TEXT View Source
# EXP COMPUTER, INC.
1414CL
Modem Type Data (synchronous/asynchronous)/Fax
Maximum Data Rate 14.4Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
V1468
Proprietary AT Command Set
+------------------------------------------------------------+
| ACCEPT AUTO-RELIABLE MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \U |
|--------------+---------------------------------------------|
| Example: | AT \U<CR> |
|--------------+---------------------------------------------|
| Description: | Accepts remote modem’s request for reliable |
| | link. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO FALL FORWARD/FALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Gn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT %G0 &W <CR> |
|--------------+---------------------------------------------|
| Description: | Selects auto fallback. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » %G0 | Fallback disabled. |
|--------------+---------------------------------------------|
| %G1 | Fallback enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RELIABLE FALLBACK CHARACTER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %An [cmds] |
|--------------+---------------------------------------------|
| Example: | AT%A13<CR> |
|--------------+---------------------------------------------|
| Default: | 13 |
|--------------+---------------------------------------------|
| Range: | 0-127 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used as the |
| | auto-reliable fallback character. %A0 will |
| | disable this function. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RELIABLE TIME BUFFER CONFIGURATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Cn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \C1 &W<CR> |
|--------------+---------------------------------------------|
| Description: | Controls the handling of incoming data |
| | during auto-reliable time period. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » \CO | Data is discarded. |
|--------------+---------------------------------------------|
| \C1 | Data is buffered. |
|--------------+---------------------------------------------|
| \C2 | Data is discarded, sets to normal mode and |
| | sends auto-reliable character to serial |
| | port. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RETRAIN |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Example: | AT %E0 <CR> |
|--------------+---------------------------------------------|
| Description: | Selects auto-retrain mode. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » %E0 | Auto-retrain disabled. |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BAUD RATE ADJUST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Jn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT %L3 %B14 \J0<CR> |
|--------------+---------------------------------------------|
| Description: | Allows baud rate to follow serial port |
| | speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » \J0 | Baud rate adjust disabled. |
|--------------+---------------------------------------------|
| \J1 | Baud rate adjust enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S14 |
|------------------------------------------------------------|
| Format | AT [cmds] S14? [cmds] |
|-----------------+------------------------------------------|
| Example: | ATS14?<CR> |
|-----------------+------------------------------------------|
| Default: | Read only |
|-----------------+------------------------------------------|
| Range: | 0-174 |
|-----------------+------------------------------------------|
| Unit: | Bit-mapped |
|-----------------+------------------------------------------|
| Description: | Displays echo, result codes, result code |
| | display, dial mode, and answer/originate |
| | mode. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+------------+------------------------------------|
| 0 | 0 | Not used. |
|----------+------------+------------------------------------|
| 1 | 0 | Command echo disabled. |
| | | |
| | 1 | Command echo enabled. |
|----------+------------+------------------------------------|
| 2 | 0 | Result codes enabled. |
| | | |
| | 1 | Result codes disabled. |
|----------+------------+------------------------------------|
| 3 | 0 | Display result codes in numeric |
| | | format. |
| | 1 | |
| | | Display result codes in verbose |
| | | format. |
|----------+------------+------------------------------------|
| 4 | 0 | Not used. |
|----------+------------+------------------------------------|
| 5 | 0 | Tone dial enabled. |
| | | |
| | 1 | Pulse dial enabled. |
|----------+------------+------------------------------------|
| 6 | 0 | Not used. |
|----------+------------+------------------------------------|
| 7 | 0 | Answer mode enabled. |
| | | |
| | 1 | Originate mode enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S21 |
|------------------------------------------------------------|
| Format | AT [cmds] S21? [cmds] |
|----------------+-------------------------------------------|
| Example: | ATS21?<CR> |
|----------------+-------------------------------------------|
| Default: | Read only |
|----------------+-------------------------------------------|
| Range: | 0 - 253 |
|----------------+-------------------------------------------|
| Unit: | Bit-mapped |
|----------------+-------------------------------------------|
| Description: | Displays jack type, CTS signal, low DTR |
| | action, DCD signal, DSR signal, and the |
| | Long Space Disconnect function. |
|------------------------------------------------------------|
| Bit | Value | Function |
|----------+-------+-----------------------------------------|
| 0 | 0 | Selects RJ-11, RJ-41S, or RJ45S jack. |
| | | |
| | 1 | Selects RJ-12 or RJ-13 jack. |
|----------+-------+-----------------------------------------|
| 1 | 0 | Not used. |
|----------+-------+-----------------------------------------|
| 2 | 0 | CTS follows RTS. |
| | | |
| | 1 | CTS forced high. |
|----------+-------+-----------------------------------------|
| 4, 3 | 00 | DTR signal ignored. |
| | | |
| | 01 | Modem goes to command mode on low DTR. |
| | | |
| | 10 | Modem disconnects on low DTR. |
| | | Auto-Answer is disabled. |
| | 11 | |
| | | Modem is initialized on low DTR. |
|----------+-------+-----------------------------------------|
| 5 | 0 | DCD forced high. |
| | | |
| | 1 | DCD normal. |
|----------+-------+-----------------------------------------|
| 6 | 0 | DSR forced high. |
| | | |
| | 1 | DSR normal. |
|----------+-------+-----------------------------------------|
| 7 | 0 | Long Space Disconnect function |
| | | disabled. |
| | 1 | |
| | | Long Space Disconnect function enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S22 |
|------------------------------------------------------------|
| Format | AT [cmds] S22? [cmds] |
|----------------+-------------------------------------------|
| Example: | ATS22?<CR> |
|----------------+-------------------------------------------|
| Default: | Read only |
|----------------+-------------------------------------------|
| Range: | 0 - 255 |
|----------------+-------------------------------------------|
| Unit: | Bit-mapped |
|----------------+-------------------------------------------|
| Description: | Displays volume and speaker settings, |
| | result codes, and make/break pulse ratio. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+-------+----------------------------------------|
| 1, 0 | 00 | Not used. |
| | | |
| | 01 | Low volume setting. |
| | | |
| | 10 | Medium volume setting |
| | | |
| | 11 | Highest volume setting. |
|-----------+-------+----------------------------------------|
| 3, 2 | 00 | Speaker disabled. |
| | | |
| | 01 | Speaker enabled until carrier signal |
| | | detected |
| | 10 | |
| | | Speaker enabled. |
| | 11 | |
| | | Speaker enabled following dialing, |
| | | then disabled after carrier signal |
| | | detected. |
|-----------+-------+----------------------------------------|
| 6, 5 ,4 | 000 | Busy and dialtone detection disabled, |
| | | result codes 0-4 enabled. |
| | 100 | |
| | | Busy and dialtone detection disabled, |
| | 101 | result codes 0-5, 10 enabled. |
| | | |
| | 110 | Busy tone detection disabled, dialtone |
| | | detection enabled, result codes 0-6, |
| | 111 | 10 enabled. |
| | | |
| | | Busy tone detection enabled, dialtone |
| | | detection disabled, result codes 0-5, |
| | | 7, 10 enabled. |
| | | |
| | | Busy and dialtone detection enabled, |
| | | result codes 0-7, 10 enabled. |
|-----------+-------+----------------------------------------|
| 7 | 0 | Pulse dialing at 39/61ms at 10pps. |
| | | |
| | 1 | Pulse dialing at 33/67ms at 10pps. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S23 |
|------------------------------------------------------------|
| Format | AT [cmds] S23? [cmds] |
|-----------------+------------------------------------------|
| Example: | ATS23?<CR> |
|-----------------+------------------------------------------|
| Default: | Read only |
|-----------------+------------------------------------------|
| Range: | 0-255 |
|-----------------+------------------------------------------|
| Unit: | Bit-mapped |
|-----------------+------------------------------------------|
| Description: | Displays remote digital loopback, |
| | controls DTE rate and parity, and sets |
| | guard tone. |
|------------------------------------------------------------|
| Bit | Value | Function |
|------------+-------+---------------------------------------|
| 0 | 0 | Remote digital loopback denied. |
| | | |
| | 1 | Remote digital loopback allowed. |
|------------+-------+---------------------------------------|
| 3, 2, 1 | 000 | Sets serial port speed to 0-300bps. |
| | | |
| | 001 | Sets serial port speed to 1200bps. |
| | | |
| | 010 | Sets serial port speed to 2400bps. |
| | | |
| | 011 | Sets serial port speed to 4800bps. |
| | | |
| | 100 | Sets serial port speed to 7200bps. |
| | | |
| | 101 | Sets serial port speed to 9600bps. |
| | | |
| | 110 | Sets serial port speed to 19.2Kbps. |
| | | |
| | 111 | Sets serial port speed to 38.4Kbps. |
|------------+-------+---------------------------------------|
| 5,4 | 00 | Parity even. |
| | | |
| | 01 | No Parity. |
| | | |
| | 10 | Parity odd. |
| | | |
| | 11 | Mark. |
|------------+-------+---------------------------------------|
| 7, 6 | 00 | Guard tone disabled. |
| | | |
| | 01 | Guard tone disabled. |
| | | |
| | 10 | Guard tone 1800Hz enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S27 |
|------------------------------------------------------------|
| Format | AT [cmds] S27? [cmds] |
|----------------+-------------------------------------------|
| Example: | AT S27? <CR> |
|----------------+-------------------------------------------|
| Default: | Read only |
|----------------+-------------------------------------------|
| Range: | 0 - 127 |
|----------------+-------------------------------------------|
| Unit: | Bit-mapped |
|----------------+-------------------------------------------|
| Description: | Displays synchronous/asynchronous mode, |
| | Line type, internal clock, and ITU-T/Bell |
| | modes. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+----------+-------------------------------------|
| 3, 1, 0 | 000 | Asynchronous mode, serial port |
| | | speed follows connect speed. |
| | 001 | |
| | | Asynchronous command mode and |
| | 010 | synchronous connect mode. |
| | | |
| | 011 | Asynchronous command mode and |
| | | synchronous connect mode, DTR |
| | 100 | dialing enabled. |
| | | |
| | | Asynchronous command mode on low |
| | | DTR, synchronous connect mode on |
| | | high DTR. |
| | | |
| | | Hayes AutoSync™ mode - serial port |
| | | locked at 9600bps. |
|-----------+----------+-------------------------------------|
| 2 | 0 | Dial up line. |
| | | |
| | 1 | Leased line. |
|-----------+----------+-------------------------------------|
| 5, 4 | 00 | Internal DTE transmit clock source. |
| | | |
| | 01 | External DTE transmit clock source. |
| | | |
| | 10 | Slave DTE transmit clock source. |
|-----------+----------+-------------------------------------|
| 6 | 0 | CCITT mode. |
| | | |
| | 1 | Bell mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Bn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \B3 &W<CR> |
|--------------+---------------------------------------------|
| Range: | 0-9 |
|--------------+---------------------------------------------|
| Unit: | .1 second |
|--------------+---------------------------------------------|
| Description: | Sends break to modem. |
+------------------------------------------------------------+
+----------------------------------------------------------------+
| BREAK TYPE |
|----------------------------------------------------------------|
|Type: |Configuration |
|------------------+---------------------------------------------|
|Format: |AT [cmds] \Kn [cmds] |
|------------------+---------------------------------------------|
|Example: |AT \K1 <CR> |
|------------------+---------------------------------------------|
|Description: |Configures action of break signal. |
|----------------------------------------------------------------|
| Command |Break from DTE | Break from | Modem | Break from |
| | | DTE |receives \B |remote modem|
| |Reliable/Normal| | | |
| | mode |Direct mode | | |
|---------+---------------+------------+------------+------------|
| \K0 |Enter command |Send break |Buffers |Buffers |
| |mode, do not |to remote |cleared and |cleared and |
| |send break to |modem |break sent |break sent |
| |remote modem. |immediately,|to remote |to DTE. |
| | |then enter |modem. | |
| | |command | | |
| | |mode. | | |
|---------+---------------+------------+------------+------------|
| \K1 |Buffers cleared|Send break |Buffers |Buffers |
| |and break sent |to remote |cleared and |cleared and |
| |to remote |modem |break sent |break sent |
| |modem. |immediately.|to remote |to DTE. |
| | | |modem. | |
|---------+---------------+------------+------------+------------|
| \K2 |Enter command |Send break |Send break |Send break |
| |mode, do not |to remote |to remote |to DTE |
| |send break to |modem |modem |immediately.|
| |remote modem. |immediately,|immediately.| |
| | |then enter | | |
| | |command | | |
| | |mode. | | |
|---------+---------------+------------+------------+------------|
| \K3 |Send break to |Send break |Send break |Send break |
| |remote modem |to remote |to remote |to DTE |
| |immediately. |modem |modem |immediately.|
| | |immediately.|immediately.| |
|---------+---------------+------------+------------+------------|
| \K4 |Enter command |Send break |Send break |Break sent |
| |mode, do not |to remote |to remote |with |
| |send break to |modem |modem with |received |
| |remote modem. |immediately,|transmitted |data to the |
| | |then enter |data. |DTE. |
| | |command | | |
| | |mode. | | |
|---------+---------------+------------+------------+------------|
|» \K5 |Send break with|Send break |Send break |Break sent |
| |transmitted |to remote |to remote |with |
| |data. |modem |modem with |received |
| | |immediately.|transmitted |data to the |
| | | |data. |DTE. |
+----------------------------------------------------------------+
+------------------------------------------------------------+
| BUFFER CONTROL |
|------------------------------------------------------------|
| Type: | Confiuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Kn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT K1 *L2 #E1<CR> |
|--------------+---------------------------------------------|
| Description: | Selects SRAM for use in Fax mode. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| K0 | SRAM buffer disabled. |
|--------------+---------------------------------------------|
| » K1 | SRAM buffer enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLING TONE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Cn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT -C0 &W<CR> |
|--------------+---------------------------------------------|
| Description: | Controls whether the DTE will allow the |
| | modem to send a 1300Hz calling tone when |
| | originating. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » -C0 | Disable calling tone. |
|--------------+---------------------------------------------|
| -C1 | Enable calling tone. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT *EC0 %C1 *AP0<CR> |
|--------------+---------------------------------------------|
| Description: | Selects data compression. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled. |
|--------------+---------------------------------------------|
| » %C1 | Data compression enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \N1 DT555-1212<CR> |
|--------------+---------------------------------------------|
| Description: | Sets connect mode. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode. |
|--------------+---------------------------------------------|
| \N1 | Direct mode. |
|--------------+---------------------------------------------|
| \N2 | MNP reliable mode. |
|--------------+---------------------------------------------|
| » \N3 | V.42 auto-reliable mode. |
|--------------+---------------------------------------------|
| \N4 | V.42 reliable mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONVERT TO RELIABLE MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Y [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \Y<CR> |
|--------------+---------------------------------------------|
| Description: | Initiates reliable mode link. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Gn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT G1 &K3<CR> |
|--------------+---------------------------------------------|
| Description: | Selects modem port flow control. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » \G0 | Flow control disabled. |
|--------------+---------------------------------------------|
| \G1 | Flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Qn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \Q0 A <CR> |
|--------------+---------------------------------------------|
| Description: | Sets type of flow control used by modem. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \Q0 | Flow control disabled. |
|--------------+---------------------------------------------|
| \Q1 | XON/XOFF flow control enabled. |
|--------------+---------------------------------------------|
| \Q2 | CTS flow control to DTE enabled. |
|--------------+---------------------------------------------|
| » \Q3 | RTS/CTS flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Tn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT\T20<CR> |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-90 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S90=n [cmds] |
|--------------+---------------------------------------------|
| Example: | ATS90=20<CR> |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Sets the length of time that the modem does |
| | not receive information before it |
| | disconnects. S90=0 will disable. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MAXIMUM BLOCK SIZE FOR TRANSMISSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \An [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \A3 &MB28800<CR> |
|--------------+---------------------------------------------|
| Description: | Sets the maximum transmittable block size. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \A0 | Maximum MNP block size is 64 characters. |
|--------------+---------------------------------------------|
| \A1 | Maximum MNP block size is 128 characters. |
|--------------+---------------------------------------------|
| \A2 | Maximum MNP block size is 192 characters. |
|--------------+---------------------------------------------|
| » \A3 | Maximum MNP block size is 256 characters. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ON-LINE IN RELIABLE MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \O [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \O <CR> |
|--------------+---------------------------------------------|
| Description: | Returns to on-line and requests reliable |
| | mode connection. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT SIGNAL QUALITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Q [cmds] |
|--------------+---------------------------------------------|
| Example: | AT %Q<CR> |
|--------------+---------------------------------------------|
| Description: | Reports signal quality. If the value is |
| | greater than 7, the modem will retrain. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESULT CODES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Vn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \V0 Q0 <CR> |
|--------------+---------------------------------------------|
| Description: | Controls result codes the modem will |
| | display. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \V0 | Basic result code enabled. |
|--------------+---------------------------------------------|
| \V1 | Modified MNP result code enabled. |
|--------------+---------------------------------------------|
| » \V2 | Extended V.42 result code enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Example: | AT I1 &W<CR> |
|--------------+---------------------------------------------|
| Description: | Displays modem properties. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code. |
|--------------+---------------------------------------------|
| I1 | Reports firmware version number. |
|--------------+---------------------------------------------|
| I2 | Reports ROM checksum. |
|--------------+---------------------------------------------|
| I3 | Reports device set name. |
|--------------+---------------------------------------------|
| I4 | Reports current configuration (see rows |
| | below, default is 31). |
|------------------------------------------------------------|
| | Bit | Value | Meaning |
|---------------+-----+-------+------------------------------|
| | 0 | 0 | Hayes escape sequence. |
| | | | |
| | | » 1 | TIES escape sequence. |
|---------------+-----+-------+------------------------------|
| | 1 | 0 | No error corection firmware. |
| | | | |
| | | » 1 | Error corection firmware. |
|---------------+-----+-------+------------------------------|
| | 2 | 0 | Serial host interface. |
| | | | |
| | | » 1 | Parallel host interface. |
|---------------+-----+-------+------------------------------|
| | 3 | 0 | No external static RAM |
| | | | present. |
| | | » 1 | |
| | | | External static RAM present. |
|---------------+-----+-------+------------------------------|
| | 4 | 0 | 8K x 8 static RAM present. |
| | | | |
| | | » 1 | 32K x 8 static RAM present. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RETURN TO RELIABLE MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Z [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \Z <CR> |
|--------------+---------------------------------------------|
| Description: | Ends reliable mode link, initiate return to |
| | normal mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Format | AT [cmds] S16? [cmds] |
|---------------+--------------------------------------------|
| Example: | ATS16?<CR> |
|---------------+--------------------------------------------|
| Default: | Ready-only |
|---------------+--------------------------------------------|
| Range: | 0-125 |
|---------------+--------------------------------------------|
| Unit: | Bit-mapped |
|---------------+--------------------------------------------|
| Description: | Displays loopback tests, analog, digital, |
| | remote digital, and self tests. |
|------------------------------------------------------------|
| Bit | Value | Function |
|---------+-------+------------------------------------------|
| 0 | 0 | Local analog loopback not in progress. |
| | | |
| | 1 | Local analog loopback in progress. |
|---------+-------+------------------------------------------|
| 1 | 0 | Not used. |
|---------+-------+------------------------------------------|
| 2 | 0 | Local digital loopback not in progress. |
| | | |
| | 1 | Local digital loopback in progress. |
|---------+-------+------------------------------------------|
| 3 | 0 | Modem not in remote digital loopback. |
| | | |
| | 1 | Remote digital loopback in progress. |
|---------+-------+------------------------------------------|
| 4 | 0 | Remote digital loopback not requested. |
| | | |
| | 1 | Remote digital loopback requested. |
|---------+-------+------------------------------------------|
| 5 | 0 | Remote digital loopback w/ self-test not |
| | | in progress. |
| | 1 | |
| | | Remote digital loopback w/ self-test in |
| | | progress. |
|---------+-------+------------------------------------------|
| 6 | 0 | Local analog loopback w/ self-test not |
| | | in progress. |
| | 1 | |
| | | Local analog loopback w/ self-test in |
| | | progress. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.42 DETECTION PHASE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Jn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT -J1 &W<CR> |
|--------------+---------------------------------------------|
| Description: | Controls V.42 detection. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -J0 | V.42 detection disabled. |
|--------------+---------------------------------------------|
| » -J1 | V.42 detection enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.42bis COMPRESSION CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] "Hn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT "H3 &W<CR> |
|--------------+---------------------------------------------|
| Description: | Controls V.42bis data compression. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| "H0 | V.42bis disabled. |
|--------------+---------------------------------------------|
| "H1 | V.42bis when transmitting enabled. |
|--------------+---------------------------------------------|
| "H2 | V.42bis when receiving enabled. |
|--------------+---------------------------------------------|
| » "H3 | V.42bis when transmitting/receiving |
| | enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.42bis MAXIMUM STRING LENGTH |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] "On [cmds] |
|--------------+---------------------------------------------|
| Example: | AT "O16 <CR> |
|--------------+---------------------------------------------|
| Default: | 16 |
|--------------+---------------------------------------------|
| Range: | 6 - 250 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Selects string size for V.42bis |
| | compression. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| XON/XOFF PASS-THROUGH |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Xn [cmds] |
|--------------+---------------------------------------------|
| Example: | AT \X7 O<CR> |
|--------------+---------------------------------------------|
| Description: | Selects whether XON/XOFF signals are sent |
| | to remote modem. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| » \X0 | XON/XOFF signals trapped by local modem. |
|--------------+---------------------------------------------|
| \X1 | XON/XOFF passed through local modem. |