TEXT View Source
# MAXTECH CORPORATION
XPS 288IR (SF-1128HV/R16-PNP)
Card Type Modem, Fax
Chip Set Unidentified
I/O Options Line in, line out, microphone in,
speaker out
Maximum Modem Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Bell 103/212A
Protocol
ITU-T V.21, V.22, V.22bis, V.23, V.32,
V.32bis, V.34
Fax Modulation ITU-T V.17, V.27ter, V.29
Protocol
Error MNP5, V.42, V.42bis
Correction/Compression
Fax Class Class I & II
Data Bus 16-bit ISA
Card Size Half-length, half-height card
IMG IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line out | CN1 | Microphone in | CN3 |
|--------------------------+----------+---------------+------|
| Line in | CN2 | Speaker out | CN4 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED COMMAND SET |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| AT, ‘+++’, A/ |
|------------------------------------------------------------|
| A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &F, &P, &T, &V, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \K, \N |
|------------------------------------------------------------|
| %C, %L, %Q |
|------------------------------------------------------------|
| S Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S21, S22, S23, S24, S25, |
|------------------------------------------------------------|
| S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, |
| S40, S41, S46, S48, S82, S86, S91, S92, |
|------------------------------------------------------------|
| S95 |
|------------------------------------------------------------|
| Special Commands |
|------------------------------------------------------------|
| #BDR, #CID=n, #CID?, #CID=?, #MDL?, #MFR?, #REV?, #TL, |
| #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, |
|------------------------------------------------------------|
| #VRN, #VRX, #VSDB, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, |
| #VTS, #VTX, +MS |
|------------------------------------------------------------|
| |
|------------------------------------------------------------|
| Note: See MHI Help File for full command documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTOSCAN MODE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables/Disables Autoscan mode |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| N0 | Autoscan mode disabled |
|--------------+---------------------------------------------|
| í N1 | Autoscan mode enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Mn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects communications mode |
|--------------+---------------------------------------------|
| Command | Mode |
|--------------+---------------------------------------------|
| í &M0 | Asynchronous mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COMMUNICATIONS MODE (DATA LINK AND FALLBACK) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Q [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures data link options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &Q0 | Set Direct data link only |
|--------------+---------------------------------------------|
| &Q5 | Set V.42 data link with fallback options |
|--------------+---------------------------------------------|
| &Q6 | Set Normal data link only |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures CTS settings |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &R0 | Reserved |
|--------------+---------------------------------------------|
| í &R1 | Enables CTS operation based on flow control |
| | settings |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA SET READY (DSR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Sn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects DSR options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &S0 | DSR forced high |
|--------------+---------------------------------------------|
| í &S1 | DSR is off while in command mode and set on |
| | in on-line mode |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA TERMINAL READY (DTR) |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Dn [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects modem response to DTR |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &D0 | Modem does not respond to DTR |
|--------------+---------------------------------------------|
| &D1 | Modem goes to command mode after DTR goes |
| | is off |
|--------------+---------------------------------------------|
| &D2 | Modem goes to command mode and disconnects |
| | (hangs up) after DTR goes off; Auto-Answer |
| | is disabled. |
|--------------+---------------------------------------------|
| &D3 | Modem is initialized after DTR goes off |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DL | Re-dial last number |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled |
|--------------+---------------------------------------------|
| í DT | Tone dialing enabled/Pulse dialing disabled |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register |
|--------------+---------------------------------------------|
| D"WXY" | Optional method of denoting telephone |
| | numbers. Letters enclosed in quotes are |
| | interpreted as numbers according to the |
| | system found on a telephone keypad. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quite Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &K [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures flow control settings |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &K0 | Flow control disabled |
|--------------+---------------------------------------------|
| &K3 | RTS/CTS hardware flow control enabled |
|--------------+---------------------------------------------|
| &K4 | XON/XOFF software flow control enabled |
|--------------+---------------------------------------------|
| &K5 | Transparent XON/XOFF software flow control |
| | enabled |
|--------------+---------------------------------------------|
| &K6 | RTS/CTS & XON/XOFF flow control enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| GUARD TONE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Gn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables/Disables and configures guard tone |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í &G0 | Guard tone disabled |
|--------------+---------------------------------------------|
| &G1 | Guard tone disabled |
|--------------+---------------------------------------------|
| &G2 | Set guard tone at 1800Hz |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HAYES SMARTMODEM 300 COMPATIBILITY |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Xn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures modem response and blind dialing |
| | capabilities |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| X0 | Sets modem to use Hayes Smartmodem 300 |
| | responses and blind dialing |
|--------------+---------------------------------------------|
| X1 | Sets modem to use Hayes Smartmodem 300 |
| | responses, CONNECT responses, and blind |
| | dialing |
|--------------+---------------------------------------------|
| X2 | Sets modem to use Hayes Smartmodem 300 |
| | responses, CONNECT responses, dial tone |
| | detection, and blind dialing |
|--------------+---------------------------------------------|
| X3 | Sets modem to use Hayes Smartmodem 300 |
| | responses, CONNECT responses, busy |
| | detection, and blind dialing |
|--------------+---------------------------------------------|
| í X4 | Set modem to use all responses, dial tone |
| | detection, and busy signal detection |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Selects line type |
|--------------+---------------------------------------------|
| Command | Line Type |
|--------------+---------------------------------------------|
| í &L0 | Switched line (PSTN/Dial-up) |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports product ID |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests and reports internal memory |
|--------------+---------------------------------------------|
| I3 | Reports firmware ID |
|--------------+---------------------------------------------|
| I4 | Reports reserved ID |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SPEAKER VOLUME |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] Ln [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls speaker volume |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| L0 | Low volume setting |
|--------------+---------------------------------------------|
| í L1 | Low volume setting |
|--------------+---------------------------------------------|
| L2 | Medium volume setting |
|--------------+---------------------------------------------|
| L3 | Highest volume setting |
+------------------------------------------------------------+
Extended AT Commands
+------------------------------------------------------------+
| AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall-forward |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| %E0 | Auto-retrain disabled |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures data link and fallback options |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Set Normal data link only |
|--------------+---------------------------------------------|
| \N1 | Set Direct data link only |
|--------------+---------------------------------------------|
| \N2 | Set V.42 or MNP data link only |
|--------------+---------------------------------------------|
| í \N3 | Set V.42/MNP/Normal data link |
|--------------+---------------------------------------------|
| \N4 | Set V.42 data link only |
|--------------+---------------------------------------------|
| \N5 | Set MNP data link only |
+------------------------------------------------------------+