TEXT View Source
# STOLLMANN GMBH
TA-DD
Card Type ISDN TA
Chip Set Unidentified
Maximum Data Rate 64Kbps x 2
Data Bus External
ISDN Modulation Protocol V.110, 1TR6, DSS1, X.30
IMG IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line out | CN1 | V.24 or | CN4 |
| | | X.21 port | |
| | | 1 | |
|--------------------------+-------------+------------+------|
| DC power | CN2 | Reset | SW1 |
| | | button | |
|--------------------------+-------------+------------+------|
| V.24 or X.21 port 2 | CN3 | | |
|------------------------------------------------------------|
| Note: X.21 functionality is provided by an included |
| adapter cable. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER CONFIGURABLE SETTINGS |
|------------------------------------------------------------|
| Setting | Label | Position |
|-------------------------------------+-------+--------------|
| í Editor debug mode disabled | J3 | Open |
|-------------------------------------+-------+--------------|
| Editor debug mode enabled | J3 | Closed |
|-------------------------------------+-------+--------------|
| í TA will use saved profile | J4 | Open |
|-------------------------------------+-------+--------------|
| TA will use default profile only | J4 | Closed |
|-------------------------------------+-------+--------------|
| í Remote configuration enabled | J6 | Open |
|-------------------------------------+-------+--------------|
| Remote configuration disabled | J6 | Closed |
|-------------------------------------+-------+--------------|
| í Port 1 is in V.24 mode | J9 | Open |
|-------------------------------------+-------+--------------|
| Port 1 is in X.21 mode | J9 | Closed |
|-------------------------------------+-------+--------------|
| í Port 2 is in V.24 mode | J10 | Open |
|-------------------------------------+-------+--------------|
| Port 2 is in X.21 mode | J10 | Closed |
|-------------------------------------+-------+--------------|
| í Port 1 is in DCE mode | J13 | Closed |
|-------------------------------------+-------+--------------|
| Port 1 is in DTE mode | J13 | Open |
|-------------------------------------+-------+--------------|
| í Pin 25 of port 1 is not connected | J13A | Open |
|-------------------------------------+-------+--------------|
| Pin 25 of port 1 is +9V DC | J13A | Closed |
|-------------------------------------+-------+--------------|
| í Port 2 is in DCE mode | J14 | Closed |
|-------------------------------------+-------+--------------|
| Port 2 is in DTE mode | J14 | Open |
|-------------------------------------+-------+--------------|
| í Pin 25 of port 2 is not connected | J14A | Open |
|-------------------------------------+-------+--------------|
| Pin 25 of port 2 is +9V DC | J14A | Closed |
|-------------------------------------+-------+--------------|
| í Pin 1 of port 1 is capacitive | JN1 | Open |
| ground | | |
|-------------------------------------+-------+--------------|
| Pin 1 of port 1 is galvanic ground | JN1 | Closed |
|-------------------------------------+-------+--------------|
| í Pin 1 of port 2 is capacitive | JN2 | Open |
| ground | | |
|-------------------------------------+-------+--------------|
| Pin 1 of port 2 is galvanic ground | JN2 | Closed |
|-------------------------------------+-------+--------------|
| í Factory configured - do not alter | J5 | Unidentified |
|-------------------------------------+-------+--------------|
| í Factory configured - do not alter | J7 | Unidentified |
|-------------------------------------+-------+--------------|
| í Factory configured - do not alter | J8 | Unidentified |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ISDN INTERFACE TYPE |
|------------------------------------------------------------|
| Setting | J11 | J12 |
|------------------+--------------------+--------------------|
| S-interface | Pins 1 & 2 closed | Pins 1 & 2 closed |
|------------------+--------------------+--------------------|
| U-interface | Pins 2 & 3 closed | Pins 2 & 3 closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE TYPE |
|------------------------------------------------------------|
| Setting | J1 | J2 |
|--------------------+-------------------+-------------------|
| Public ISDN | Open | Open |
|--------------------+-------------------+-------------------|
| ISDN PBX | Closed | Open |
|--------------------+-------------------+-------------------|
| ISDN PBX with LLC | Open | Closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAGNOSTIC LED(S) |
|------------------------------------------------------------|
| LED1 Status | Condition |
|-------------------------------------------+----------------|
| On | Power is on |
|-------------------------------------------+----------------|
| Off | Power is off |
|-------------------------------------------+----------------|
| Blinking | ISDN failed |
|-------------------------------------------+----------------|
| LED2 Status | LED3 Status | LED4 Status | Condition |
|--------------+--------------+-------------+----------------|
| Off | Off | Off | Normal |
| | | | operation for |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| On | Off | Off | ISDN |
| | | | connection |
| | | | established on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Alternating | Alternating | Off | Hotline call |
| | | | repetition in |
| | | | progress on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Blinking | Blinking | Off | Hotline call |
| | | | repetition |
| | | | error on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Blinking | Off | Off | Hotline active |
| | | | without |
| | | | connection on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| On | Off | Off | Profile editor |
| | | | in use locally |
| | | | on channel 1 |
|--------------+--------------+-------------+----------------|
| On | On | On | Profile editor |
| | | | password being |
| | | | entered on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| On | Blinking | Blinking | Profile editor |
| | | | in use |
| | | | remotely on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Off | Off | On | Unable to |
| | | | determine |
| | | | correct |
| | | | connection |
| | | | rate on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Off | On | Off | Buffer has |
| | | | overflowed on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| Alternating | Blinking | Alternating | Checksum error |
| | | | has been |
| | | | detected on |
| | | | channel 1 |
|--------------+--------------+-------------+----------------|
| LED5 Status | LED6 Status | LED7 Status | Condition |
|--------------+--------------+-------------+----------------|
| Off | Off | Off | Normal |
| | | | operation for |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| On | Off | Off | ISDN |
| | | | connection |
| | | | established on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Alternating | Alternating | Off | Hotline call |
| | | | repetition in |
| | | | progress on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Blinking | Blinking | Off | Hotline call |
| | | | repetition |
| | | | error on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Blinking | Off | Off | Hotline active |
| | | | without |
| | | | connection on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| On | Off | Off | Profile editor |
| | | | in use locally |
| | | | on channel 2 |
|--------------+--------------+-------------+----------------|
| On | On | On | Profile editor |
| | | | password being |
| | | | entered on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| On | Blinking | Blinking | Profile editor |
| | | | in use |
| | | | remotely on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Off | Off | On | Unable to |
| | | | determine |
| | | | correct |
| | | | connection |
| | | | rate on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Off | On | Off | Buffer has |
| | | | overflowed on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| Alternating | Blinking | Alternating | Checksum error |
| | | | has been |
| | | | detected on |
| | | | channel 2 |
|--------------+--------------+-------------+----------------|
| LED2 | LED3 | LED4 | LED5 | LED6 | LED7 | Condition |
|-------+------+------+-------+------+------+----------------|
| Blink | Off | Off | Blink | Off | Off | TA is |
| | | | | | | resetting |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTO-ANSWER TIME |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S0=n [cmds] |
|--------------+---------------------------------------------|
| Default: | Unidentified |
|--------------+---------------------------------------------|
| Range: | 0-24 |
|--------------+---------------------------------------------|
| Unit: | 5 seconds |
|--------------+---------------------------------------------|
| Description: | Sets the amount of time that will elapse |
| | before the TA will answer an incoming call. |
| | When this value is set to 0 the TA will not |
| | automatically answer calls. A value of 1 |
| | will answer immediately. Values greater |
| | than 1 set the time to (n-1) * 5 seconds. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS SIGNAL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the operation of the Clear to Send |
| | signal. |
|------------------------------------------------------------|
| Command | Function |
|--------------------+---------------------------------------|
| &R0 | CTS follows RTS. |
|--------------------+---------------------------------------|
| &R1 | CTS forced high. |
|--------------------+---------------------------------------|
| &R2 | CTS follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the type of flow control used. |
|------------------------------------------------------------|
| Command | Function |
|------------------+-----------------------------------------|
| &K0 | Flow control disabled. |
|------------------+-----------------------------------------|
| &K3 | CTS/RTS flow control enabled. |
|------------------+-----------------------------------------|
| &K4 | XON/XOFF flow control enabled. |
|------------------+-----------------------------------------|
| &K5 | Flow control disabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESULT CODES |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S15=n [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables caller ID information and extended |
| | result codes. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| S15=0 | Caller ID information and extended result |
| | codes disabled. |
|---------------+--------------------------------------------|
| S15=1 | Caller ID information enabled. |
|---------------+--------------------------------------------|
| S15=3 | Caller ID information and extended result |
| | codes enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| BIT-MAPPED REGISTER S14 |
|------------------------------------------------------------|
| Format: | AT [cmds] S14=n [cmds] |
|----------------+-------------------------------------------|
| Default: | Unidentified |
|----------------+-------------------------------------------|
| Range: | 0-14 |
|----------------+-------------------------------------------|
| Description: | Controls echo mode and result codes. |
|------------------------------------------------------------|
| Bit | Value | Function |
|---------+---------+----------------------------------------|
| 0 | 0 | Not used. |
|------------------------------------------------------------|
| 1 | 0 | Command echo disabled. |
| | | |
| | 1 | Command echo enabled. |
|-------------+-------+--------------------------------------|
| 2 | 0 | Result codes enabled. |
| | | |
| | 1 | Result codes disabled. |
|-------------+-------+--------------------------------------|
| 3 | 0 | Numerical result codes enabled. |
| | | |
| | 1 | Verbose result codes enabled. |
+------------------------------------------------------------+
Proprietary Command Set
+------------------------------------------------------------+
| COMMAND ECHOING |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Jn |
|--------------+---------------------------------------------|
| Description: | Selects whether commands will be echoed |
| | back to the DTE. |
|------------------------------------------------------------|
| Command | Function |
|---------------------+--------------------------------------|
| J0 | Command echoing disabled. |
|---------------------+--------------------------------------|
| í J1 | Command echoing enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECTION SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Hn |
|--------------+---------------------------------------------|
| Description: | Sets the speed of the remote connection. |
|------------------------------------------------------------|
| Command | Function |
|------------------------+-----------------------------------|
| H1 | Set speed to 300bps. |
|------------------------+-----------------------------------|
| H2 | Set speed to 600bps. |
|------------------------+-----------------------------------|
| H3 | Set speed to 1200bps. |
|------------------------+-----------------------------------|
| H4 | Set speed to 2400bps. |
|------------------------+-----------------------------------|
| H5 | Set speed to 4800bps. |
|------------------------+-----------------------------------|
| í H6 | Set speed to 9600bps. |
|------------------------+-----------------------------------|
| H7 | Set speed to 19.2Kbps. |
|------------------------+-----------------------------------|
| H8 | Set speed to 38.4Kbps. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CHANGE PROFILE CHANNEL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | PROn |
|--------------+---------------------------------------------|
| Description: | Selects which channel’s profile is being |
| | edited. |
|------------------------------------------------------------|
| Command | Function |
|---------------------+--------------------------------------|
| PRO1 | Edit profile for channel 1. |
|---------------------+--------------------------------------|
| PRO2 | Edit profile for channel 2. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS SIGNAL - NO CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | NCTS 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the CTS signal |
| | when there is no ISDN connection. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| NCTS 0x01 | CTS is forced low. |
|---------------+--------------------------------------------|
| NCTS 0x02 | CTS is forced high. |
|---------------+--------------------------------------------|
| NCTS 0x04 | CTS follows DTR. |
|---------------+--------------------------------------------|
| NCTS 0x08 | CTS follows RTS. |
|---------------+--------------------------------------------|
| NCTS 0x10 | CTS is forced high during connection and |
| | negotiation only. |
|---------------+--------------------------------------------|
| NCTS 0x20 | CTS follows remote DTR. |
|---------------+--------------------------------------------|
| NCTS 0x40 | CTS follows remote RTS. |
|---------------+--------------------------------------------|
| NCTS 0x80 | CTS follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS SIGNAL - NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | WCTS 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the CTS signal |
| | while dialing and negotiating a connection. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| WCTS 0x01 | CTS is forced low. |
|----------------+-------------------------------------------|
| WCTS 0x02 | CTS is forced high. |
|----------------+-------------------------------------------|
| WCTS 0x04 | CTS follows DTR. |
|----------------+-------------------------------------------|
| WCTS 0x08 | CTS follows RTS. |
|----------------+-------------------------------------------|
| WCTS 0x10 | CTS is forced high during connection and |
| | synchronization only. |
|----------------+-------------------------------------------|
| WCTS 0x20 | CTS follows remote DTR. |
|----------------+-------------------------------------------|
| WCTS 0x40 | CTS follows remote RTS. |
|----------------+-------------------------------------------|
| WCTS 0x80 | CTS follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CTS SIGNAL - CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | CCTS 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the CTS signal |
| | while connected. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| CCTS 0x01 | CTS is forced low. |
|---------------+--------------------------------------------|
| CCTS 0x02 | CTS is forced high. |
|---------------+--------------------------------------------|
| CCTS 0x04 | CTS follows DTR. |
|---------------+--------------------------------------------|
| CCTS 0x08 | CTS follows RTS. |
|---------------+--------------------------------------------|
| CCTS 0x10 | CTS is forced high during connection and |
| | synchronization only. |
|---------------+--------------------------------------------|
| CCTS 0x20 | CTS follows remote DTR. |
|---------------+--------------------------------------------|
| CCTS 0x40 | CTS follows remote RTS. |
|---------------+--------------------------------------------|
| CCTS 0x80 | CTS follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA LENGTH |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Ln |
|--------------+---------------------------------------------|
| Description: | Selects how many data bits will be |
| | transmitted. |
|------------------------------------------------------------|
| Command | Function |
|--------------------------+---------------------------------|
| í L0 | Synchronous mode. |
|--------------------------+---------------------------------|
| L7 | 7 data bits. |
|--------------------------+---------------------------------|
| L8 | 8 data bits. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA PARITY |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Mn |
|--------------+---------------------------------------------|
| Description: | Selects how many parity bits will be |
| | transmitted. |
|------------------------------------------------------------|
| Command | Function |
|----------------------------+-------------------------------|
| í M0 | No parity. |
|----------------------------+-------------------------------|
| M1 | Odd parity. |
|----------------------------+-------------------------------|
| M2 | Even parity. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DATA STOP |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Nn |
|--------------+---------------------------------------------|
| Description: | Selects how many stop bits will be |
| | transmitted. |
|------------------------------------------------------------|
| Command | Function |
|-----------------------------+------------------------------|
| í M1 | 1 stop bit. |
|-----------------------------+------------------------------|
| M2 | 2 stop bits. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCD SIGNAL - NO CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | NDCD 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behavior of the DCD signal |
| | when there is no ISDN connection. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| NDCD 0x01 | DCD is forced low. |
|---------------+--------------------------------------------|
| NDCD 0x02 | DCD is forced high. |
|---------------+--------------------------------------------|
| NDCD 0x04 | DCD follows DTR. |
|---------------+--------------------------------------------|
| NDCD 0x08 | DCD follows RTS. |
|---------------+--------------------------------------------|
| NDCD 0x10 | DCD is forced high during connection and |
| | negotiation only. |
|---------------+--------------------------------------------|
| NDCD 0x20 | DCD follows remote DTR. |
|---------------+--------------------------------------------|
| NDCD 0x40 | DCD follows remote RTS. |
|---------------+--------------------------------------------|
| NDCD 0x80 | DCD follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCD SIGNAL - NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | WDCD 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behavior of the DCD signal |
| | while dialing and negotiating a connection. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| WDCD 0x01 | DCD is forced low. |
|----------------+-------------------------------------------|
| WDCD 0x02 | DCD is forced high. |
|----------------+-------------------------------------------|
| WDCD 0x04 | DCD follows DTR. |
|----------------+-------------------------------------------|
| WDCD 0x08 | DCD follows RTS. |
|----------------+-------------------------------------------|
| WDCD 0x10 | DCD is forced high during connection and |
| | synchronization only. |
|----------------+-------------------------------------------|
| WDCD 0x20 | DCD follows remote DTR. |
|----------------+-------------------------------------------|
| WDCD 0x40 | DCD follows remote RTS. |
|----------------+-------------------------------------------|
| WDCD 0x80 | DCD follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DCD SIGNAL - CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | CDCD 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the DCD signal |
| | while connected. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| CDCD 0x01 | DCD is forced low. |
|---------------+--------------------------------------------|
| CDCD 0x02 | DCD is forced high. |
|---------------+--------------------------------------------|
| CDCD 0x04 | DCD follows DTR. |
|---------------+--------------------------------------------|
| CDCD 0x08 | DCD follows RTS. |
|---------------+--------------------------------------------|
| CDCD 0x10 | DCD is forced high during connection and |
| | synchronization only. |
|---------------+--------------------------------------------|
| CDCD 0x20 | DCD follows remote DTR. |
|---------------+--------------------------------------------|
| CDCD 0x40 | DCD follows remote RTS. |
|---------------+--------------------------------------------|
| CDCD 0x80 | DCD follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DEBUG PROFILE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | TEST |
|--------------+---------------------------------------------|
| Description: | Displays the profile editor debug page. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | En |
|--------------+---------------------------------------------|
| Description: | Selects the dial mode the TA will use. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| í E1 | Manual dialing only; prompt for number |
| | will be displayed. |
|---------------+--------------------------------------------|
| E2 | Asynchronous V.25bis dial mode. |
|---------------+--------------------------------------------|
| E3 | Hotline dial mode; DTR is used for call |
| | signalling. |
|---------------+--------------------------------------------|
| E4 | Hotline dial mode; RTS is used for call |
| | signalling. |
|---------------+--------------------------------------------|
| E5 | Hotline dial mode; automatic dial attempt. |
|---------------+--------------------------------------------|
| E6 | Incoming calls only. |
|---------------+--------------------------------------------|
| E7 | Hayes dialing mode. |
|---------------+--------------------------------------------|
| E8 | Synchronous V.25bis dial mode. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DSR SIGNAL - NO CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | NDSR 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the DSR signal |
| | when there is no ISDN connection. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| NDSR 0x01 | DSR is forced low. |
|---------------+--------------------------------------------|
| NDSR 0x02 | DSR is forced high. |
|---------------+--------------------------------------------|
| NDSR 0x04 | DSR follows DTR. |
|---------------+--------------------------------------------|
| NDSR 0x08 | DSR follows RTS. |
|---------------+--------------------------------------------|
| NDSR 0x10 | DSR is forced high during connection and |
| | negotiation only. |
|---------------+--------------------------------------------|
| NDSR 0x20 | DSR follows remote DTR. |
|---------------+--------------------------------------------|
| NDSR 0x40 | DSR follows remote RTS. |
|---------------+--------------------------------------------|
| NDSR 0x80 | DSR follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DSR SIGNAL - NEGOTIATION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | WDSR 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the DSR signal |
| | while dialing and negotiating a connection. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| WDSR 0x01 | DSR is forced low. |
|----------------+-------------------------------------------|
| WDSR 0x02 | DSR is forced high. |
|----------------+-------------------------------------------|
| WDSR 0x04 | DSR follows DTR. |
|----------------+-------------------------------------------|
| WDSR 0x08 | DSR follows RTS. |
|----------------+-------------------------------------------|
| WDSR 0x10 | DSR is forced high during connection and |
| | synchronization only. |
|----------------+-------------------------------------------|
| WDSR 0x20 | DSR follows remote DTR. |
|----------------+-------------------------------------------|
| WDSR 0x40 | DSR follows remote RTS. |
|----------------+-------------------------------------------|
| WDSR 0x80 | DSR follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DSR SIGNAL - CONNECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | CDSR 0xhh |
|--------------+---------------------------------------------|
| Description: | Controls the behaviour of the DSR signal |
| | while connected. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| CDSR 0x01 | DSR is forced low. |
|---------------+--------------------------------------------|
| CDSR 0x02 | DSR is forced high. |
|---------------+--------------------------------------------|
| CDSR 0x04 | DSR follows DTR. |
|---------------+--------------------------------------------|
| CDSR 0x08 | DSR follows RTS. |
|---------------+--------------------------------------------|
| CDSR 0x10 | DSR is forced high during connection and |
| | synchronization only. |
|---------------+--------------------------------------------|
| CDSR 0x20 | DSR follows remote DTR. |
|---------------+--------------------------------------------|
| CDSR 0x40 | DSR follows remote RTS. |
|---------------+--------------------------------------------|
| CDSR 0x80 | DSR follows V.110 flow control. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DTE/DCE MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Sn |
|--------------+---------------------------------------------|
| Description: | Sets whether the TA will operate as a DTE |
| | or a DCE device. |
|------------------------------------------------------------|
| Command | Function |
|-----------------------+------------------------------------|
| í S0 | TA will operate as DCE. |
|-----------------------+------------------------------------|
| S1 | TA will operate as DTE. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DTR SIGNAL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Dn |
|--------------+---------------------------------------------|
| Description: | Controls the operation of the Data Terminal |
| | Ready signal. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| D0 | Incoming calls accepted regardless of DTR |
| | state; low DTR does not disconnect. |
|----------------+-------------------------------------------|
| í D1 | Incoming calls accepted only if DTR is |
| | high; DTR or RTS transition to high will |
| | initiate a hotline call if in hotline |
| | mode; low DTR disconnects. |
|----------------+-------------------------------------------|
| D2 | Incoming calls accepted only if DTR is |
| | high; high DTR or RTS will initiate a |
| | hotline call if in hotline mode; low DTR |
| | disconnects. |
|----------------+-------------------------------------------|
| D3 | Incoming calls accepted regardless of DTR |
| | state; DTR or RTS transition to high will |
| | initiate a hotline call if in hotline |
| | mode; low DTR disconnects. |
|----------------+-------------------------------------------|
| D4 | Incoming calls accepted regardless of DTR |
| | state; high DTR or RTS will initiate a |
| | hotline call if in hotline mode; low DTR |
| | disconnects. |
|----------------+-------------------------------------------|
| D5 | Incoming calls accepted only if DTR is |
| | high; DTR or RTS transition to high will |
| | initiate a hotline call if in hotline |
| | mode; low DTR does not disconnect. |
|----------------+-------------------------------------------|
| D6 | Incoming calls accepted only if DTR is |
| | high; high DTR or RTS will initiate a |
| | hotline call if in hotline mode; low DTR |
| | does not disconnect. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EAZ |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | An |
|--------------+---------------------------------------------|
| Description: | Sets which incoming calls are answered. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| A0 | All incoming calls are answered; all |
| | channels are notified of the call. |
|---------------+--------------------------------------------|
| A1 - A8 | Only calls with a matching EAZ are |
| | answered. |
|---------------+--------------------------------------------|
| A9 | All incoming calls are answered; only the |
| | channel matching the EAZ is notified of |
| | the call. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EAZ - EDITOR |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Tn |
|--------------+---------------------------------------------|
| Description: | Sets which incoming calls should be routed |
| | for remote configuration. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| T0 | Only calls ending in "e" are routed to |
| | the editor. |
|----------------+-------------------------------------------|
| T1 - T8 | Only calls with a matching EAZ are |
| | answered. |
|----------------+-------------------------------------------|
| T9 | Calls matching the EAZ or ending in "e" |
| | are routed to the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| ENTER PROFILE EDITOR |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Description: | Enters the profile editor so that changes |
| | may be made. |
|------------------------------------------------------------|
| Mode | Command |
|---------------+--------------------------------------------|
| Manual dial | <CR><ESC> |
|---------------+--------------------------------------------|
| V.25bis dial | <CR><ESC> |
|---------------+--------------------------------------------|
| Hayes dial | AT<CR><ESC> |
|---------------+--------------------------------------------|
| All other | Push reset button, then <CR><CR><ESC><ESC> |
| modes | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| EXIT PROFILE EDITOR |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | EXIT |
| | |
| | <ESC> |
|--------------+---------------------------------------------|
| Description: | Quits the editor without saving changes. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL MODE - DCE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Bn |
|--------------+---------------------------------------------|
| Description: | Sets the type of flow control used. |
|------------------------------------------------------------|
| Command | Function |
|------------------+-----------------------------------------|
| B0 | Flow control disabled. |
|------------------+-----------------------------------------|
| í B1 | XON/XOFF flow control enabled. |
|------------------+-----------------------------------------|
| B2 | CTS flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL MODE - DTE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Cn |
|--------------+---------------------------------------------|
| Description: | Sets the type of flow control used. |
|------------------------------------------------------------|
| Command | Function |
|------------------+-----------------------------------------|
| C0 | Flow control disabled. |
|------------------+-----------------------------------------|
| í C1 | XON/XOFF flow control enabled. |
|------------------+-----------------------------------------|
| C2 | RTS flow control enabled. |
|------------------+-----------------------------------------|
| C3 | DTR flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| HOTLINE NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | HOT <#> |
|--------------+---------------------------------------------|
| Description: | Sets the number for hotline calling. If no |
| | number is given, hotline calling will not |
| | be allowed. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INACTIVITY TIMER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Fn |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0 - 60 |
|--------------+---------------------------------------------|
| Unit: | 1 minute |
|--------------+---------------------------------------------|
| Description: | Sets the amount of time that there must be |
| | no activity on the ISDN line before the TA |
| | disconnects. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| INCOMING CALL NUMBER |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | RUFn <#> |
|--------------+---------------------------------------------|
| Description: | Sets the number in position n of allowed |
| | incoming calls. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LANGUAGE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Kn |
|--------------+---------------------------------------------|
| Description: | Selects the language the TA will display |
| | messages in. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| K0 | Messages will be displayed in English. |
|---------------+--------------------------------------------|
| í K1 | Messages will be displayed in German. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LINE TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Rn |
|--------------+---------------------------------------------|
| Description: | Sets the type of line the TA will be |
| | operating on. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| í R0 | ISDN with BRI service. |
|---------------+--------------------------------------------|
| R1 | Group 3 leased line service with 1TR6. |
|---------------+--------------------------------------------|
| R2 | Group 2 leased line, 2B+D or B+D. |
|---------------+--------------------------------------------|
| R3 | Group 0 leased line, single B channel |
| | only. |
|---------------+--------------------------------------------|
| R4 | Point-to-point switched line. |
|---------------+--------------------------------------------|
| R5 | Point-to-point group 3 leased line with |
| | 1TR6. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LLC - INCOMING |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Pn |
|--------------+---------------------------------------------|
| Description: | Sets the use of LLC for incoming DSS1 |
| | calls. |
|------------------------------------------------------------|
| Command | Function |
|---------------+--------------------------------------------|
| P1 | Only calls with matching LLC will be |
| | answered. |
|---------------+--------------------------------------------|
| í P2 | Ignore LLC when answering calls. |
|---------------+--------------------------------------------|
| P3 | All data calls will be answered. |
|---------------+--------------------------------------------|
| P4 | All calls will be answered. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LLC - OUTGOING |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | On |
|--------------+---------------------------------------------|
| Description: | Sets the use of LLC for outgoing DSS1 |
| | calls. |
|------------------------------------------------------------|
| Command | Function |
|-----------------------+------------------------------------|
| O1 | Standard LLC enabled. |
|-----------------------+------------------------------------|
| í O2 | LLC disabled. |
|-----------------------+------------------------------------|
| O3 | User-defined LLC enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LLC - USER-DEFINED DATA OCTET |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | LLC=hh hh hh.. |
|--------------+---------------------------------------------|
| Description: | Sets the user-defined LLC octets in |
| | hexadecimal. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCAL SERIAL PORT SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Gn |
|--------------+---------------------------------------------|
| Description: | Sets the speed of the serial port. |
|------------------------------------------------------------|
| Command | Function |
|---------------------+--------------------------------------|
| G1 | Set speed to 300bps. |
|---------------------+--------------------------------------|
| G2 | Set speed to 600bps. |
|---------------------+--------------------------------------|
| G3 | Set speed to 1200bps. |
|---------------------+--------------------------------------|
| G4 | Set speed to 2400bps. |
|---------------------+--------------------------------------|
| G5 | Set speed to 4800bps. |
|---------------------+--------------------------------------|
| í G6 | Set speed to 9600bps. |
|---------------------+--------------------------------------|
| G7 | Set speed to 19.2Kbps. |
|---------------------+--------------------------------------|
| G8 | Set speed to 38.4Kbps. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| LOCK SERIAL PORT SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | In |
|--------------+---------------------------------------------|
| Description: | Selects whether the serial port speed will |
| | be adjusted to the DTE speed. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| I0 | Serial port speed locked. |
|----------------+-------------------------------------------|
| í I1 | Serial port speed will match DTE speed. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MALL <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for both |
| | channels of the TA and the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - TA |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MTAX <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for both |
| | channels of the TA. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - EDITOR |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MEDX <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for both |
| | channels of the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - EDITOR CHANNEL 1 |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MED1 <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for channel 1 |
| | of the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - EDITOR CHANNEL 2 |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MED2 <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for channel 2 |
| | of the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - TA CHANNEL 1 |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MTA1 <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for channel 1 |
| | of the TA. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MSN - TA CHANNEL 2 |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | MTA2 <#>*n |
|--------------+---------------------------------------------|
| Description: | Sets the MSN and subaddress for channel 2 |
| | of the TA. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| NEXT PAGE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | NEXT |
|--------------+---------------------------------------------|
| Description: | Shows the next page of values. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PREVIOUS PAGE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | PREV |
|--------------+---------------------------------------------|
| Description: | Shows the previous page of values. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | PWD xxxx |
|--------------+---------------------------------------------|
| Description: | Sets the password for remote configuration. |
| | If no password is given, no password will |
| | be required. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| RESET TO FACTORY DEFAULTS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | DEFA |
|--------------+---------------------------------------------|
| Description: | Resets all settings to their factory |
| | defaults. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SAVE PROFILE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | SAVE |
|--------------+---------------------------------------------|
| Description: | Saves the current settings into the profile |
| | and quits the editor. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERVICE INDICATOR |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Pn |
|--------------+---------------------------------------------|
| Description: | Sets the 1TR6 Service Indicator. |
|------------------------------------------------------------|
| Command | Function |
|----------------+-------------------------------------------|
| í P0 | Service Indicator reports standard line. |
|----------------+-------------------------------------------|
| P1 | Service Indicator reports Private SI. |
|----------------+-------------------------------------------|
| P2 | Service Indicator reports Private 2. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERVICE INDICATOR DETAILS |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | On |
|--------------+---------------------------------------------|
| Description: | Sets the details for the 1TR6 Service |
| | Indicator. |
|------------------------------------------------------------|
| Pn Setting | Command | Function |
|---------------+---------+----------------------------------|
| P0 | í O1 | Service Indicator reports 1TR6. |
|---------------+---------+----------------------------------|
| | O2 | Service Indicator reports X.21. |
|---------------+---------+----------------------------------|
| | O3 | Service Indicator reports AOI |
| | | synch/asynch mode. |
|---------------+---------+----------------------------------|
| P1 | í O1 | Service Indicator reports V.24 |
| | | asynch. |
|---------------+---------+----------------------------------|
| | O2 | Service Indicator reports 64Kbps |
| | | asynch. |
|---------------+---------+----------------------------------|
| | O3 | Service Indicator reports V.24 |
| | | BTX. |
|---------------+---------+----------------------------------|
| | O4 | Service Indicator reports V.24 |
| | | Text. |
|---------------+---------+----------------------------------|
| | O5 | Service Indicator reports 64Kbps |
| | | PC-Net. |
|---------------+---------+----------------------------------|
| P2 | í O1 | Service Indicator reports |
| | | Private 2 LLC with the data |
| | | octet equal to 0. |
|---------------+---------+----------------------------------|
| | O2 | Service Indicator reports |
| | | Private 2 LLC with the data |
| | | octet not equal to 0. |
|---------------+---------+----------------------------------|
| | O3 | Service Indicator reports |
| | | Private 2 with the data octet |
| | | equal to 0. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SYNCHRONOUS SPEED |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | Qn |
|--------------+---------------------------------------------|
| Description: | Selects what data rate the TA will operate |
| | in when in synchronous mode. |
|------------------------------------------------------------|
| Command | Function |
|-------------------+----------------------------------------|
| Q0 | Use V.24 asynchronous mode. |
|-------------------+----------------------------------------|
| Q1 | Use data rate set with Gn and Hn. |
|-------------------+----------------------------------------|
| í Q2 | Use 64Kbps data rate. |
|-------------------+----------------------------------------|
| Q3 | Use 56Kbps data rate. |
|-------------------+----------------------------------------|
| Q4 | Use 48Kbps data rate. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| UPDATE PROFILE |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | UPDA |
|--------------+---------------------------------------------|
| Description: | Saves the current settings into the |
| | profile. |
+------------------------------------------------------------+