The linux NCR53C8XX driver README file

Written by Gerard Roudier <groudier@club-internet.fr>
21 Rue Carnot
95170 DEUIL LA BARRE - FRANCE

12 June 1995
===============================================================================

1.  Introduction
2.  Supported chips and SCSI features
3.  Summary of other supported features
4.  Memory mapped IO versus normal IO
5.  Tagged command queueing
6.  Parity checking
7.  Profiling information
8.  Control commands
      8.1  Set minimum synchronous period
      8.2  Set wide size
      8.3  Set maximum number of concurrent tagged commands
      8.4  Set order type for tagged command
      8.5  Set debug mode
      8.6  Clear profile counters
9.  Configuration parameters
10. Some constants and flags of the ncr53c8xx.h header files
11. Provided files
12. Installation procedure for Linux version 1
13. Installation procedure for Linux version 2
14. Control commands under linux-1.2.13
15. Known problems
      15.1 Tagged commands with Iomega Jaz device
      15.2 Tagged command queueing cannot be disabled at run time

===============================================================================

1. Introduction

This driver has been ported from FreeBSD to Linux and is currently 
maintained by:
          Gerard Roudier              <groudier@club-internet.fr>

The original driver has been written for 386bsd and FreeBSD by
          Wolfgang Stanglmeier        <wolf@cologne.de>
          Stefan Esser                <se@mi.Uni-Koeln.de>

You can find technical informations about the NCR 8xx family in the PCI-HOWTO 
written by Michael Will and in the SCSI-HOWTO written by Drew Eckhardt.

Informations about new chips is available at SYMBIOS web server:
          http://www.symbios.com

This short documentation only describes the features of the NCR53C8XX driver, 
configuration parameters and control commands available through the proc scsi 
file system read / write operations.

This driver has been tested ok with linux/i386  and is currently untested
under linux/Alpha. If you intend to use this driver under linux/Alpha, just 
try it first with read-only or mounted read-only devices.

I am not a native speaker of English and there is probably lots of 
mistakes in this README file. Any help will be welcome.


2. Supported chips and SCSI features

The following features are supported for all chips:

	Synchronous negotiation
	Disconnection
	Tagged command queuing
	Scsi parity checking
	Master parity checking

"Wide negotiation" is supported for chips that allow it.
The following table shows some characteristics of NCR 8xx family chips:

       On board                        Supported by    Tested with
Chip   SDMS BIOS   Wide   Ultra Scsi   the driver      the driver
----   ---------   ----   ----------   ------------    -----------
810        N         N        N            Y             Y
810A       N         N        N            Y             Y
815        Y         N        N            Y             Y
825        Y         Y        N            Y             Y
825A       Y         Y        N            Y             Not yet
875        Y         Y        Y(1)         Y             Not yet

(1) Ultra scsi extensions will be supported in a future release of the 
    driver.


3. Summary of other supported features.

        Module:                allow to load the driver
        Memory mapped IO:      increase performances
        Profiling information: read operations from the proc scsi file system
        Control commands:      write operations to the proc scsi file system
        Debugging information: written to syslog (expert only)
	Scatter / gather
	Shared interrupt


4. Memory mapped IO versus normal IO

Memory mapped IO have less latency than normal IO.
Since linux-1.3.x, memory mapped IO is used rather than normal IO.
Memory mapped IO seems to works fine on most hardware configuration, but some 
bad designed motherboards may break this feature.

During initialisation phase, the driver first tries to use memory mapped io.
If nothing seems wrong, it will use memory mapped io.
If a flaw is detected,  it will use normal io.

However, it's possible that memory mapped io does not work properly and the 
driver has not detected the problem.

The configuration option CONFIG_SCSI_NCR53C8XX_IOMAPPED allow to force the 
driver to use normal io in all cases.


5. Tagged command queueing

Some scsi devices donnot support properly tagged command queuing.
A safe configuration can be to not enable tagged command queuing support at 
boot-up, and to enable support of it with the control command "settags" 
described further in this text.

Once you are sure that all your devices support properly tagged command queuing,
you can enable it by default with the CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE 
configuration option.


6. Parity checking

The driver supports scsi parity checking and PCI bus master parity checking.
These features must be enabled in order to ensure safe data transfers.
However, some flawed devices or mother boards will have problems with 
parity. You can disable parity by choosing first "CONFIG_EXPERIMENTAL".
Then, "make config" will allow to set the following configuration options:

   CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK  (disable scsi parity checking)
   CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK (disable master parity checking)


7. Profiling information

Profiling information are available through the proc scsi file system.
The device associated with a host has the following pathname:
          /proc/scsi/ncr53c8xx/N     (N=0,1,2 ....)

Generally, only 1 board is used on hardware configuration, and the device is:
          /proc/scsi/ncr53c8xx/0

However, if the driver has been made as module, the number of the host is 
incremented each time the driver is loaded.

In order to display profiling informations, just enter:
         cat /proc/scsi/ncr53c8xx/0
and you will get something like the following text:

-------------------------------------------------------
General informations:
  Chip NCR53C810, device id 0x1, revision id 0x2
  IO port address 0x6000, IRQ number 10
  Using memory mapped IO at virtual address 0x282c000
Profiling informations:
  num_trans    = 18014
  num_kbytes   = 671314
  num_disc     = 25763
  num_break    = 1673
  num_int      = 1685
  num_fly      = 18038
  ms_setup     = 4940
  ms_data      = 369940
  ms_disc      = 183090
  ms_post      = 1320
-------------------------------------------------------

General informations are easy to understand. The device id and the 
revision id identify the scsi chip as follow:

Chip    Device id     Revision Id
----    ---------     -----------
810       0x1            <  0x10
810A      0x1            >= 0x10
815       0x4
825       0x3            <  0x10
860       0x6
825A      0x3            >= 0x10
875       0xf

The profiling informations are updated upon completion of scsi commands.
The data structure is allocated and zeroed when the host adapter is 
attached. So, if the driver is a module, the profile counters are cleared each 
time the driver is loaded.
The "clearprof" command allow to clear these counters at any time.

The following counters are available:
("num" prefix means "number of", "ms" means milli-seconds)

num_trans
	Number of completed commands
	Example above: 18014 completed commands

num_kbytes
	Number of kbytes transferred
	Example above: 671 MB transferred

num_disc
	Number of scsi disconnections
	Example above: 25763 scsi disconnections

num_break
	number of script interruptions (phase mismatch)
	Example above: 1673 script interruptions

num_int
	Number of interrupts other than "on the fly"
	Example above: 1685 interruptions not "on the fly"

num_fly
	Number of interrupts "on the fly"
	Example above: 18038 interruptions "on the fly"

ms_setup
	Elapsed time for scsi commands setups
	Example above: 4.94 seconds

ms_data
	Elapsed time for data transfers
	Example above: 369.94 seconds spent for data transfer

ms_disc
	Elapsed time for scsi disconnections
	Example above: 183.09 seconds spent disconnected

ms_post
	Elapsed time for command post processing
	(time from scsi status get to command completion call)
	Example above: 1.32 seconds spent for post processing

Due to the 1/100 second tick of the system clock, "ms_post" time may be 
wrong.

In the example above, we got 18038 interrupts "on the fly" and only 1673 script 
breaks probably due to disconnections inside a segment of the scatter list. 
It is an excellent result due to the fact that the driver tries to use small 
data segments (512) for the scatter list. The CPU load of this rescatter process 
is acceptable. Unlike other scsi processors, NCR53C8XX controllers do not need  
large data chunks in order to get better performances, and it seems that it 
is the opposite.
The scatter/gather algorithm of the middle scsi driver is not optimal for 
NCR scsi processors and should be tunable according to host type.

You can tune the "wished" segment size for the scatterlist by changing the 
following "define" in the file ncr53c8xx.h.
Use only power of 2 greater than 512 (1024, 2048 or 4096).

SCSI_NCR_SEGMENT_SIZE		(default: 512)


8. Control commands

Control commands can be sent to the driver with write operations to the 
proc scsi file system. The generic command syntax is the following:

      echo "<verb> <parameters>" >/proc/scsi/ncr53c8xx/0
      (assumes controller number is 0)

Available commands:

8.1 Set minimum synchronous period

    setsync <target> <period>

    target:    target number
    period:    minimum synchronous period in nano-seconds.
               Maximum speed = 1000/(4*period) MB/second

    Specify a period of 255, to force asynchronous transfer mode.

8.2 Set wide size

    setwide <target> <size>

    target:    target number
    size:      0=8 bits, 1=16bits

8.3 Set maximum number of concurrent tagged commands
 
    settags <target> <tags>

    target:    target number
    tags:      number of concurrent tagged commands
               must not be greater than SCSI_NCR_MAX_TAGS (default: 4)
               must not be lower that 1 (see: known problems)

8.4 Set order type for tagged command

    setorder <order>

    order:     3 possible values:
               simple: use SIMPLE TAG for all operations (read and write)
               ordered: use ORDERED TAG for all operations
               default: use default tag type,
                        SIMPLE  TAG for read  operations
                        ORDERED TAG for write operations


8.5 Set debug mode

    setdebug <list of debug flags>

    Available debug flags:
        alloc:   print infos about memory allocations (ccb, lcb)
        queue:   print infos about insertions into the command start queue
        result:  print sense data on CHECK CONDITION status
        scatter: print infos about the scatter process
        scripts: print infos about the script binding process
	tiny:    print minimal debugging informations
	timing:  print timing informations of the ncr chip.
	nego:    print informations about scsi negotiations
	phase:   print informations on script interruptions


8.6 Clear profile counters

    clearprof

    The profile counters are automatically cleared when the amount of data 
    transfered reach 1000 GB in order to avoid overflow.
    The "clearprof" command allow to clear these counters at any time.


9. Configuration parameters

If the firmware of all your devices is perfect enough, all the features 
supported by the driver can be enabled at start-up.
However, if only one has a flaw for some scsi feature, you can disable the 
support by the driver of this feature at linux start-up and enable this 
feature after boot-up only for devices that support it safely.

CONFIG_SCSI_NCR53C8XX_IOMAPPED       (default answer: n)
    Answer "y" if you suspect your mother board to not allow memory mapped IO.
    May slow down a little performances.

CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE    (default answer: n)
    Answer "y" if you are sure that all your scsi devices that are able to 
    accept tagged commands will proceed safely.

CONFIG_SCSI_NCR53C8XX_FORCE_ASYNCHRONOUS (default answer: n)
    This option allow to force asynchronous transfer mode for all scsi devices. 
 
CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO (default answer: n)
    Force synchronous negotiation for all scsi-2 devices.
    Some scsi-2 devices do not report this feature in byte 7 of inquiry 
    response and however support it properly (TAMARACK scanners for example).

CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT   (default and only reasonnable answer: n)
    If you suspect a device of yours to not support properly disconnections,
    you can answer "y". Then, all scsi devices will never disconnect the bus 
    even while long scsi operations.


10. Some constants and flags of the ncr53c8xx.h header files

Some of these are defined from the configuration parameters.
To change other "defines", you must edit the header file.
Do that only if you know what you are doing.

SCSI_NCR_IOMAPPED		(default: not defined)
	If defined, normal IO is forced.

SCSI_NCR_SHARE_IRQ		(default: defined)
	If defined, request shared irq.
	
SCSI_NCR_MAX_TAGS		(default: 4)
	Maximum number of simultaneous tagged commands to a device.
	Can be changed by "settags <target> <maxtags>"

SCSI_NCR_ALWAYS_SIMPLE_TAG	(default: defined)
	Use SIMPLE TAG for read and write commands
	Can be changed by "setorder <ordered|simple|default>"

SCSI_NCR_TAGGED_QUEUE_DISABLED	(default: defined)
	If defined, tagged command queuing is disable at start-up.
	Can be changed by "settags <target> <maxtags>"

SCSI_NCR_NO_DISCONNECT		(default: not defined)
	If defined, targets are not allowed to disconnect.

SCSI_NCR_FORCE_SYNC_NEGO	(default: not defined)
	If defined, synchronous negotiation is tried for all scsi-2 devices.
	Can be changed by "setsync <target> <period>"

SCSI_NCR_DISABLE_MPARITY_CHECK	(default: not defined)
	If defined, master parity checking is disabled.

SCSI_NCR_DISABLE_PARITY_CHECK	(default: not defined)
	If defined, scsi parity checking is disabled.

SCSI_NCR_PROFILE		(default: defined)
	If defined, profile informations are gathered

SCSI_NCR_MAX_SCATTER		(default: 128)
	Scatter list size of the driver ccb.

SCSI_NCR_SEGMENT_SIZE		(default: 512)
	If defined, the driver try to use scatter segments of this size.
	If not defined, the Linux scatter list is used as is.

SCSI_NCR_MAX_TARGET		(default: 16)
	Max number of target per host.

SCSI_NCR_MAX_HOST		(default: 2)
	Max number of host controllers.

SCSI_NCR_SETTLE_TIME		(default: 2)
	Number of seconds the driver wait after reset.

SCSI_NCR_TIMEOUT_ALERT		(default: 3)
	If a pending command will time out after this amount of seconds,
	an ordered tag is used for the next command.
	Avoid timeouts for unordered tagged commands.

SCSI_NCR_CAN_QUEUE		(default: 7*SCSI_NCR_MAX_TAGS)
	Max number of commands that can be queued to a host.

SCSI_NCR_CMD_PER_LUN		(default: SCSI_NCR_MAX_TAGS)
	Max number of commands queued to a host for a device.

SCSI_NCR_SG_TABLESIZE		(default: SCSI_NCR_MAX_SCATTER-1)
	Max size of the Linux scatter/gather list.

SCSI_NCR_MAX_LUN	(default: 8)
	Max number of luns per target


11. Provided files

Driver and common files:

	README.ncr53c8xx	: this file
	ChangeLog.ncr53c8xx	: change log
	ncr53c8xx.h		: definitions
	ncr53c8xx.c		: the driver code
	scsitag.c		: command tool to enable tagged queue
	conf.modules		: sample of /etc/conf.modules

Installation procedure 1 replacing the standard NCR53c7,8xx driver:

	Install.ncr53c8xx	: installation script
	Uninstall.ncr53c8xx	: uninstallation script
	53c7,8xx.h		: included by hosts.c, override the standard driver

	Patch-1.2.13.ncr53c8xx     : patch for linux-1.2.13
	Patch-1.3.45-49.ncr53c8xx  : patch for linux-1.3.45 to linux-1.3.49
	Patch-1.3.50-100.ncr53c8xx : patch for linux-1.3.50 to linux-1.3.100

Installation procedure 2 adding the driver to the kernel tree:

	Install2.ncr53c8xx	   : installation script

	Patch2-2.0.0-1.ncr53c8xx   : patch for linux-2.0.0 and linux-2.0.1
	Patch2-Current.ncr53c8xx   : patch used for sub-levels > 1

Prior to installing the driver, you must untar the distribution, as follow:

	mkdir ncrB2L
	cd ncrB2L
	tar zxvf ncrBsd2Linux-1.12a-src.tar.gz


12. Installation procedure for Linux version 1

This install script only supports linux-1.2.13 and linux-1.3.45 to 1.3.100.

This procedure just move the standard driver files to SAVE_53 sub-directory 
of linux/drivers/scsi, copies the drivers file to that directory and patches 
the scsi Makefile.
The standard driver can be restored with Uninstall.ncr53c8xx

	If your linux directory is at the standard location
	"/usr/src/linux", just enter:
		Install.ncr53c8xx

	Else enter:
		Install.ncr53c8xx <your_linux_directory>

	Make the kernel:
		Change to linux source directory
		Configure with 53c7,8xx support (Y or m)  for Install.ncr53c8xx
		Make dependancies
		Make the kernel (use make zdisk first)
		Make and install modules if you have configured with 'm'

	Notes:
		Since release 1.3.90, additionnal configuation parameters 
		have been added for the standard NCR driver.
		Just reply Y or N as you want to these questions;
		The NCR53C8XX driver ignore those parameters.

	If you prefer the standard NCR driver of Linux:
	just enter:
		Uninstall.ncr53c8xx
	or
		Uninstall.ncr53c8xx <your_linux_directory>
	if your linux root is not /usr/src/linux.


13. Installation procedure for Linux version 2

This procedure add the driver to the kernel tree.
Using "make config" you can choose between the standard driver and the BSD one.
It is possible to configure the both drivers as module and to switch from one 
to the other at run time.
Take care to unload the current driver module before loading the other one.

	If your linux directory is at the standard location
	"/usr/src/linux", just enter:
		Install2.ncr53c8xx

	Else enter:
		Install2.ncr53c8xx <your_linux_directory>

	Make the kernel:
		Change to linux source directory
		Configure with NCR53C8XX support (Y or m)
		Make dependancies
		Make the kernel (use make zdisk first)
		Make and install modules if you have configured with 'm'


14. Control commands under linux-1.2.13

Profile data and control commands using the proc scsi file system are not 
available for linux-1.2.13.
The only control command available is "scsitag" which allows to enable 
tagged command queuing support after linux boot-up.

Tagged command queueing is disabled by default at system startup.

You can enable tagged queue per device with the following command:
	scsitag device_name (ex: scsitag /dev/sda)

Use "cc -o scsitag scsitag.c" to create the "scsitag" executable.


15. Known problems

15.1 Tagged commands with Iomega Jaz device

I never tried such devices, however it has been reported to me the following:
This device is capable of Tagged command queuing. However while spinning up,
it rejects Tagged commands. This behaviour is conforms to 6.8.2 of scsi-2 
specifications. The current behaviour of the driver in that situation is not 
satisfying. So do not enable Tagged command queuing for devices that are able 
to spin down.
The other problems that may appear are timeouts. The only way to avoid timeouts 
seems to edit linux/drivers/scsi/sd.c and to increase the current timeout 
values.

15.2 Tagged command queuing cannot be disabled at run time

Once Tagged command queuing has been enabled, the driver will not allow to 
disable this feature ("settags <target> 0" is not supported).
This problem is due to some limitations of the code added to the Linux version 
of the driver.

===============================================================================
End of NCR53C8XX driver README file
