Subj : RE: Config File
To   : GORD HANNAH
From : IB JOE
Date : Tue Feb 11 2003 04:17 pm

No, that was plain enough....

I have a few questions though...

I want to use this to call only a few boards... Maybe just a point address.
Is there a simple way to configure just a few system to call out on??

I have a copy of XLaxNode ... what is the command line to get that to compile
a nodelist??

Thanx

Joe





On Feb 11, 2003 08:19am, GORD HANNAH wrote to IB JOE:

 GH> Replying to a message from IB JOE 1:275/312 to ALL,

 GH> About Config File, On Mon Feb 10 2003

IJ>> Does anyone have a config file that is plain jane just to get bink
IJ>> up and running...

 GH> A little fancier than plain jane but will get you up and running, I
 GH> used this for years with a USR Sportster 28.8.

 GH> ;                            BINKLEY CONTROL FILE
 GH> ;
 GH> Serial      1234
 GH> System      Your BBS Name Here
 GH> Sysop       Your Name Here
 GH> Address   Your Node Number Here
 GH> MyLocation  Your Location as it appears in the Nodelist
 GH> MyPhone     +1-Finish your Phone Number
 GH> MyListFlags Your Nodelist Flags Here
 GH> ExtBaudRates
 GH> MyMaxBaud   57600
 GH> LockBaud
 GH> PickUpAll
 GH> Banner      Welcome to Your BBS
 GH> EnterBBS    Press Esc to enter the system or wait a few seconds. BBSNote
 GH> Thank you, now loading Maximus ...
 GH> DoingMail   Sorry; we are currently running a required 2:00-3:00 A.M.
 GH> mail-only event. Shell 1 c:\timed\timed.com
 GH> Shell 2 Bonk
 GH> Shell 3 MFM -ac:\BBS
 GH> Shell 4 UEDIT
 GH> Shell 5 IN.bat
 GH> Shell 6 Out.bat
 GH> Shell 7 Qedit c:\bbs\question.txt
 GH> Shell 8 LIST \bbs\INFO.log
 GH> Shell 9 DEL c:\mail\outbound\*.$$?
 GH> ; CHANGE THE FOLLOWING TO SUIT YOUR NEEDS

 GH> StatusLog    c:\BBS\Binkley.log
 GH> Downloads    e:\Private\
 GH> CaptureFile  c:\BBS\Binkterm.cap
 GH> NetMail      i:\Echo\
 GH> NetFile      c:\Mail\Inbound\
 GH> Hold         c:\Mail\Outbound\
 GH> Version7
 GH> LogLevel 5
 GH> Gong
 GH> ;
 GH> ;   Not all systems can handle the stresses of the Janusbaud
 GH> bi-directional ; protocol.  If you experience problems, comment out the
 GH> line below. ; JanusBaud      57600
 GH> ;
 GH> Unattended
 GH> Polltries      150
 GH> Nodelist       c:\Nodelist\
 GH> MaxReq         10
 GH> MaxBytes       2900000
 GH> About          c:\BBS\Error.txt
 GH> Okfile         c:\BBS\OKfile.lst
 GH> Avail          e:\New\ALLMARSH.zip
 GH> ReqOnUs
 GH> Timeout        20
 GH> BBS Batch
 GH> ScreenBlank    call
 GH> Colors  112  14  10  11   7  12 112   3
 GH> Boxtype 2
 GH> CursorCol 1
 GH> CursorRow 25
 GH> ;
 GH> ; Binkley 2.50 specific
 GH> Serial       12345
 GH> StartBlkLen  512
 GH> BlankWait    60
 GH> MaxTime      60
 GH> RingTries    3
 GH> ;
 GH> ; Binkley 2.55 specific
 GH> FileSec 3
 GH> MaxAreas c:\bbs\area.dat
 GH> ;
 GH> ; Binkley 2.59 specific
 GH> ;ModemRetry <modem response>
 GH> ;AltNumber <primary number> <alternate number>
 GH> ;==========================[ MODEM SETUP SECTION
 GH> ]============================ Port            2
 GH> Baud             57600
 GH> Carrier         80
 GH> Init
 GH> v~^~ATH0|`AT&F1|~ATM0&K1&S1S2=127S7=90S9=30S10=20S11=50|`ATS15=8S28=20|`
 GH> `AT+FCL ASS=0|` Prefix          ~AT+FCLASS=0DT
 GH> Suffix          `
 GH> Answer
 GH> ```AT+FCLASS=2\.0|`AT+FBO=1;+FAA=1;+FNR=1,1,1;+FLI="+1-250-786-7921";A|

 GH> ;In the above when receiving with Binkley: +FBO=1
 GH> ;In the above when receiving with BGFax:   +FBO=0
 GH> ;
 GH> PreDial         `
 GH> PreInit         |v``^``|
 GH> DTRHigh
 GH> ;
 GH> ; Add the following responses to Binkley.cfg in the same order!  Also ;
 GH> be sure to physically creade the sub-directory in FaxInDir ;
 GH> ModemIgnore   +FDM
 GH> ModemIgnore   RINGING
 GH> ModemIgnore   RING RESPONSE
 GH> ModemRinging  RING
 GH> ModemConnect  CONNECT
 GH> ModemIgnore   RRING
 GH> ModemFailure  BUSY
 GH> ModemFailure  VOICE
 GH> ModemFailure  ERROR
 GH> ModemFailure  OK
 GH> ModemFailure  NO CARRIER
 GH> ModemIncoming NO DIAL TONE
 GH> ModemIgnore   DIALING
 GH> ModemFailure  NO ANSWER
 GH> ModemIgnore   DIAL TONE
 GH> ModemFax      +FCO
 GH> FaxInDir      C:\BGFAX\IN
 GH> ;
 GH> ; AfterCall 34 ATI6I11|ATZ|       ; ) Just a bunch of samples of the ;
 GH> AfterCall 18 ATI6|              ; ) AfterCall function to record modem ;
 GH> AfterCall 14 ATI11|             ; ) stats in Binkley.log


 GH> I am also assuming that you are using some flavour of DOS.  Some
 GH> modifications will be needed for OS/2.

 GH> Hope this helps.  Keep us posted.

 GH> We are a fine board trying to make it better.
 GH> http://www.pris.bc.ca/ghannah
 GH> ghannah@pris.bc.ca
 GH> Cheers! Gord
 GH> -=Team OS/2=-
 GH> --- Timed/2 2.30+
 GH>  * Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)

.... Joe's Computer & BBS -=telnet.joesbbs.com=-
--- Platinum Xpress/Win/WINServer v3.0pr5
 * Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)

.