TEXT View Source
# OLICOM, INC.
OC-7111
Card Type Fax, Modem (asynchronous)
Chip Set Unidentified
Maximum Data Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis, V.34
Rockwell V.FC
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Protocol
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
V1942
+------------------------------------------------------------+
| MISCELLANEOUS TECHNICAL NOTES |
|------------------------------------------------------------|
| Note: Due to country specific parameters, S-register |
| settings are unidentified. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTOSYNC™ |
|------------------------------------------------------------|
| Format | AT [cmds] S19=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-30 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Sets options for Hayes AutoSync™ functions. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Not used. |
|------+-------+---------------------------------------------|
| 1 | 0 | BSC enabled. |
| | | |
| | 1 | HDLC enabled. |
|------+-------+---------------------------------------------|
| 2 | 0 | HDLC address detection disabled. |
| | | |
| | 1 | HDLC address detection enabled. |
|------+-------+---------------------------------------------|
| 3 | 0 | NRZI bit encoding enabled. |
| | | |
| | 1 | NRZ2 bit encoding enabled. |
|------+-------+---------------------------------------------|
| 4 | 0 | Mark idle enabled. |
| | | |
| | 1 | Flag or sync idle enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC HDLC ADDRESS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S20=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Sets the HDLC address/BSC character |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall-forward |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í %E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled |
|--------------+---------------------------------------------|
| %E2 | Auto-fallback/fall-forward enabled |
|--------------+---------------------------------------------|
| %E3 | Auto-retrain enabled with fast hang-up |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT MAPPED REGISTERS |
|------------------------------------------------------------|
| Register | Default |
|----------------------------+-------------------------------|
| S14 | Unidentified |
|----------------------------+-------------------------------|
| S21 | Unidentified |
|----------------------------+-------------------------------|
| S22 | Unidentified |
|----------------------------+-------------------------------|
| S23 | Unidentified |
|----------------------------+-------------------------------|
| S27 | Unidentified |
|----------------------------+-------------------------------|
| S28 | Unidentified |
|----------------------------+-------------------------------|
| S31 | Unidentified |
|----------------------------+-------------------------------|
| S40 | Unidentified |
|----------------------------+-------------------------------|
| S41 | Unidentified |
|----------------------------+-------------------------------|
| S201 | Unidentified |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK SEND |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Bn [cmds] |
|--------------+---------------------------------------------|
| Default: | 3 |
|--------------+---------------------------------------------|
| Range: | 1-9 |
|--------------+---------------------------------------------|
| Unit: | .1 second |
|--------------+---------------------------------------------|
| Description: | Sends break to modem |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|---------------------+--------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|---------------------+--------------------------------------|
| Description: | Configures action of break signal |
|------------------------------------------------------------|
| Command | Break from | Modem receives | Break received |
| | DTE | \B | from remote |
| | | | modem |
|-----------+--------------+----------------+----------------|
| \K0 | Online | Break sent to | Buffers |
| | command mode | remote modem | cleared, break |
| | enabled, | and buffered | sent to DTE |
| | send no | cleared | |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| \K1 | Break sent | Break sent to | Buffers |
| | to remote | remote modem | cleared, break |
| | modem and | and buffered | sent to DTE |
| | buffered | cleared | |
| | cleared | | |
|-----------+--------------+----------------+----------------|
| \K2 | Online | Send break to | Break sent |
| | command mode | remote modem | immediately to |
| | enabled, | immediately | DTE |
| | send no | | |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| \K3 | Send break | Send break to | Break sent |
| | to remote | remote modem | immediately to |
| | modem | immediately | DTE |
| | immediately | | |
|-----------+--------------+----------------+----------------|
| \K4 | Online | Send break | Break sent |
| | command mode | with | with received |
| | enabled, | transmitted | data to the |
| | send no | data | DTE |
| | break to | | |
| | remote modem | | |
|-----------+--------------+----------------+----------------|
| í \K5 | Send break | Send break | Break sent |
| | with | with | with received |
| | transmitted | transmitted | data to the |
| | data | data | DTE |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COUNTRY CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NCnn [cmds] |
|--------------+---------------------------------------------|
| Description: | Select a country code from NVRAM (nn=00-08) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DJ | Link will be negotiated at 1200bps for |
| | current call only |
|--------------+---------------------------------------------|
| DK | Power level adjustment enabled for current |
| | call only |
|--------------+---------------------------------------------|
| DL | Re-dial last number |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled/Pulse dialing disabled |
|--------------+---------------------------------------------|
| DR | Accepted but not used. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| D; | Modem returned to command state after |
| | dialing. The semicolon can only be placed |
| | at the end of the dial command. |
|--------------+---------------------------------------------|
| D^ | Calling tone enabled/disabled for current |
| | dialing attempt |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIALING CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Zn [cmds] |
|--------------+---------------------------------------------|
| Description: | Select the dial code for pulse dialing |
|------------------------------------------------------------|
| Command | Function |
|---------------------------+--------------------------------|
| í *Z0 | Use dial code 0 |
|---------------------------+--------------------------------|
| *Z1 | Use dial code 1 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *B [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays delayed numbers list |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *D [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays delayed numbers list |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMPRESSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Cn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects data compression |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %C0 | Data compression disabled |
|--------------+---------------------------------------------|
| %C1 | MNP5 enabled |
|--------------+---------------------------------------------|
| %C2 | V.42bis enabled |
|--------------+---------------------------------------------|
| í %C3 | MNP5 and V.42bis enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will operate in |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Normal mode enabled |
|--------------+---------------------------------------------|
| \N1 | Direct mode enabled |
|--------------+---------------------------------------------|
| \N2 | MNP reliable mode enabled |
|--------------+---------------------------------------------|
| í \N3 | Auto-reliable mode enabled |
|--------------+---------------------------------------------|
| \N4 | V.42 reliable mode enabled |
|--------------+---------------------------------------------|
| \N5 | MNP auto-reliable mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLASH DIAL MODIFIER TIME |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S29=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Time the modem will go on-hook upon |
| | receiving the ! dial modifier in dial |
| | string. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Gn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects modem port flow control |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \G0 | Flow control disabled |
|--------------+---------------------------------------------|
| \G1 | Flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XOFF |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S33=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 19 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XOFF |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL CHARACTER - XON |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S32=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 17 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | ASCII |
|--------------+---------------------------------------------|
| Description: | Sets the character used to represent XON |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL LEVEL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %L [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates the |
| | received line signal level |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE SIGNAL QUALITY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %Q [cmds] |
|--------------+---------------------------------------------|
| Description: | Returns a value which indicates line signal |
| | quality |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Jn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets operation of serial port speed |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \J0 | Serial speed locked |
|--------------+---------------------------------------------|
| \J1 | Serial speed follows connect speed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MAXIMUM BLOCK SIZE FOR TRANSMISSION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \An [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the maximum transmittable block size |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \A0 | MNP block size is 64 characters |
|--------------+---------------------------------------------|
| í \A1 | MNP block size is 128 characters |
|--------------+---------------------------------------------|
| \A2 | MNP block size is 192 characters |
|--------------+---------------------------------------------|
| \A3 | MNP block size is 256 characters |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION SELECTION DISPLAY |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] +MS? [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays modulation, automode, minimum rate |
| | and maximum rate settings |
|------------------------------------------------------------|
| Command | Function |
|-------------------+----------------------------------------|
| +MS=? | Displays supported mode selection |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] +MS=x,y,z,a [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets options for active protocol; the |
| | transfer rates specified by z and a must be |
| | valid for the protocol selected. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| x=0 | V.21 |
|--------------+---------------------------------------------|
| x=1 | V.22 |
|--------------+---------------------------------------------|
| x=2 | V.22bis |
|--------------+---------------------------------------------|
| x=3 | V.23 |
|--------------+---------------------------------------------|
| x=9 | V.32 |
|--------------+---------------------------------------------|
| x=10 | V.32bis |
|--------------+---------------------------------------------|
| x=11 | V.34 |
|--------------+---------------------------------------------|
| x=64 | Bell 103 |
|--------------+---------------------------------------------|
| x=69 | Bell 212A |
|--------------+---------------------------------------------|
| x=74 | V.FC |
|--------------+---------------------------------------------|
| y=0 | Automode disabled |
|--------------+---------------------------------------------|
| y=1 | Auto-detect highest speed enabled |
|--------------+---------------------------------------------|
| z, a=300 | Set minimum or maximum transfer rate at |
| | 300bps, respectively. |
|--------------+---------------------------------------------|
| z, a=1200 | Set minimum or maximum transfer rate at |
| | 1200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=2400 | Set minimum or maximum transfer rate at |
| | 2400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=4800 | Set minimum or maximum transfer rate at |
| | 4800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=7200 | Set minimum or maximum transfer rate at |
| | 7200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=9600 | Set minimum or maximum transfer rate at |
| | 9600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=12000 | Set minimum or maximum transfer rate at |
| | 12000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=14400 | Set minimum or maximum transfer rate at |
| | 14400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=16800 | Set minimum or maximum transfer rate at |
| | 16800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=19200 | Set minimum or maximum transfer rate at |
| | 19200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=21600 | Set minimum or maximum transfer rate at |
| | 21600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=24000 | Set minimum or maximum transfer rate at |
| | 24000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=26400 | Set minimum or maximum transfer rate at |
| | 26400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=28800 | Set minimum or maximum transfer rate at |
| | 28800bps, respectively. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP - EXTENDED SERVICES |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects MNP extended services |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í -K0 | MNP extended services disabled |
|--------------+---------------------------------------------|
| -K1 | MNP extended services enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP - STREAM/BLOCK MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects the transfer mode for MNP link |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í \L0 | Stream mode for MNP enabled |
|--------------+---------------------------------------------|
| \L1 | Block mode for MNP enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - FALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] -Qn [cmds] |
|--------------+---------------------------------------------|
| Description: | Allows MNP10 to fall back to speeds slower |
| | than 4800bps |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| -Q0 | MNP10 at 2400 and 1200bps enabled |
|--------------+---------------------------------------------|
| -Q1 | MNP10 at 2400 and 1200bps disabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - LINK NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Hn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the speed at which MNP10 link |
| | negotiation will occur |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| *H0 | Link will be negotiated at highest possible |
| | speed |
|--------------+---------------------------------------------|
| *H1 | Link will be negotiated at 1200bps |
|--------------+---------------------------------------------|
| *H2 | Link will be negotiated at 4800bps |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MNP10 - POWER LEVEL ADJUST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] )Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls automatic transmit power level |
| | adjustment during MNP 10 link negotiation |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í )M0 | Power level adjustment disabled |
|--------------+---------------------------------------------|
| )M1 | Power level adjustment enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product code |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Calculates and reports ROM checksum |
|--------------+---------------------------------------------|
| I3 | Reports firmware level |
|--------------+---------------------------------------------|
| I5 | Reports country code |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SLEEP TIMER |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format | AT [cmds] S24=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | Unidentified |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Maximum duration of DTE and DCE inactivity |
| | allowed prior to initiating low-power sleep |
| | mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Fn [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays phone number directory |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TEST MODES |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S16=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-125 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Controls loopback tests, analog, digital, |
| | remote digital, and self tests. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Local analog loopback not in progress |
| | | |
| | 1 | Local analog loopback in progress |
|------+-------+---------------------------------------------|
| 1 | 0 | Not used |
|------+-------+---------------------------------------------|
| 2 | 0 | Local digital loopback not in progress |
| | | |
| | 1 | Local digital loopback in progress |
|------+-------+---------------------------------------------|
| 3 | 0 | Modem not in remote digital loopback |
| | | |
| | 1 | Remote digital loopback in progress |
|------+-------+---------------------------------------------|
| 4 | 0 | Remote digital loopback not requested |
| | | |
| | 1 | Remote digital loopback requested |
|------+-------+---------------------------------------------|
| 5 | 0 | Remote digital loopback w/ self-test not in |
| | | progress |
| | 1 | |
| | | Remote digital loopback w/ self-test in |
| | | progress |
|------+-------+---------------------------------------------|
| 6 | 0 | Local analog loopback w/ self-test not in |
| | | progress |
| | 1 | |
| | | Local analog loopback w/ self-test in |
| | | progress |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - CELLULAR |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] @Mn [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-31 |
|--------------+---------------------------------------------|
| Unit: | -1dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in cellular mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - FAX |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S92=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-15 |
|--------------+---------------------------------------------|
| Unit: | -1 dBm |
|--------------+---------------------------------------------|
| Description: | Sets the signal level for transmission |
| | while in fax mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| TRANSMISSION LEVEL - PSTN |
|------------------------------------------------------------|
| Type | Register |
|-------------+----------------------------------------------|
| Format | AT [cmds] S91=n [cmds] |
|-------------+----------------------------------------------|
| Default | Unidentified |
|-------------+----------------------------------------------|
| Range | 0-15 |
|-------------+----------------------------------------------|
| Unit | -1 dBm |
|-------------+----------------------------------------------|
| Description | Sets the signal level for transmission over |
| | switched phone lines |
+------------------------------------------------------------+
+------------------------------------------------------------+
| V.32 - COMPROMISE EQUALIZER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] :En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls V.32 compromise equalizer |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| :E0 | Equalizer disabled |
|--------------+---------------------------------------------|
| í :E1 | Equalizer enabled |