TEXT View Source
# ACTIONTEC ELECTRONICS, INC.
FME288
Card Type Fax, Modem (synchronous/asynchronous),
Network Interface Card
Chip Set Unidentified
I/O Options Ethernet 10BaseT connector
NIC Type Ethernet
Network Transfer Rate 10Mbps
Maximum Modem Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23,
V.25bis, V.32, V.32bis, V.34
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
Topology Star
Wiring Type Unshielded twisted pair
Boot ROM Not available
V2286
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall-forward |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled |
|--------------+---------------------------------------------|
| %E2 | Auto-fallback/fall-forward enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT MAPPED REGISTERS |
|------------------------------------------------------------|
| Register | Default |
|----------------------------+-------------------------------|
| S28 | Unidentified |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S14 |
|------------------------------------------------------------|
| Format: | AT [cmds] S14=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 138 |
|--------------+---------------------------------------------|
| Range: | 0-174 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls echo, result codes and display, |
| | dial mode, and answer/originate mode. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 1 | 0 | Command echo disabled |
| | | |
| | í 1 | Command echo enabled |
|------+-------+---------------------------------------------|
| 2 | í 0 | Result codes enabled |
| | | |
| | 1 | Result codes disabled |
|------+-------+---------------------------------------------|
| 3 | 0 | Display result codes in numeric format |
| | | |
| | í 1 | Display result codes in verbose format |
|------+-------+---------------------------------------------|
| 4 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 5 | í 0 | Tone dial enabled |
| | | |
| | 1 | Pulse dial enabled |
|------+-------+---------------------------------------------|
| 6 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 7 | 0 | Answer mode enabled |
| | | |
| | í 1 | Originate mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S21 |
|------------------------------------------------------------|
| Format | AT [cmds] S21=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 4 |
|--------------+---------------------------------------------|
| Range: | 0-253 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Selects jack type, CTS/DCD/DSR signals, low |
| | DTR action, and the long space disconnect |
| | function |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | í 0 | Selects RJ-11, RJ-41S, or RJ45S jack |
| | | |
| | 1 | Selects RJ-12 or RJ-13 jack |
|------+-------+---------------------------------------------|
| 1 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 2 | 0 | CTS forced high |
| | | |
| | í 1 | CTS follows RTS |
|------+-------+---------------------------------------------|
| 4, 3 | í 00 | DTR signal ignored |
| | | |
| | 01 | Modem goes to command mode on low DTR |
| | | |
| | 10 | Modem disconnects on low DTR; Auto-Answer |
| | | is disabled |
| | 11 | |
| | | Modem is initialized on low DTR |
|------+-------+---------------------------------------------|
| 5 | í 0 | DCD forced high |
| | | |
| | 1 | DCD normal |
|------+-------+---------------------------------------------|
| 6 | í 0 | DSR forced high |
| | | |
| | 1 | DSR normal |
|------+-------+---------------------------------------------|
| 7 | í 0 | Long space disconnect function disabled |
| | | |
| | 1 | Long space disconnect function enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S22 |
|------------------------------------------------------------|
| Format | AT [cmds] S22=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 117 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls speaker volume and controls, and |
| | limits results codes. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 1, 0 | 00 | Volume off |
| | | |
| | í 01 | Low level volume |
| | | |
| | 10 | Medium level volume |
| | | |
| | 11 | High level volume |
|------+-------+---------------------------------------------|
| 3, 2 | 00 | Speaker off |
| | | |
| | í 01 | Speaker off on carrier |
| | | |
| | 10 | Speaker always on |
| | | |
| | 11 | Speaker on during handshake |
|------+-------+---------------------------------------------|
| 6 - | 000 | Basic result codes only enabled |
| 4 | | |
| | 100 | Basic and connection speed result codes |
| | | enabled |
| | 101 | |
| | | Basic and connection speed result codes and |
| | 110 | dialtone detection enabled |
| | | |
| | í 111 | All result codes except dialtone detection |
| | | enabled |
| | | |
| | | All result codes enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S23 |
|------------------------------------------------------------|
| Format | AT [cmds] S23=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 55 |
|--------------+---------------------------------------------|
| Range: | 0-189 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Grants/denies remote digital loopback, |
| | controls DTE rate and parity, and sets |
| | guard tone |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Remote digital loopback denied |
| | | |
| | í 1 | Remote digital loopback allowed |
|------+-------+---------------------------------------------|
| 3 - | 000 | Sets serial port speed to 0-300bps |
| 1 | | |
| | 001 | Sets serial port speed to 600bps |
| | | |
| | 010 | Sets serial port speed to 1200bps |
| | | |
| | í 011 | Sets serial port speed to 2400bps |
| | | |
| | 100 | Sets serial port speed to 4800bps |
| | | |
| | 101 | Sets serial port speed to 9600bps |
| | | |
| | 110 | Sets serial port speed to 19200bps |
|------+-------+---------------------------------------------|
| 5, 4 | 00 | Parity even |
| | | |
| | 01 | Not used |
| | | |
| | 10 | Parity odd |
| | | |
| | í 11 | No parity |
|------+-------+---------------------------------------------|
| 7, 6 | í 00 | Guard tone disabled |
| | | |
| | 01 | Guard tone disabled |
| | | |
| | 10 | Guard tone 1800Hz enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S27 |
|------------------------------------------------------------|
| Format | AT [cmds] S27=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 74 |
|--------------+---------------------------------------------|
| Range: | 0-111 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Selects synchronous/asynchronous mode, line |
| | type, clock source, and ITU-T/Bell modes. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 3, | 000 | Asynchronous mode, serial port speed |
| 1, 0 | | follows connect speed |
| | 001 | |
| | | Asynchronous off-line command mode and |
| | 010 | synchronous connect mode |
| | | |
| | 011 | Asynchronous off-line command mode; modem |
| | | auto-dials first number in directory, then |
| | 100 | synchronous connect mode |
| | | |
| | 101 | Asynchronous off-line command mode on low |
| | | DTR, synchronous connect mode on high DTR |
| | 111 | |
| | | Auto-synchronous mode |
| | | |
| | | Error correction mode |
| | | |
| | | Buffered asynchronous mode |
|------+-------+---------------------------------------------|
| 2 | 0 | Switched line |
| | | |
| | 1 | Leased line |
|------+-------+---------------------------------------------|
| 5, 4 | 00 | Local modem generates transmit clock source |
| | | |
| | 01 | Local DTE generates transmit clock source |
| | | |
| | 10 | Remote DCE/DTE generates transmit clock |
| | | source |
|------+-------+---------------------------------------------|
| 6 | 0 | ITU/T mode |
| | | |
| | 1 | Bell mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S31 |
|------------------------------------------------------------|
| Format: | AT [cmds] S31=n [cmds] |
|----------------+-------------------------------------------|
| Default: | 2 |
|----------------+-------------------------------------------|
| Range: | 0-2 |
|----------------+-------------------------------------------|
| Description: | Select automode |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | í 0 | Not used |
|----------+-------+-----------------------------------------|
| 1 | 0 | Auto-mode detection disabled |
| | | |
| | í 1 | In originate mode, handshake begins at |
| | | line speed designated by the S37 |
| | | register. Modem can shift to a slower |
| | | speed if necessary. |
| | | |
| | | In answer mode, handshake attempted |
| | | with the following protocols in order - |
| | | V.32bis, V.32, V.22bis, V.22 or Bell |
| | | 212, V.21, and Bell 103 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S40 |
|------------------------------------------------------------|
| Format | AT [cmds] S40=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 105 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls MNP extended services, fallback, |
| | power level, break handling, and block |
| | size. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | MNP extended services disabled |
| | | |
| | 1 | MNP extended services enabled |
|------+-------+---------------------------------------------|
| 1 | 0 | MNP10 at 2400 and 1200bps disabled |
| | | |
| | 1 | MNP10 at 2400 and 1200bps enabled |
|------+-------+---------------------------------------------|
| 2 | í 0 | Power level adjustment enabled |
| | | |
| | 1 | Power level adjustment disabled |
|------+-------+---------------------------------------------|
| 5, | 000 | \K0 |
| 4, 3 | | |
| | 001 | \K1 |
| | | |
| | 010 | \K2 |
| | | |
| | 011 | \K3 |
| | | |
| | 100 | \K4 |
| | | |
| | í 101 | \K5 |
|------+-------+---------------------------------------------|
| 7, 6 | 00 | MNP block size is 64 characters |
| | | |
| | í 01 | MNP block size is 128 characters |
| | | |
| | 10 | MNP block size is 192 characters |
| | | |
| | 11 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S41 |
|------------------------------------------------------------|
| Format | AT [cmds] S41=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-31 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Selects compression, auto-retrain, flow |
| | control, and MNP mode. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 1 - | 00 | Data compression disabled |
| 0 | | |
| | 01 | MNP5 enabled |
| | | |
| | 10 | V.42bis enabled |
| | | |
| | í 11 | MNP5 and V.42bis enabled |
|------+-------+---------------------------------------------|
| 6, 2 | í 00 | Auto-retrain disabled |
| | | |
| | 01 | Auto-retrain enabled |
| | | |
| | 10 | Auto-retrain and auto-fallback enabled |
|------+-------+---------------------------------------------|
| 3 | í 0 | Flow control disabled |
| | | |
| | 1 | Flow control enabled |
|------+-------+---------------------------------------------|
| 4 | í 0 | Stream mode for MNP |
| | | |
| | 1 | Block mode for MNP |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S201 |
|------------------------------------------------------------|
| Format: | AT [cmds] S201=n [cmds] |
|--------------------+---------------------------------------|
| Default: | 32 |
|--------------------+---------------------------------------|
| Range: | 0-62 |
|--------------------+---------------------------------------|
| Description: | Controls power level and compromise |
| | equalizer |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+------------+-----------------------------------|
| 4 - 0 | 00000 | Initial power level -26dBm |
| | | |
| | 00001 | Initial power level -30dBm |
| | | |
| | 00010 | Initial power level -10dBm |
| | | |
| | ... | ... |
| | | |
| | 01010 | Initial power level -10dBm |
| | | |
| | 01011 | Initial power level -11dBm |
| | | |
| | ...to... | ...to... |
| | | |
| | 11110 | Initial power level -30dBm |
|------------------------------------------------------------|
| 5 | 0 | Equalizer disabled |
| | | |
| | 1 | Equalizer enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Bn [cmds] |
|--------------+---------------------------------------------|
| Default: | 3 |
|--------------+---------------------------------------------|
| Range: | 1-9 |
|--------------+---------------------------------------------|
| Unit: | .1 second |
|--------------+---------------------------------------------|
| Description: | Sends break to modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|---------------------+--------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|---------------------+--------------------------------------|
| Description: | Configures action of break signal |
|------------------------------------------------------------|
| Command | Break from | Modem receives | Break received |
| | DTE | \B | from remote |
| | | | modem |
|-----------+--------------+----------------+----------------|
| \K0 | Online | Break sent to | Buffers |
| | command mode | remote modem | cleared, break |
| | enabled, | and buffers | sent to DTE |
| | send no | cleared | |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| \K1 | Break sent | Break sent to | Buffers |
| | to remote | remote modem | cleared, break |
| | modem and | and buffers | sent to DTE |
| | buffers | cleared | |
| | cleared | | |
|-----------+--------------+----------------+----------------|
| \K2 | Online | Send break to | Break sent |
| | command mode | remote modem | immediately to |
| | enabled, | immediately | DTE |
| | send no | | |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| \K3 | Send break | Send break to | Break sent |
| | to remote | remote modem | immediately to |
| | modem | immediately | DTE |
| | immediately | | |
|-----------+--------------+----------------+----------------|
| \K4 | Online | Send break | Break sent |
| | command mode | with | with received |
| | enabled, | transmitted | data to the |
| | send no | data | DTE |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| í \K5 | Send break | Send break | Break sent |
| | with | with | with received |
| | transmitted | transmitted | data to the |
| | data | data | DTE |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| %C1 | MNP5 enabled |
|--------------+---------------------------------------------|
| %C2 | V.42bis enabled |
|--------------+---------------------------------------------|
| %C3 | MNP5 and V.42bis enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | Reliable mode enabled |
|--------------+---------------------------------------------|
| \N3 | Auto-reliable mode enabled |
|--------------+---------------------------------------------|
| \N4 | V.42 reliable mode enabled |
|--------------+---------------------------------------------|
| \N5 | MNP reliable mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Modifier | Function |
|--------------+---------------------------------------------|
| J | Link will be negotiated at highest possible |
| | speed |
|--------------+---------------------------------------------|
| K | Power level adjustment enabled |
|--------------+---------------------------------------------|
| L | Re-dial last number |
|--------------+---------------------------------------------|
| P | Pulse dialing enabled |
|--------------+---------------------------------------------|
| R | Accepted, but not acted upon |
|--------------+---------------------------------------------|
| S=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| T | Tone dialing enabled |
|--------------+---------------------------------------------|
| W | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| ! | Modem commanded to go off-hook for |
| | specified time before returning on-hook |
|--------------+---------------------------------------------|
| @ | Wait for quiet answer |
|--------------+---------------------------------------------|
| , | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| ; | Modem returned to command state after |
| | dialing |
|--------------+---------------------------------------------|
| ^ | Calling tone disabled |
|--------------+---------------------------------------------|
| > | Generate a grounding pulse on ground output |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Gn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects modem port flow control |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \G0 | Flow control disabled |
|--------------+---------------------------------------------|
| \G1 | Flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Read-only Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S39? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays the current flow control |
|--------------+---------------------------------------------|
| Value | Meaning |
|--------------+---------------------------------------------|
| 0 | Flow control disabled |
|--------------+---------------------------------------------|
| í 3 | RTS/CTS flow control enabled |
|--------------+---------------------------------------------|
| 4 | XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| 5 | Transparent XON/XOFF flow control enabled |
|--------------+---------------------------------------------|
| 6 | Both XON/XOFF and RTS/CTS flow control |
| | enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XOFF |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S33=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 19 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XOFF |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XON |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S32=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 17 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XON |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Jn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \J0 | Serial speed locked |
|--------------+---------------------------------------------|
| \J1 | Serial speed follows connect speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MAXIMUM BLOCK SIZE FOR TRANSMISSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \An [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the maximum transmittable block size |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \A0 | MNP block size is 64 characters |
|--------------+---------------------------------------------|
| í \A1 | MNP block size is 128 characters |
|--------------+---------------------------------------------|
| \A2 | MNP block size is 192 characters |
|--------------+---------------------------------------------|
| \A3 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %L [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 9-43 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates the |
| | received line signal level |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL QUALITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Q [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates line signal |
| | quality |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP - EXTENDED SERVICES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects MNP extended services |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -K0 | MNP extended services disabled |
|--------------+---------------------------------------------|
| í -K1 | MNP extended services enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP - STREAM/BLOCK MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the transfer mode for MNP link |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \L0 | Stream mode for MNP enabled |
|--------------+---------------------------------------------|
| \L1 | Block mode for MNP enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - FALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Allows MNP10 to fall back to speeds slower |
| | than 4800bps |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -Q0 | MNP10 at 2400 and 1200bps disabled |
|--------------+---------------------------------------------|
| -Q1 | MNP10 at 2400 and 1200bps enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - LINK NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the speed at which MNP10 link |
| | negotiation will occur |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í *H0 | Link will be negotiated at highest possible |
| | speed |
|--------------+---------------------------------------------|
| *H1 | Link will be negotiated at 1200bps |
|--------------+---------------------------------------------|
| *H2 | Link will be negotiated at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - POWER LEVEL ADJUST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] )Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls automatic transmit power level |
| | adjustment during MNP 10 link negotiation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í )M0 | Power level adjustment disabled |
|--------------+---------------------------------------------|
| )M1 | Power level adjustment enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports OK |
|--------------+---------------------------------------------|
| I6 | Reports modem data pump model and internal |
| | code revision |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S16=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-125 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls loopback tests: analog, digital, |
| | remote digital, and self tests |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | í 0 | Local analog loopback not in progress |
| | | |
| | 1 | Local analog loopback in progress |
|------+-------+---------------------------------------------|
| 1 | í 0 | Not used |
|------+-------+---------------------------------------------|
| 2 | í 0 | Local digital loopback not in progress |
| | | |
| | 1 | Local digital loopback in progress |
|------+-------+---------------------------------------------|
| 3 | í 0 | Modem not in remote digital loopback |
| | | |
| | 1 | Remote digital loopback in progress |
|------+-------+---------------------------------------------|
| 4 | í 0 | Remote digital loopback not requested |
| | | |
| | 1 | Remote digital loopback requested |
|------+-------+---------------------------------------------|
| 5 | í 0 | Remote digital loopback w/ self-test not in |
| | | progress |
| | 1 | |
| | | Remote digital loopback w/ self-test in |
| | | progress |
|------+-------+---------------------------------------------|
| 6 | í 0 | Local analog loopback w/ self-test not in |
| | | progress |
| | 1 | |
| | | Local analog loopback w/ self-test in |
| | | progress |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODE - PTT |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %TTn [cmds] |
|--------------+---------------------------------------------|
| Description: | Send PTT test signals for a line tests |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - FAX |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S92=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 10 |
|--------------+---------------------------------------------|
| Range: | 0-15 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in fax mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - LEASED-LINE |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S99=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 10 |
|--------------+---------------------------------------------|
| Range: | 0-15 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission over |
| | leased-lines |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - PSTN |
|------------------------------------------------------------|
| Type | Register |
|-------------+----------------------------------------------|
| Format | AT [cmds] S91=n [cmds] |
|-------------+----------------------------------------------|
| Default | 10 |
|-------------+----------------------------------------------|
| Range | 0-15 |
|-------------+----------------------------------------------|
| Unit | -1 dBm |
|-------------+----------------------------------------------|
| Description | Sets the signal level for transmission over |
| | PSTN |
+------------------------------------------------------------+
V.25bis COMMAND SET
+------------------------------------------------------------+
| CONNECT INCOMING CALLS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | CIC |
|--------------+---------------------------------------------|
| Description: | Instructs the modem to answer an incoming |
| | call; if no call is currently incoming, a |
| | result of INV will be returned. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALL REQUESTED NUMBER AND IDENTIFICATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | CRI<#> |
|--------------+---------------------------------------------|
| Description: | Adds dial string and identifier into |
| | memory. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALL REQUESTED NUMBER |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | CRN<#> |
|--------------+---------------------------------------------|
| Description: | Dials the number given; it will ignore |
| | spaces and hyphens in the string; if the |
| | string is more than fifty characters long, |
| | a result of INV will be returned. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALL REQUEST WITH ADDRESS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | CRSn |
|--------------+---------------------------------------------|
| Description: | Dials the number stored in memory register |
| | n |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISREGARD INCOMING CALL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | DIC |
|--------------+---------------------------------------------|
| Description: | Instructs the modem to ignore the incoming |
| | call, if the modem is set to automatically |
| | answer; if no call is currently incoming, a |
| | result of INV will be returned. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PROGRAM NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | PRNn or PRN |
|--------------+---------------------------------------------|
| Description: | Stores a phone number in memory address n. |
| | If the second form of this command is |
| | issued (i.e. with no string to store), it |
| | will clear memory address n. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REQUEST LIST OF DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | RLD |
|--------------+---------------------------------------------|
| Description: | Requests the list of delayed numbers from |
| | the modem; this is a list of numbers that |
| | the modem attempted to call and failed, and |
| | is not allowed to call again until a set |
| | amount of time has elapsed; this is usually |
| | to prevent repeated dialing of a number |
| | (which could indicate an attempted security |
| | breach). |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REQUEST LIST OF FORBIDDEN NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | RLF |
|--------------+---------------------------------------------|
| Description: | Requests the list of forbidden numbers from |
| | the modem; the modem is unable to dial |
| | numbers on this list until its power has |
| | been cycled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REQUEST LISTED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | RLI |
|--------------+---------------------------------------------|
| Description: | The modem will return VAL message. |
+------------------------------------------------------------+
V.25BIS COMMAND SET RESULT CODES
+------------------------------------------------------------+
| CALL FAILURE INDICATOR |
|------------------------------------------------------------|
| Type: | Response |
|-------------------+----------------------------------------|
| Format: | CFIxx |
|-------------------+----------------------------------------|
| Description: | Indicates that the attempt to connect |
| | failed |
|------------------------------------------------------------|
| Response | Name | Description |
|------------+-----------+-----------------------------------|
| CFIAB | Abort | The call was aborted because |
| | | either no dialtone was detected |
| | | or a character was received from |
| | | the host computer. |
|------------+-----------+-----------------------------------|
| CFICB | DCE Busy | An incoming call was detected |
| | | after the dialing command was |
| | | issued. |
|------------+-----------+-----------------------------------|
| CFIET | Engaged | A busy signal was detected. |
| | Tone | |
|------------+-----------+-----------------------------------|
| CFIFC | Forbidden | The number given is on the |
| | Call | forbidden list. |
|------------+-----------+-----------------------------------|
| CFINS | Not | The memory address given did not |
| | Stored | contain a valid telephone number. |
|------------+-----------+-----------------------------------|
| CFINT | No Tone | The remote party did not issue a |
| | | response tone. |
|------------+-----------+-----------------------------------|
| CFIRT | Ring Tone | A responding tone was detected, |
| | | but the call timed out before it |
| | | was completed. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECTION |
|------------------------------------------------------------|
| Type: | Response |
|--------------+---------------------------------------------|
| Format: | CNX |
|--------------+---------------------------------------------|
| Description: | A connection has been successfully |
| | established |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DELAYED CALL |
|------------------------------------------------------------|
| Type: | Response |
|--------------+---------------------------------------------|
| Format: | DLCn |
|--------------+---------------------------------------------|
| Description: | The telephone number given is on the |
| | delayed call list; the call cannot be |
| | completed until n minutes elapse. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INCOMING CALL |
|------------------------------------------------------------|
| Type: | Response |
|--------------+---------------------------------------------|
| Format: | INC |
|--------------+---------------------------------------------|
| Description: | An incoming call has been detected |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INVALID |
|------------------------------------------------------------|
| Type: | Response |
|--------------+---------------------------------------------|
| Format: | INV |
|--------------+---------------------------------------------|
| Description: | The modem was issued an improper command |
+------------------------------------------------------------+
+------------------------------------------------------------+
| VALID |
|------------------------------------------------------------|
| Type: | Response |
|--------------+---------------------------------------------|
| Format: | VAL |
|--------------+---------------------------------------------|
| Description: | The command issued is valid and is being |
| | executed |