |
| | switched phone lines |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VOICE LINE SELECT |
|------------------------------------------------------------|
| Type: | Configuration |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VLS= n [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Selects which device is routed through |
| | | the modem |
|---+--------------+-----------------------------------------|
| | Command | Function |
|---+--------------+-----------------------------------------|
| » | #VLS=0 | Telephone line interface is routed |
| | | through the modem |
|---+--------------+-----------------------------------------|
| | #VLS=1 | The handset is routed through the modem |
|---+--------------+-----------------------------------------|
| | #VLS=2 | The speaker is routed through the modem |
|---+--------------+-----------------------------------------|
| | #VLS=3 | Auxiliary input device (microphone) is |
| | | routed through the modem |
|---+--------------+-----------------------------------------|
| | #VLS=4 | Telephone line interface and internal |
| | | speaker are routed through the modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VOICE LINE SELECT - DEVICE TYPE |
|------------------------------------------------------------|
| Type: | Response |
|------------------+-----------------------------------------|
| | Format: | AT [cmds] #VLS=? [cmds] |
|---+--------------+-----------------------------------------|
| | Description: | Reports back which device type is |
| | | available for selection |
|---+--------------+-----------------------------------------|
| | Response | Function |
|---+--------------+-----------------------------------------|
| » | 0 | Telephone Line with handset |
|---+--------------+-----------------------------------------|
| | 1 | Handset, headset, or speaker-phone |
| | | powered directly by the modem |
|---+--------------+-----------------------------------------|
| | 2 | Onboard speaker |
|---+--------------+-----------------------------------------|
| | 3 | Microphone |
|---+--------------+-----------------------------------------|
| | 4 | Telephone line with speaker ON and |
| | | handset |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VOICE RECEIVE |
|------------------------------------------------------------|
| Type | Immediate |
|-------------+----------------------------------------------|
| Format | AT [cmds] #VRX [cmds] |
|-------------+----------------------------------------------|
| Description | Sets the modem to voice receive mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VOICE TRANSMIT - ONLINE VOICE COMMAND MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] #VTX [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls when a voice file is to be |
| | transmitted to the line, speaker, or |
| | handset; then switches to voice transmit |
| | mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.32 - COMPROMISE EQUALIZER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] :E n [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls V.32 compromise equalizer |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| :E0 | Equalizer disabled |
|--------------+---------------------------------------------|
| :E1 | Equalizer enabled |
+------------------------------------------------------------+