TEXT View Source
# WILDCARD TECHNOLOGIES, INC.
SATISFAXTION MOBILE PDMCIA9023COMBO
Card Type Modem (asynchronous), Ethernet
Chipset Intel 82595TX
Maximum Onboard Memory 160KB DRAM/128KB PROM
Network Transfer Rate 10Mbps
Maximum Data Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus PCMCIA Type II
Fax Class Class I & II
Data Modulation Bell 103A/212A
ITU-T V.21, V.22, V.23, V.22bis, V.32,
V.32bis, V.34
Rockwell V.FC
Fax Modulation Unidentified
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
Topology Star
Wire Type Unshielded twisted pair
Boot ROM Not available
52771
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, A/ |
|------------------------------------------------------------|
| A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \G, \J, \K, \L, \N |
|------------------------------------------------------------|
| %C, %L, %Q |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| -K, -Q, *H, )M, @M, :E, +MS |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, |
| S14, S16, S18, S21, S22, S23, S24, S25, |
|------------------------------------------------------------|
| S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, |
| S39, S40, S41, S46, S48, S82, S86, S91, |
|------------------------------------------------------------|
| S92, S95, S201 |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] %En [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls auto-retrain mode and |
| | fallback/fall-forward |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| í %E0 | Auto-retrain disabled. |
|--------------+---------------------------------------------|
| %E1 | Auto-retrain enabled. |
|--------------+---------------------------------------------|
| %E2 | Auto-fallback/fall-forward enabled. |
|--------------+---------------------------------------------|
| %E3 | Auto-retrain and fast disconnect enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC |
|------------------------------------------------------------|
| Format | AT [cmds] S19=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0 - 63 |
|--------------+---------------------------------------------|
| Unit: | Bit-mapped |
|--------------+---------------------------------------------|
| Description: | Sets options for Hayes AutoSync functions. |
|--------------+---------------------------------------------|
| Bit | Value | Function |
|------+-------+---------------------------------------------|
| 0 | 0 | Not used. |
|------+-------+---------------------------------------------|
| 1 | í 0 | BSC enabled. |
| | | |
| | 1 | HDLC enabled. |
|------+-------+---------------------------------------------|
| 2 | í 0 | HDLC address detection disabled. |
| | | |
| | 1 | HDLC address detection enabled. |
|------+-------+---------------------------------------------|
| 3 | í 0 | NRZI bit encoding enabled. |
| | | |
| | 1 | NRZ bit encoding enabled. |
|------+-------+---------------------------------------------|
| 4 | í 0 | Mark idle enabled. |
| | | |
| | 1 | Flag or sync idle enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| AUTOSYNC HDLC ADDRESS |
|------------------------------------------------------------|
| Type: | Register |
|--------------+---------------------------------------------|
| Format: | AT [cmds] S20=n [cmds] |
|--------------+---------------------------------------------|
| Default: | 0 |
|--------------+---------------------------------------------|
| Range: | 0-255 |
|--------------+---------------------------------------------|
| Unit: | Unidentified |
|--------------+---------------------------------------------|
| Description: | Sets the HDLC address or BSC character. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| COUNTRY CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *NCnn [cmds] |
|--------------+---------------------------------------------|
| Description: | Changes the country code of the modem to |
| | nn. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DJ | MNP10 link will be negotiated at 1200bps |
| | for this call. |
|--------------+---------------------------------------------|
| DK | MNP10 power level adjustment enabled for |
| | this call. |
|--------------+---------------------------------------------|
| DL | Re-dial last number. |
|--------------+---------------------------------------------|
| DP | Pulse dialing enabled. |
|--------------+---------------------------------------------|
| DR | Answer mode enabled; originate mode |
| | disabled following handshake initiation. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n. |
|--------------+---------------------------------------------|
| DT | Tone dialing enabled. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register. |
|--------------+---------------------------------------------|
| D"WXY" | Optional method of denoting telephone |
| | numbers. Letters enclosed in quotes are |
| | interpreted as numbers according to the |
| | system found on a telephone keypad. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D$ | Wait for prompt tone detection function |
| | enabled. Modem waits for prompt tone for |
| | amount of time specified by the S7 command. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
|--------------+---------------------------------------------|
| D^ | Calling tone toggled from current setting |
| | for this call. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PULSE DIAL CODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Zn [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets the currently active pulse dialing |
| | code. |
|------------------------------------------------------------|
| Command | Function |
|----------------------------+-------------------------------|
| í *Z0 | Use dial code 0. |
|----------------------------+-------------------------------|
| *Z1 | Use dial code 1. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \F [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all stored phone numbers. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| FLOW CONTROL |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] &Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Enables flow control options. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| &K0 | Flow control disabled. |
|--------------+---------------------------------------------|
| í &K3 | RTS/CTS flow control enabled. |
|--------------+---------------------------------------------|
| &K4 | XON/XOFF flow control enabled. |
|--------------+---------------------------------------------|
| &K5 | Transparent XON/XOFF flow control enabled. |
|--------------+---------------------------------------------|
| &K6 | RTS/CTS and XON/XOFF flow control enabled. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports modem model and speed |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum |
|--------------+---------------------------------------------|
| I3 | Reports firmware revision. |
|--------------+---------------------------------------------|
| I5 | Reports country code. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REQUEST LIST OF FORBIDDEN NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *B [cmds] |
|--------------+---------------------------------------------|
| Description: | Requests the list of forbidden numbers from |
| | the modem. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REQUEST LIST OF DELAYED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *D [cmds] |
|--------------+---------------------------------------------|
| Description: | Requests the list of delayed numbers from |
| | the modem. |